Study guide

Open-Book Strategy and the Approved Reference Library

Texas Air Conditioning and Refrigeration Contractor License Exam Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

About the Texas ACR Contractor Exam Open-Book Strategy and the Approved Reference Library

2 Chapter 1: Texas Licensing Laws & TDLR Regulations

1.1 TDLR Licensing Framework, Class A vs Class B Scope, and Technician Registration 1.2 Insurance, Financial Responsibility, Display of License, and Advertising Rules 1.3 TDLR Enforcement, Violations, Administrative Penalties, and Continuing Education

3 Chapter 2: Thermodynamics & Core HVAC Principles

2.1 Heat Transfer Principles: Conduction, Convection, Radiation, and Sensible vs Latent Heat 2.2 Temperature, Pressure, Enthalpy, and the Pressure-Temperature Relationship 2.3 System Airflow Fundamentals, CFM Calculations, and Total External Static Pressure

4 Chapter 3: Load Calculations & System Sizing (Manual J, S, D)

3.1 ACCA Manual J Load Calculations: Heat Gain, Heat Loss, and Building Envelope Factors 3.2 ACCA Manual S Equipment Selection and Manual D Duct Design Principles 3.3 Texas Climate Design Conditions, Solar Gain, and Infiltration Adjustments

5 Chapter 4: Refrigerants, EPA Section 608 & Low-GWP A2L Transition

4.1 Refrigerant Classifications (CFC, HCFC, HFC, HFO) and EPA Section 608 Rules 4.2 AIM Act Phasedown, Next-Gen Low-GWP Refrigerants (R-454B, R-32), and A2L Safety Rules 4.3 Refrigerant Recovery, Recycling, Reclamation, Leak Repair Thresholds, and Evacuation

6 Chapter 5: Refrigeration Cycle & Core System Components

5.1 The Vapor-Compression Refrigeration Cycle and System Component States 5.2 Compressors: Types (Scroll, Reciprocating, Rotary), Maintenance, and Failure Modes 5.3 Condensers, Evaporators, and Expansion Devices (TXV, EEV, Fixed Orifice) 5.4 Service Valves, Filter-Driers, Sight Glasses, and Solenoid & Check Valves

7 Chapter 6: Air Distribution, Ductwork & Indoor Air Quality

6.1 Duct Layouts, Materials, Insulation, Duct Sealing, and Friction Loss 6.2 Air Balancing, Blower Performance Curves, and Air Distribution Fittings 6.3 Indoor Air Quality (IAQ): Ventilation, Filtration, Humidity Control, and ASHRAE 62.2 6.4 Mechanical Ventilation Rates, Air Equipment, and Refrigeration Machinery Rooms

8 Chapter 7: Heating Systems, Gas Controls & Venting

7.1 Gas-Fired Heating: Natural Gas, LP, Burners, Heat Exchangers, and Gas Piping 7.2 Gas Furnace Venting Categories, Draft Hoods, and Combustion Air Requirements 7.3 Electric Resistance Heating and Heat Pump Operation in Heating & Defrost Modes 7.4 Clothes Dryer Exhaust and Product-Conveying Duct Systems 7.5 Combustion Testing and Analysis: CO, Oxygen, Stack Temperature, Draft, and Efficiency

9 Chapter 8: Electrical Systems, Controls & Troubleshooting

8.1 HVAC Electrical Fundamentals: Voltage, Current, Resistance, and Transformer Sizing 8.2 Electric Motors: PSC, ECM, Capacitor Sizing, Relays, Contactors, and Starters 8.3 Schematics Reading, Control Circuits (24V), Thermostats, and Diagnostic Sequence 8.4 Pressure and Safety Controls: High/Low Pressure, Oil Safety, Freeze Protection, and Head Pressure Control

10 Chapter 9: Mechanical Codes & Texas Local Standards (IMC, IFGC & UMC)

9.1 International Mechanical Code (IMC): Equipment Clearances, Access, and Support 9.2 International Fuel Gas Code (IFGC): Pipe Sizing, Materials, Purging, and Testing 9.3 Condensate Drain Piping, Trap Sizing, Secondary Drain Protection, and Auxiliary Pans 9.4 Uniform Mechanical Code vs. International Mechanical Code: Adoption, Differences, and Locating Code Answers 9.5 Refrigerant Line Sizing, Piping Materials, Brazing, Oil Return, and Pipe Support

11 Chapter 10: Commercial Refrigeration & Process Cooling Systems

10.1 Commercial Refrigeration Systems: Walk-in Freezers, Coolers, and Multi-Compressor Racks 10.2 Defrost Systems: Electric, Hot Gas, Off-Cycle, and Evaporator Pressure Regulators (EPR) 10.3 Hydronic Chilled Water Systems, Boilers, and Process Cooling Fundamentals

12 Chapter 11: Jobsite Safety, OSHA Compliance & Business Practice

11.1 OSHA Safety Standards: Fall Protection, Personal Protective Equipment (PPE), and Ladder Safety 11.2 Lockout/Tagout (LOTO), Electrical Safety, High-Pressure Gas Cylinder Handling 11.3 Contractor Business Operations: Contracts, Lien Laws, Permits, Inspections, and Warranties 11.4 OSHA 29 CFR Part 1904: Recording and Reporting Occupational Injuries and Illnesses

Open-Book Strategy and the Approved Reference Library

Key Takeaways Explain This Topic AI

All Texas ACR examinations are open book; candidates bring their own references from the PSI approved list and may not write, highlight or mark them during the session.

