Study guide

6.4 Mechanical Ventilation Rates, Air Equipment, and Refrigeration Machinery Rooms

Texas Air Conditioning and Refrigeration Contractor License Exam Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

About the Texas ACR Contractor Exam Open-Book Strategy and the Approved Reference Library

2 Chapter 1: Texas Licensing Laws & TDLR Regulations

1.1 TDLR Licensing Framework, Class A vs Class B Scope, and Technician Registration 1.2 Insurance, Financial Responsibility, Display of License, and Advertising Rules 1.3 TDLR Enforcement, Violations, Administrative Penalties, and Continuing Education

3 Chapter 2: Thermodynamics & Core HVAC Principles

2.1 Heat Transfer Principles: Conduction, Convection, Radiation, and Sensible vs Latent Heat 2.2 Temperature, Pressure, Enthalpy, and the Pressure-Temperature Relationship 2.3 System Airflow Fundamentals, CFM Calculations, and Total External Static Pressure

4 Chapter 3: Load Calculations & System Sizing (Manual J, S, D)

3.1 ACCA Manual J Load Calculations: Heat Gain, Heat Loss, and Building Envelope Factors 3.2 ACCA Manual S Equipment Selection and Manual D Duct Design Principles 3.3 Texas Climate Design Conditions, Solar Gain, and Infiltration Adjustments

5 Chapter 4: Refrigerants, EPA Section 608 & Low-GWP A2L Transition

4.1 Refrigerant Classifications (CFC, HCFC, HFC, HFO) and EPA Section 608 Rules 4.2 AIM Act Phasedown, Next-Gen Low-GWP Refrigerants (R-454B, R-32), and A2L Safety Rules 4.3 Refrigerant Recovery, Recycling, Reclamation, Leak Repair Thresholds, and Evacuation

6 Chapter 5: Refrigeration Cycle & Core System Components

5.1 The Vapor-Compression Refrigeration Cycle and System Component States 5.2 Compressors: Types (Scroll, Reciprocating, Rotary), Maintenance, and Failure Modes 5.3 Condensers, Evaporators, and Expansion Devices (TXV, EEV, Fixed Orifice) 5.4 Service Valves, Filter-Driers, Sight Glasses, and Solenoid & Check Valves

7 Chapter 6: Air Distribution, Ductwork & Indoor Air Quality

6.1 Duct Layouts, Materials, Insulation, Duct Sealing, and Friction Loss 6.2 Air Balancing, Blower Performance Curves, and Air Distribution Fittings 6.3 Indoor Air Quality (IAQ): Ventilation, Filtration, Humidity Control, and ASHRAE 62.2 6.4 Mechanical Ventilation Rates, Air Equipment, and Refrigeration Machinery Rooms

8 Chapter 7: Heating Systems, Gas Controls & Venting

7.1 Gas-Fired Heating: Natural Gas, LP, Burners, Heat Exchangers, and Gas Piping 7.2 Gas Furnace Venting Categories, Draft Hoods, and Combustion Air Requirements 7.3 Electric Resistance Heating and Heat Pump Operation in Heating & Defrost Modes 7.4 Clothes Dryer Exhaust and Product-Conveying Duct Systems 7.5 Combustion Testing and Analysis: CO, Oxygen, Stack Temperature, Draft, and Efficiency

9 Chapter 8: Electrical Systems, Controls & Troubleshooting

8.1 HVAC Electrical Fundamentals: Voltage, Current, Resistance, and Transformer Sizing 8.2 Electric Motors: PSC, ECM, Capacitor Sizing, Relays, Contactors, and Starters 8.3 Schematics Reading, Control Circuits (24V), Thermostats, and Diagnostic Sequence 8.4 Pressure and Safety Controls: High/Low Pressure, Oil Safety, Freeze Protection, and Head Pressure Control

10 Chapter 9: Mechanical Codes & Texas Local Standards (IMC, IFGC & UMC)

9.1 International Mechanical Code (IMC): Equipment Clearances, Access, and Support 9.2 International Fuel Gas Code (IFGC): Pipe Sizing, Materials, Purging, and Testing 9.3 Condensate Drain Piping, Trap Sizing, Secondary Drain Protection, and Auxiliary Pans 9.4 Uniform Mechanical Code vs. International Mechanical Code: Adoption, Differences, and Locating Code Answers 9.5 Refrigerant Line Sizing, Piping Materials, Brazing, Oil Return, and Pipe Support

11 Chapter 10: Commercial Refrigeration & Process Cooling Systems

10.1 Commercial Refrigeration Systems: Walk-in Freezers, Coolers, and Multi-Compressor Racks 10.2 Defrost Systems: Electric, Hot Gas, Off-Cycle, and Evaporator Pressure Regulators (EPR) 10.3 Hydronic Chilled Water Systems, Boilers, and Process Cooling Fundamentals

12 Chapter 11: Jobsite Safety, OSHA Compliance & Business Practice

11.1 OSHA Safety Standards: Fall Protection, Personal Protective Equipment (PPE), and Ladder Safety 11.2 Lockout/Tagout (LOTO), Electrical Safety, High-Pressure Gas Cylinder Handling 11.3 Contractor Business Operations: Contracts, Lien Laws, Permits, Inspections, and Warranties 11.4 OSHA 29 CFR Part 1904: Recording and Reporting Occupational Injuries and Illnesses

6.4 Mechanical Ventilation Rates, Air Equipment, and Refrigeration Machinery Rooms

Key Takeaways Explain This Topic AI

IMC 403.3.1.1 outdoor air is additive: Vbz = Rp x Pz + Ra x Az. A 2,000 ft2 restaurant dining room at the default 70 people per 1,000 ft2 needs 7.5 x 140 + 0.18 x 2,000 = 1,410 cfm.

