Study guide
8.4 Pressure and Safety Controls: High/Low Pressure, Oil Safety, Freeze Protection, and Head Pressure Control
Texas Air Conditioning and Refrigeration Contractor License Exam Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
About the Texas ACR Contractor Exam Open-Book Strategy and the Approved Reference Library
2 Chapter 1: Texas Licensing Laws & TDLR Regulations
1.1 TDLR Licensing Framework, Class A vs Class B Scope, and Technician Registration 1.2 Insurance, Financial Responsibility, Display of License, and Advertising Rules 1.3 TDLR Enforcement, Violations, Administrative Penalties, and Continuing Education
3 Chapter 2: Thermodynamics & Core HVAC Principles
2.1 Heat Transfer Principles: Conduction, Convection, Radiation, and Sensible vs Latent Heat 2.2 Temperature, Pressure, Enthalpy, and the Pressure-Temperature Relationship 2.3 System Airflow Fundamentals, CFM Calculations, and Total External Static Pressure
4 Chapter 3: Load Calculations & System Sizing (Manual J, S, D)
3.1 ACCA Manual J Load Calculations: Heat Gain, Heat Loss, and Building Envelope Factors 3.2 ACCA Manual S Equipment Selection and Manual D Duct Design Principles 3.3 Texas Climate Design Conditions, Solar Gain, and Infiltration Adjustments
5 Chapter 4: Refrigerants, EPA Section 608 & Low-GWP A2L Transition
4.1 Refrigerant Classifications (CFC, HCFC, HFC, HFO) and EPA Section 608 Rules 4.2 AIM Act Phasedown, Next-Gen Low-GWP Refrigerants (R-454B, R-32), and A2L Safety Rules 4.3 Refrigerant Recovery, Recycling, Reclamation, Leak Repair Thresholds, and Evacuation
6 Chapter 5: Refrigeration Cycle & Core System Components
5.1 The Vapor-Compression Refrigeration Cycle and System Component States 5.2 Compressors: Types (Scroll, Reciprocating, Rotary), Maintenance, and Failure Modes 5.3 Condensers, Evaporators, and Expansion Devices (TXV, EEV, Fixed Orifice) 5.4 Service Valves, Filter-Driers, Sight Glasses, and Solenoid & Check Valves
7 Chapter 6: Air Distribution, Ductwork & Indoor Air Quality
6.1 Duct Layouts, Materials, Insulation, Duct Sealing, and Friction Loss 6.2 Air Balancing, Blower Performance Curves, and Air Distribution Fittings 6.3 Indoor Air Quality (IAQ): Ventilation, Filtration, Humidity Control, and ASHRAE 62.2 6.4 Mechanical Ventilation Rates, Air Equipment, and Refrigeration Machinery Rooms
8 Chapter 7: Heating Systems, Gas Controls & Venting
7.1 Gas-Fired Heating: Natural Gas, LP, Burners, Heat Exchangers, and Gas Piping 7.2 Gas Furnace Venting Categories, Draft Hoods, and Combustion Air Requirements 7.3 Electric Resistance Heating and Heat Pump Operation in Heating & Defrost Modes 7.4 Clothes Dryer Exhaust and Product-Conveying Duct Systems 7.5 Combustion Testing and Analysis: CO, Oxygen, Stack Temperature, Draft, and Efficiency
9 Chapter 8: Electrical Systems, Controls & Troubleshooting
8.1 HVAC Electrical Fundamentals: Voltage, Current, Resistance, and Transformer Sizing 8.2 Electric Motors: PSC, ECM, Capacitor Sizing, Relays, Contactors, and Starters 8.3 Schematics Reading, Control Circuits (24V), Thermostats, and Diagnostic Sequence 8.4 Pressure and Safety Controls: High/Low Pressure, Oil Safety, Freeze Protection, and Head Pressure Control
10 Chapter 9: Mechanical Codes & Texas Local Standards (IMC, IFGC & UMC)
9.1 International Mechanical Code (IMC): Equipment Clearances, Access, and Support 9.2 International Fuel Gas Code (IFGC): Pipe Sizing, Materials, Purging, and Testing 9.3 Condensate Drain Piping, Trap Sizing, Secondary Drain Protection, and Auxiliary Pans 9.4 Uniform Mechanical Code vs. International Mechanical Code: Adoption, Differences, and Locating Code Answers 9.5 Refrigerant Line Sizing, Piping Materials, Brazing, Oil Return, and Pipe Support
