Study guide

9.5 Periodic Inspection, Testing & Impairment Procedures

Texas Fire Alarm Installer License Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Texas Insurance Code Chapter 6002 Foundations

1.1 Chapter 6002 Purpose, Scope & Statutory Definitions 1.2 State Preemption and the Limits of Local Regulation 1.3 Commissioner and SFMO Authority; Adopted Standards and Editions 1.4 Activities Not Regulated: The § 6002.155 Exemptions 1.5 Required Device Labels, Listings and Consumer Information

2 Chapter 2: Certificates of Registration and Company Operating Rules

2.1 Registration Certificates: Main Office, Branch Office and Single Station 2.2 Insurance Requirements for Registered Firms 2.3 Business Location, Designated Employee and Vehicle Identification (§ 34.610) 2.4 Ownership Changes, Officer Changes and Revised Certificates

3 Chapter 3: Individual Licenses, Qualifying Tests and Renewal

3.1 The Six Texas Fire Alarm Licenses and What Each May Do 3.2 License Applications, Fingerprinting and Criminal History 3.3 The Qualifying Tests: TFM11, TFM12, TFM13, TFM14 and Their References 3.4 NICET, ESA and Professional Engineer Substitutions 3.5 Fees, the Two-Year Renewal Cycle and Late Renewal 3.6 Training Schools, Instructors and the Residential Technician Course

4 Chapter 4: Texas Field Practice — Installation, Service, Monitoring and Certification

4.1 Sales, Installation and Service Rules (§ 34.616) 4.2 Monitoring Requirements for Registered Firms (§ 34.616(c)) 4.3 The Installation Certificate (SF035) and Its Distribution 4.4 The Three-Stage Installation Inspection (§ 34.618) 4.5 Fire Alarm Plans and Record Drawings (§ 34.619)

5 Chapter 5: Texas Labels, Records and Enforcement

5.1 Installation and Service Labels (§§ 34.620–34.621) 5.2 Inspection/Test, Yellow and Red Labels and Impairment Notice 5.3 The Texas Recordkeeping and Retention Map 5.4 Prohibited Practices, Discipline, Enforcement and Penalties

6 Chapter 6: NFPA 72 Fundamentals, Power, Signals and Pathways

6.1 Identifying the Applicable NFPA Standards for TFM12 6.2 NFPA 72 Scope, Organization & Core Life Safety Definitions 6.3 NFPA 72 Documentation and Personnel Qualifications 6.4 Types of Equipment and Circuits: IDC, NAC, SLC and System Architectures 6.5 Signal Priority, Annunciation and Monitoring Integrity 6.6 Primary & Secondary Power Supply Calculations 6.7 Principles of Electricity and Notification Circuit Voltage Drop 6.8 Initiating & Notification Circuit Pathways (Class A, B, N, X) 6.9 Pathway Survivability, Shared Pathways and Circuit Separation

7 Chapter 7: Initiating Devices and Detection

7.1 Smoke, Heat & Flame Detection Principles & Spacing Rules 7.2 Gas Detection, Carbon Monoxide Detection and Special-Application Devices 7.3 Detector Selection and Environmental Limits 7.4 Duct Smoke Detectors, HVAC Controls & Specialized Sensors 7.5 Manual Fire Alarm Boxes, Waterflow Switches & Supervisory Initiating Devices 7.6 Sprinkler, Suppression and Releasing Service Interface

8 Chapter 8: Notification Appliances, Emergency Communications and Control Functions

8.1 Audible Notification Requirements & Sound Level Standards 8.2 Visible Notification Spacing, Synchronization & Candela Ratings 8.3 Emergency Communications Systems & Mass Notification Integration 8.4 Emergency Control Functions: Elevators, HVAC, Doors and Egress 8.5 Protected Premises Systems and the Sequence of Operation