IMC 401.4 requires outdoor-air intakes not less than 10 feet from lot lines or buildings on the same lot, 10 feet horizontally from contaminant sources, and 3 feet below any contaminant source located within 10 feet.

The exhaust column of IMC Table 403.3.1.1 lists 0.70 cfm/ft2 for commercial cooking spaces, 0.75 cfm/ft2 for enclosed parking garages and auto repair rooms, and 0.60 cfm/ft2 for beauty and nail salons.

IMC 1105.6.3.2, Equation 11-2, sets machinery-room emergency purge at Q = 100 x the square root of G, where G is the design refrigerant mass in pounds of the largest system in the room.

In ASHRAE 34 safety groups the letter is toxicity (A = OEL at or above 400 ppm, B = below 400 ppm) and the number is flammability, with subclass 2L reserved for class 2 refrigerants whose burning velocity is 10 cm/s or less.

Last updated: August 2026

Part A: Air Equipment — Outdoor Air Under IMC Chapter 4

The International Mechanical Code (IMC) , 2021 edition, is one of the reference books you carry into the Texas Department of Licensing and Regulation (TDLR) Air Conditioning and Refrigeration (ACR) exam, and "Air Equipment" ventilation items are written to be answered out of it. Section 403.3.1.1 sets the outdoor airflow rate for every occupancy except low-rise dwellings, and it is a two-part calculation, not a single number:

V b z = R p × P z + R a × A z V_{bz} = R_p \times P_z + R_a \times A_z V b z ​ = R p ​ × P z ​ + R a ​ × A z ​

V b z V_{bz} V b z ​ is the breathing-zone outdoor airflow in cubic feet per minute (cfm), R p R_p R p ​ is the people rate in cfm per person, P z P_z P z ​ is the zone population, R a R_a R a ​ is the area rate in cfm per square foot, and A z A_z A z ​ is the zone floor area. Both halves are always added; the most common wrong answer computes only the people component. Where the design population is not otherwise established, the default occupant density in the same table — people per 1,000 square feet — turns the floor plan into a population.

Occupancy (IMC Table 403.3.1.1) Default density (people/1,000 ft2) People rate (cfm/person) Area rate (cfm/ft2) Exhaust rate (cfm/ft2)

  • Restaurant dining rooms 70 7.5 0.18 —
  • Cafeteria, fast-food dining 100 7.5 0.18 —
  • Classrooms (age 9 and older) 35 10 0.12 —
  • Classrooms (ages 5–8) 25 10 0.12 —
  • Office spaces 5 5 0.06 —
  • Conference and meeting rooms 50 5 0.06 —
  • Kitchens (commercial cooking) 20 7.5 0.12 0.70
  • Enclosed parking garages, auto repair rooms — — — 0.75
  • Beauty and nail salons 25 20 0.12 0.60
  • Worked example: a 1,800 ft2 dining room

Population: P z = 1,800 × 70 / 1,000 = 126 P_z = 1{,}800 \times 70 / 1{,}000 = 126 P z ​ = 1 , 800 × 70/1 , 000 = 126 people. People component: 7.5 × 126 = 945 7.5 \times 126 = 945 7.5 × 126 = 945 cfm. Area component: 0.18 × 1,800 = 324 0.18 \times 1{,}800 = 324 0.18 × 1 , 800 = 324 cfm. Required breathing-zone outdoor air: 1,269 cfm .

Same math on a 900 ft2 classroom for students age 9 and older: P z = 900 × 35 / 1,000 = 31.5 P_z = 900 \times 35/1{,}000 = 31.5 P z ​ = 900 × 35/1 , 000 = 31.5 , rounded up to 32 occupants; 10 × 32 = 320 10 \times 32 = 320 10 × 32 = 320 plus 0.12 × 900 = 108 0.12 \times 900 = 108 0.12 × 900 = 108 , for 428 cfm . The classroom needs more air per person but less per square foot — the pairing distractors scramble.

Exhaust Requirements and Enclosed Parking Garages

In the 2021 IMC the required exhaust rates for commercial spaces live in the far-right column of that same Table 403.3.1.1, not in a separate table. Toilet rooms break the cfm-per-square-foot pattern and are listed per fixture — 50 or 70 cfm per water closet or urinal for public toilet rooms, 25 or 50 cfm per room for private bathrooms — with footnotes defining which of the paired numbers applies. Exhaust from toilet rooms, kitchens and janitor closets is transfer-and-dump air : it may be made up from adjacent spaces but never recirculated into the occupied building.

Enclosed parking garages get their own section. IMC 404 requires mechanical ventilation of not less than 0.75 cfm per square foot of floor area served in full-on operation, and permits automatic operation on carbon monoxide and nitrogen dioxide detection that cycles the fans down to a standby rate of not less than 0.05 cfm per square foot . On the exam, 0.75 answers "how big is the fan" and 0.05 answers "how far may the controls turn it down."