Code questions are graded only against the listed edition — the 2021 IMC, IFGC and UMC now, and the 2024 editions effective September 1, 2026 — while non-code references may be answered from later editions.

ACCA Manual J (8th ed., v2.50, 2016), Manual S (2014) and Manual D (2014) are approved for the Environmental Air Class A and Class B examinations only.

Reference books may be tabbed with permanent index tabs only; post-it, temporary, homemade or DIY tabs can cost a candidate the exam fee and force a rebooked appointment at their own expense.

A Class A exam allows 230 minutes for 120 scored items — roughly 1.9 minutes each — so most items must be answered from knowledge and only flagged items looked up.

Last updated: August 2026

Open-Book Strategy and the Approved Reference Library

Quick Answer: Every Texas ACR contractor examination is open book . You bring your own references from a fixed approved list, pre-highlighted and tabbed with permanent index tabs only. That changes what studying means: with roughly 1.9 minutes per item on a Class A exam, you are being graded on how fast you can find an answer, not on how much you memorized.

Open Book Is Not Easy Book

An open-book format removes the recall failure mode and replaces it with a timing failure mode. Every one of the 120 scored items on a Class A exam is answerable from books sitting on the desk in front of you. Candidates still fail — because they burn nine minutes hunting a gas-pipe sizing table and then run out of clock with fifteen items untouched.

So invert your study plan. Instead of "learn the code," practice " locate the code." A candidate who can turn to the duct-construction requirements in twenty seconds is worth more points than one who half-remembers them and then reads the whole chapter to be sure.

Two instructions printed in the Candidate Information Bulletin shape every lookup you will make:

"Do not consider code exceptions unless the test question specifically directs you to consider them." Read the base rule, answer the base rule, stop. Chasing exceptions is the most common way candidates lose time on code items.

"Except for Code books, you can base your answers on later editions of references as they become available. For Code questions, the examinations will be based only on the edition of the Code book that is listed." Non-code references are edition-forgiving. Code books are not.

The Approved Reference Library

You are responsible for bringing your own copies. Everything below may be bought from the publisher or a bookstore, or downloaded and spiral-bound or three-hole-punched into a binder.

  • Reference Edition Subject areas it answers Which exams
  • Texas Occupations Code, Chapter 1302 (ACR Contractors License Law) current Texas Laws and Rules All

16 Texas Administrative Code, Chapter 75 (ACR Rules) current Texas Laws and Rules; Equipment Requirements → HVACR Codes All

OSHA 29 CFR Part 1904, Recording and Reporting Occupational Injuries and Illnesses current Safety All

Uniform Mechanical Code (UMC) , IAPMO 2021 Ventilation; Venting; Air Distribution; Combustion Air; HVAC(R) Systems; Piping All

International Mechanical Code (IMC) , ICC 2021 The ICC-family counterpart to the UMC, same subject areas All

International Fuel Gas Code (IFGC) , ICC 2021 Combustion Air; Venting; Piping (gas); Equipment Requirements All

Modern Refrigeration and Air Conditioning (Althouse, Turnquist et al., Goodheart-Willcox) 22nd ed., 2025 Refrigeration Principles; Basic Refrigeration Components; Controls; Service; Testing All

ADI Duct Size Calculator (Air Distribution Institute) current Air Distribution → Duct Sizing, friction rate All

ACCA Manual J – Residential Load Calculation 8th ed., v2.50, 2016 Equipment Requirements and Design → Heat Loads Environmental Air only

ACCA Manual S – Residential Equipment Selection 2014 Equipment Requirements and Design → Sensible and Latent Capacities Environmental Air only

ACCA Manual D – Residential Duct Systems 2014 Air Distribution → Duct Sizing, Duct Installation Environmental Air only

Note the last three rows. Manual J, Manual S and Manual D are approved for the Environmental Air Class A and Class B examinations only. A Commercial Refrigeration candidate who spends study money and tab time on the ACCA manuals has prepared with books they will not be permitted to open — and, worse, has probably shortchanged Modern Refrigeration and Air Conditioning , which is the technical spine of that exam. The Certified Technician outline even points candidates to one specific page of it: the pressure/temperature chart on page 1309 of the 22nd edition.