9 Chapter 9: Wiring Methods, Supervising Stations and Inspection, Testing and Maintenance

9.1 NEC Article 760 Wiring Methods, Cable Classes & Circuit Protection 9.2 NEC Article 300 Wiring Methods and Installation Workmanship 9.3 Supervising Station Monitoring Systems & Signal Transmission Methods 9.4 Public Emergency Alarm Reporting Systems and Auxiliary Systems 9.5 Periodic Inspection, Testing & Impairment Procedures 9.6 System Acceptance Testing, Commissioning & Maintenance Records

9.5 Periodic Inspection, Testing & Impairment Procedures

Key Takeaways Explain This Topic AI

NFPA 72 Chapter 14 (Table 14.4.3.2) establishes mandatory periodic testing frequencies: manual pull stations (annual), smoke detector functional aerosol entry tests (annual), vane-type waterflow switches (semi-annual), and valve tamper supervisory switches (semi-annual).

Smoke detector sensitivity testing must be conducted within 1 year after installation, then alternate years (every 2 years); after two consecutive tests demonstrating stability, the interval may be extended to every 5 years.

Duct smoke detectors require annual functional aerosol testing plus airflow velocity verification (differential pressure measurement via manometer or pitot tube) to ensure the sampling tubes operate within listed manufacturer parameters.

Secondary power supply batteries require monthly terminal float voltage inspection and semi-annual load testing (conductance testing or 30-minute discharge testing).

Under NFPA 72 and Texas 28 TAC § 34.616, if a fire alarm system is impaired for more than 4 hours in a 24-hour period, an Impairment Coordinator must be designated, mandatory notifications made to the AHJ and monitoring station, and mitigating measures (such as a continuous fire watch) implemented.

Last updated: August 2026

Periodic Inspection, Testing & Impairment Procedures

A fire alarm system provides reliable life safety protection only if every initiating device, notification appliance, power supply, and control interface remains in operational readiness throughout its operational lifespan. NFPA 72 Chapter 14 establishes comprehensive requirements for Inspection, Testing, and Maintenance (ITM) , defining explicit visual inspection schedules and functional testing intervals.

In Texas, registered Alarm Certificate of Registration (ACR) contractors and licensed technicians must strictly observe these ITM schedules and execute the Texas label and notification procedures in 28 TAC §§ 34.621, 34.623 and 34.624 whenever a system is compromised. Mastery of Table 14.4.3.2 frequencies, sensitivity testing rules, and impairment protocols is vital for the PSI TFM11 and TFM12 examinations .

1. Visual Inspection Schedules (NFPA 72 Table 14.3.1)

Visual inspection confirms that equipment is physically intact, free from mechanical damage, unobstructed, properly aligned, and exhibiting normal status indicators: +---------------------------------------------------------------------------------------------------+

  • | NFPA 72 VISUAL INSPECTION FREQUENCY MATRIX |
  • | |
  • | [DAILY] ===> Primary / Secondary Power LEDs, FACP Normal Status Lamp |
  • | [MONTHLY] ===> Sealed Lead-Acid (SLA) Batteries (corrosion, leakage), Transient Protectors|
  • | [SEMI-ANNUAL] ===> Initiating Devices in Harsh Environments, Waterflow & Tamper Switches |
  • | [ANNUAL] ===> 100% of ALL Initiating Devices, Notification Appliances, Control Interfaces|
  • +---------------------------------------------------------------------------------------------------+
  • 2. Functional Testing Schedules (NFPA 72 Table 14.4.3.2)

Functional testing verifies the actual electrical and mechanical operation of devices, circuits, and emergency control functions:

Initiating / Indicating Device Mandatory Testing Frequency Specific Testing Methodology & Performance Criteria

Manual Fire Alarm Boxes Annually Operate 100% of pull stations; verify mechanical action, electrical contact closure, FACP address display, and key/tool reset.

Smoke Detectors (Functional) Annually Aerosol Entry Test: Introduce listed canned smoke/aerosol into sensing chamber to verify smoke entry and alarm initiation. (Magnet testing alone is NOT acceptable for annual functional testing).