11 Chapter 10: Commercial Refrigeration & Process Cooling Systems
10.1 Commercial Refrigeration Systems: Walk-in Freezers, Coolers, and Multi-Compressor Racks 10.2 Defrost Systems: Electric, Hot Gas, Off-Cycle, and Evaporator Pressure Regulators (EPR) 10.3 Hydronic Chilled Water Systems, Boilers, and Process Cooling Fundamentals
12 Chapter 11: Jobsite Safety, OSHA Compliance & Business Practice
11.1 OSHA Safety Standards: Fall Protection, Personal Protective Equipment (PPE), and Ladder Safety 11.2 Lockout/Tagout (LOTO), Electrical Safety, High-Pressure Gas Cylinder Handling 11.3 Contractor Business Operations: Contracts, Lien Laws, Permits, Inspections, and Warranties 11.4 OSHA 29 CFR Part 1904: Recording and Reporting Occupational Injuries and Illnesses
8.4 Pressure and Safety Controls: High/Low Pressure, Oil Safety, Freeze Protection, and Head Pressure Control
Key Takeaways Explain This Topic AI
Differential is the span between cut-in and cut-out: a low-pressure control set to cut out at 20 psig with a 30 psi differential cuts back in at 50 psig, while a high-pressure control cuts out on rising pressure and cuts in at cut-out minus differential.
Net oil pressure equals oil pump discharge pressure minus crankcase (suction) pressure; mechanical oil safety controls trip when net oil pressure stays below roughly 9 psid for the control's time delay - 45, 90, or 120 second versions are standard - and require manual reset.
Residential R-410A high-pressure switches commonly open between 590 and 650 psig and reset near 420-450 psig; R-22 and R-404A equipment cuts out several hundred psi lower, so always take the setting from the data plate or manufacturer literature.
A loss-of-charge switch is a liquid-line device tripping near 5-20 psig that only detects a nearly empty system; it is not interchangeable with a suction low-pressure control, because a heat pump in heating mode runs low suction normally.
A freezestat uses a 20-foot capillary that responds to the coldest 8-12 inch segment along its length, is typically set near 36-38 degrees F, is manual reset, and cannot be reset until the sensed temperature rises about 5 degrees F above setpoint.
Last updated: August 2026
Cut-in, cut-out, and differential - the two settings behind every pressure control
Every pressure control, mechanical or electronic, is defined by two numbers. Cut-out is the pressure at which the contacts open. Cut-in is the pressure at which they close again. The differential is the span between them:
D i f f e r e n t i a l = C u t i n − C u t o u t Differential = Cut_{in} - Cut_{out} D i ff ere n t ia l = C u t in − C u t o u t
The direction matters and it is the single most common source of wrong answers. A low-pressure control opens on falling pressure at the cut-out setting and closes on rising pressure at cut-out plus differential. A high-pressure control opens on rising pressure at cut-out and closes on falling pressure at cut-out minus differential.
Worked example. A walk-in cooler's low-pressure control is set for a 20 psig cut-out with a 30 psi differential. The compressor runs until suction falls to 20 psig, then stops. It restarts only after suction climbs back to 20 + 30 = 50 20 + 30 = 50 20 + 30 = 50 psig. Convert both numbers to saturation temperature on the pressure-temperature chart for the actual refrigerant in the system, and you have the coil temperature the control is really enforcing.
Most mechanical controls give you a range (or cut-out) scale and a separate differential scale, and the third number is whatever the arithmetic makes it. Set the differential too narrow and the compressor short-cycles; set it too wide on a refrigeration application and the box temperature swings.