Study guide
9.2 NEC Article 300 Wiring Methods and Installation Workmanship
Texas Fire Alarm Installer License Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Texas Insurance Code Chapter 6002 Foundations
1.1 Chapter 6002 Purpose, Scope & Statutory Definitions 1.2 State Preemption and the Limits of Local Regulation 1.3 Commissioner and SFMO Authority; Adopted Standards and Editions 1.4 Activities Not Regulated: The § 6002.155 Exemptions 1.5 Required Device Labels, Listings and Consumer Information
2 Chapter 2: Certificates of Registration and Company Operating Rules
2.1 Registration Certificates: Main Office, Branch Office and Single Station 2.2 Insurance Requirements for Registered Firms 2.3 Business Location, Designated Employee and Vehicle Identification (§ 34.610) 2.4 Ownership Changes, Officer Changes and Revised Certificates
3 Chapter 3: Individual Licenses, Qualifying Tests and Renewal
3.1 The Six Texas Fire Alarm Licenses and What Each May Do 3.2 License Applications, Fingerprinting and Criminal History 3.3 The Qualifying Tests: TFM11, TFM12, TFM13, TFM14 and Their References 3.4 NICET, ESA and Professional Engineer Substitutions 3.5 Fees, the Two-Year Renewal Cycle and Late Renewal 3.6 Training Schools, Instructors and the Residential Technician Course
4 Chapter 4: Texas Field Practice — Installation, Service, Monitoring and Certification
4.1 Sales, Installation and Service Rules (§ 34.616) 4.2 Monitoring Requirements for Registered Firms (§ 34.616(c)) 4.3 The Installation Certificate (SF035) and Its Distribution 4.4 The Three-Stage Installation Inspection (§ 34.618) 4.5 Fire Alarm Plans and Record Drawings (§ 34.619)
5 Chapter 5: Texas Labels, Records and Enforcement
5.1 Installation and Service Labels (§§ 34.620–34.621) 5.2 Inspection/Test, Yellow and Red Labels and Impairment Notice 5.3 The Texas Recordkeeping and Retention Map 5.4 Prohibited Practices, Discipline, Enforcement and Penalties
6 Chapter 6: NFPA 72 Fundamentals, Power, Signals and Pathways
6.1 Identifying the Applicable NFPA Standards for TFM12 6.2 NFPA 72 Scope, Organization & Core Life Safety Definitions 6.3 NFPA 72 Documentation and Personnel Qualifications 6.4 Types of Equipment and Circuits: IDC, NAC, SLC and System Architectures 6.5 Signal Priority, Annunciation and Monitoring Integrity 6.6 Primary & Secondary Power Supply Calculations 6.7 Principles of Electricity and Notification Circuit Voltage Drop 6.8 Initiating & Notification Circuit Pathways (Class A, B, N, X) 6.9 Pathway Survivability, Shared Pathways and Circuit Separation
7 Chapter 7: Initiating Devices and Detection
7.1 Smoke, Heat & Flame Detection Principles & Spacing Rules 7.2 Gas Detection, Carbon Monoxide Detection and Special-Application Devices 7.3 Detector Selection and Environmental Limits 7.4 Duct Smoke Detectors, HVAC Controls & Specialized Sensors 7.5 Manual Fire Alarm Boxes, Waterflow Switches & Supervisory Initiating Devices 7.6 Sprinkler, Suppression and Releasing Service Interface
8 Chapter 8: Notification Appliances, Emergency Communications and Control Functions
8.1 Audible Notification Requirements & Sound Level Standards 8.2 Visible Notification Spacing, Synchronization & Candela Ratings 8.3 Emergency Communications Systems & Mass Notification Integration 8.4 Emergency Control Functions: Elevators, HVAC, Doors and Egress 8.5 Protected Premises Systems and the Sequence of Operation
9 Chapter 9: Wiring Methods, Supervising Stations and Inspection, Testing and Maintenance
9.1 NEC Article 760 Wiring Methods, Cable Classes & Circuit Protection 9.2 NEC Article 300 Wiring Methods and Installation Workmanship 9.3 Supervising Station Monitoring Systems & Signal Transmission Methods 9.4 Public Emergency Alarm Reporting Systems and Auxiliary Systems 9.5 Periodic Inspection, Testing & Impairment Procedures 9.6 System Acceptance Testing, Commissioning & Maintenance Records
9.2 NEC Article 300 Wiring Methods and Installation Workmanship
Key Takeaways Explain This Topic AI
Cables run through bored holes in wood framing must be at least 1¼ inches from the nearest edge of the member, or protected by a steel plate at least 1/16 inch thick.
Cables run parallel to framing members must be at least 1¼ inches from the nearest edge, or protected by a steel plate at least 1/16 inch thick.
Raceways and cables must be securely fastened and independently supported by the building structure; ceiling grid support wires and other raceways may not be used as support.
Splices and terminations require an enclosure such as a box, conduit body, or listed fitting, accessible after installation.
Openings around penetrations of fire-rated walls, floors and ceilings must be firestopped to maintain the rating, and wiring in ducts and plenums is restricted to methods permitted for those spaces.
Last updated: August 2026
Why This Section Matters
Article 760 tells you which cable to use; Article 300 tells you how to install it. The SFMO's test reference for TFM12 names both. Article 300 is also the source of most workmanship citations on a Texas job, and 28 TAC § 34.618's three staged inspections exist largely to catch Article 300 problems before the ceiling closes.