Duct Smoke Detectors Annually 1. Functional aerosol test into sampling chamber.; 2. Airflow Verification: Measure differential pressure across sampling tubes using a pitot tube/manometer to confirm velocity is within manufacturer listed range.

Restorable Heat Detectors Annually Apply listed heat source (heat gun/hair dryer) to activate thermal element; test 2 or more detectors per circuit annually until 100% tested over 5 years.

Non-Restorable Fixed-Temp Heat Detectors After 15 Years, then every 5 Years Laboratory sample testing: Remove 2 detectors per 100 and send to testing lab for destructive testing.

Vane-Type Waterflow Switches Semi-Annually Open inspector's test valve; verify alarm initiation at FACP within 90 seconds of water movement.

Valve Tamper Switches Semi-Annually Turn valve handwheel; verify distinct supervisory signal initiates within first 2 revolutions or 1/5th travel from full open.

Audible / Visible Appliances Annually Verify 100% operation, strobe flash synchronization, and audibility sound levels via calibrated SPL meter. +---------------------------------------------------------------------------------------------------+

  • | SPRINKLER WATERFLOW & VALVE TAMPER TIMING RULES |
  • | |
  • | +-------------------------------------------------------------------------------------------+ |
  • | | [VANE-TYPE WATERFLOW SWITCH] |
  • | | - Testing Frequency: SEMI-ANNUAL (via Inspector's Test Valve) | |
  • | | - Maximum Allowable Alarm Activation Time: <= 90 SECONDS | |
  • | | - Signal Classification: ALARM (Non-silenceable general evacuation) | |
  • | +-------------------------------------------------------------------------------------------+ |
  • | |
  • | +-------------------------------------------------------------------------------------------+ |
  • | | [VALVE SUPERVISORY TAMPER SWITCH] |
  • | | - Testing Frequency: SEMI-ANNUAL (Rotate Control Valve Handwheel) | |
  • | | - Activation Threshold: <= 2 REVOLUTIONS of wheel or 1/5th OF TOTAL TRAVEL | |
  • | | - Signal Classification: SUPERVISORY (Non-alarm alert, no general building evacuation) | |
  • | +-------------------------------------------------------------------------------------------+ |
  • +---------------------------------------------------------------------------------------------------+
  • 3. Smoke Detector Sensitivity Testing (NFPA 72 14.4.4.3)

Smoke detector sensitivity naturally drifts over time due to airborne dust accumulation, environmental humidity, and component aging. Excessive sensitivity causes false/nuisance alarms, while reduced sensitivity causes delayed detection during real fires. +---------------------------------------------------------------------------------------------------+

  • | SMOKE DETECTOR SENSITIVITY TESTING TIMELINE & INTERVALS |
  • | |
  • | [INITIAL INSTALLATION] |
  • | | |
  • | v |
  • | [YEAR 1: MANDATORY INITIAL SENSITIVITY TEST] |
  • | - Must test 100% of smoke detectors within 1 year of commissioning |
  • | | |
  • | v |
  • | [YEAR 3: 2nd SENSITIVITY TEST (ALTERNATE YEAR REGIMEN)] |
  • | - Test 100% of smoke detectors 2 years after initial test |
  • | | |
  • | +----------------------------------+----------------------------------+ |
  • | | (If within listed range both times) | (If drifted) |
  • | v v |
  • | [EXTENDED INTERVAL: UP TO EVERY 5 YEARS] [CLEAN / RECALIBRATE] |
  • | - Testing frequency may be extended up to every 5 years - Clean chamber or replace|
  • +---------------------------------------------------------------------------------------------------+

Permissible Sensitivity Testing Methods:

Calibrated test method using manufacturer-specified field test equipment.

Manufacturer-calibrated sensitivity test instruments.

Panel-based automatic software sensitivity reporting (intelligent analog addressable FACPs with drift compensation readout).

Listed control equipment calibrated sensitivity testing features.

Warning

Prohibition of Uncalibrated Testing: Using unmetered aerosol sprays or handheld magnets is strictly prohibited for verifying smoke detector sensitivity. Magnet tests only verify that internal circuitry can switch states; they do not measure optical obscuration sensitivity.

4. Secondary Power Supply Battery Testing

Sealed Lead-Acid (SLA) batteries provide emergency standby power during utility power outages. NFPA 72 Table 14.4.3.2 specifies strict battery diagnostic testing: +---------------------------------------------------------------------------------------------------+

  • | SLA BATTERY DIAGNOSTIC TESTING INTERVALS |
  • | |
  • | [MONTHLY] ===> Check terminal float voltage (Nominal 27.2V–27.6V for 24V system) |
  • | [SEMI-ANNUALLY] ===> Conductance Load Test or 30-Minute AC Discharge Test |
  • | [ANNUALLY] ===> Full load discharge test (Standby current + Full Alarm load duration) |
  • | [REPLACEMENT] ===> Replace battery when capacity drops below 80% of rated Ah, or at 3-5 yrs |
  • +---------------------------------------------------------------------------------------------------+

Conductance Testing: Uses an electronic battery analyzer to measure internal plate resistance (mhos/siemens) without discharging the battery.

Load Discharge Test: Simulates total loss of AC power. A 24V battery set is tested under full supervisory load for 24 hours (or 60 hours for proprietary/high-hazard) followed by a 5-minute (or 15-minute for voice evacuation) full alarm load. Any battery providing less than 80% of rated ampere-hour capacity must be immediately replaced.

5. Impairment Protocols & Fire Watch Procedures

Whenever a fire alarm system or critical life safety component becomes inoperable (due to planned maintenance, renovations, lightning strikes, or catastrophic hardware failure), an Impairment Procedure must be executed under NFPA 72 Chapters 10 and 14 and, in Texas, 28 TAC §§ 34.623–34.624 . +---------------------------------------------------------------------------------------------------+

  • | STATUTORY IMPAIRMENT PROTOCOL WORKFLOW |
  • | |
  • | [STEP 1: DESIGNATE IMPAIRMENT COORDINATOR] |
  • | - Building owner designates Impairment Coordinator (default is building owner) |
  • | | |
  • | v |
  • | [STEP 2: MANDATORY NOTIFICATIONS] |
  • | - Notify Local AHJ (Fire Marshal), Supervising Monitoring Station, Building Occupants & Insurer |
  • | | |
  • | v |
  • | [STEP 3: MITIGATING MEASURES & FIRE WATCH] |
  • | - If impaired > 4 hours in a 24-hour period in an occupied building: MANDATORY FIRE WATCH |
  • | | |
  • | v |
  • | [STEP 4: SYSTEM RESTORATION & RE-LABELING] |
  • | - Perform 100% functional re-test on repaired components, notify all parties, clear labels |
  • +---------------------------------------------------------------------------------------------------+

Core Impairment Rules:

The Impairment Coordinator: The property owner must appoint an Impairment Coordinator. If none is explicitly appointed, the building owner legally assumes this responsibility.

The 4-Hour Rule (Fire Watch): Under NFPA 101, IFC, and NFPA 72, if a fire alarm system is out of service for more than 4 hours in a 24-hour period , the building must either be evacuated or an approved continuous roving Fire Watch established until the system is restored to full service.

Texas SFMO yellow / red label execution: If a system impairment is identified during inspection or servicing:

Yellow label (28 TAC § 34.623) — system operable but non-compliant: written notice to the owner, occupant or representative and the local AHJ, postmarked, emailed, faxed or hand delivered within five business days of attaching the label.

Red label (28 TAC § 34.624) — system inoperable: immediate oral notice to the owner, occupant or representative and the local AHJ, plus written notice emailed, faxed or hand delivered within the next business day . Where the system instead has a fault condition or is impaired from normal operation, written notice is due within three business days .

Clearing either label: attach a service label certifying the corrections, mark the removed label's color and date on it (§ 34.621(b)), and notify the local AHJ within five business days of removal.