1. Protection From Physical Damage — the 1¼-Inch Rule
Situation Requirement
Cable through a bored hole in a wood stud, joist or rafter The edge of the hole must be not less than 1¼ in. from the nearest edge of the member; otherwise install a steel plate at least 1/16 in. thick over the area
Cable run parallel to a framing member or furring strip The cable must be not less than 1¼ in. from the nearest edge; otherwise protect with a steel plate at least 1/16 in. thick
Notches in wood members The cable must be protected by a steel plate at least 1/16 in. thick at the notch
Metal framing members Bushings or grommets are required where cables pass through factory or field-cut openings
The number to memorize is 1¼ inches , and the remedy is 1/16-inch steel plate . A drywall screw is roughly 1¼ inches long — which is exactly why the rule exists.
2. Securing and Supporting
- Rule Requirement
- Secure fastening Raceways, cable assemblies, boxes, cabinets and fittings must be securely fastened in place
Independent support Cables and raceways must be supported by the building structure , using dedicated hardware such as J-hooks, bridle rings, or straps
Ceiling support wires Ceiling grid support wires may not be used to support raceways or cables, unless independent support wires are provided and identified as such
Other raceways A raceway may not be used as a means of support for other cables or raceways, except as specifically permitted
Neat and workmanlike Article 760 adds that fire alarm circuits must be installed in a neat and workmanlike manner , with cables supported so the cable is not damaged by normal building use
The most common field violation on a fire alarm job is zip-tying FPL cable to a sprinkler pipe, a ceiling grid wire, or an electrical conduit. All three are improper support.
3. Boxes, Splices and Accessibility
Splices and taps require an enclosure — a box, conduit body, or a listed fitting designed for the purpose.
Enclosures containing splices must remain accessible after installation. A junction box above a hard-lid ceiling with no access panel is a violation.
Unused openings in boxes and enclosures must be closed with listed closures or fittings.
Cables entering enclosures must be secured to the enclosure, and the conductors protected from abrasion.
4. Fire-Rated Assemblies and Firestopping
Openings around electrical penetrations through fire-resistance-rated walls, partitions, floors and ceilings must be firestopped using approved methods to maintain the fire resistance rating . In practice this means a listed firestop system appropriate to the assembly and to the penetrant, installed per its listing.
Related requirements:
Penetrations of smoke barriers must maintain the smoke resistance of the assembly.
Sleeve and annular-space dimensions must match the listed system; oversized sleeves stuffed with mineral wool are not a listed system.
Article 300's spread-of-fire provisions apply equally to power-limited fire alarm cable, which is why the fire alarm contractor — not "the firestop trade" — owns its own penetrations.
5. Ducts, Plenums and Other Air-Handling Spaces
Space What is permitted
Ducts used for dust, loose stock or vapor removal Wiring is generally prohibited except as specifically permitted for equipment within the duct
Ducts and plenums specifically fabricated for environmental air Only the limited wiring methods permitted for those spaces, and only for equipment or devices within the duct — this is why duct smoke detector wiring is carefully restricted
Other spaces used for environmental air (plenums above suspended ceilings) Plenum-rated cable such as FPLP , or approved raceway methods; ordinary FPL is not permitted
Article 760's cable substitution hierarchy fills in the rest: FPLP may be used anywhere FPLR or FPL may be used; FPLR may be used where FPL may be used; CMP may substitute for FPLP. Substitution never runs downward — general-purpose cable never satisfies a riser or plenum requirement.
6. Article 300 and Article 760 Together
- Question Article
- Which cable type may I use here? 760 (with Table 760.154 for substitutions)
How far must I keep power-limited fire alarm cable from a 277 V circuit? 760.136 — at least 2 in. , unless in raceway or separated by a listed barrier
- Must I remove abandoned cable? 760 — accessible portions of abandoned cable must be removed
- How do I protect cable through a stud? 300.4 — 1¼ in. or a 1/16-in. steel plate
May I support cable on the ceiling grid wires? 300.11 — no, unless independent support wires are provided and identified
- Do I need a box at this splice? 300.15 — yes, with an accessible enclosure
- How do I seal this rated-wall penetration? 300.21 — approved firestopping that maintains the rating
May I run FPL through the return plenum? 300.22 and 760 — no; use plenum-rated cable or an approved raceway method
7. Worked Fact Patterns
Pattern A. FPL cable is stapled to the face of a wood stud ¾ inch from the edge, with drywall going on next.
→ Violation of 300.4. Either maintain 1¼ in. from the nearest edge or install a 1/16-in. steel plate to protect the cable from screws.
Pattern B. A crew supports 200 feet of fire alarm cable by looping it over the ceiling grid support wires.
→ Violation of 300.11 and of Article 760's workmanlike-support requirement. Install dedicated J-hooks or bridle rings supported by the building structure, or independent support wires identified for that purpose.
Pattern C. A splice is made inside a ceiling void with a wire nut and electrical tape, no box.
→ Violation of 300.15. Splices require an enclosure — a box, conduit body, or listed fitting — that remains accessible.
Pattern D. FPL cable is run through a return-air plenum above a suspended ceiling.
→ Violation. Plenum spaces require plenum-rated cable such as FPLP , or an approved raceway method under 300.22(C).
Pattern E. A one-hour corridor wall is penetrated with a 4-inch sleeve, and the annular space is packed with fiberglass batt insulation.
→ Violation of 300.21. Firestopping must be an approved method that maintains the fire resistance rating — a listed firestop system, not generic insulation.