Study guide
9.5 Refrigerant Line Sizing, Piping Materials, Brazing, Oil Return, and Pipe Support
Texas Air Conditioning and Refrigeration Contractor License Exam Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
About the Texas ACR Contractor Exam Open-Book Strategy and the Approved Reference Library
2 Chapter 1: Texas Licensing Laws & TDLR Regulations
1.1 TDLR Licensing Framework, Class A vs Class B Scope, and Technician Registration 1.2 Insurance, Financial Responsibility, Display of License, and Advertising Rules 1.3 TDLR Enforcement, Violations, Administrative Penalties, and Continuing Education
3 Chapter 2: Thermodynamics & Core HVAC Principles
2.1 Heat Transfer Principles: Conduction, Convection, Radiation, and Sensible vs Latent Heat 2.2 Temperature, Pressure, Enthalpy, and the Pressure-Temperature Relationship 2.3 System Airflow Fundamentals, CFM Calculations, and Total External Static Pressure
4 Chapter 3: Load Calculations & System Sizing (Manual J, S, D)
3.1 ACCA Manual J Load Calculations: Heat Gain, Heat Loss, and Building Envelope Factors 3.2 ACCA Manual S Equipment Selection and Manual D Duct Design Principles 3.3 Texas Climate Design Conditions, Solar Gain, and Infiltration Adjustments
5 Chapter 4: Refrigerants, EPA Section 608 & Low-GWP A2L Transition
4.1 Refrigerant Classifications (CFC, HCFC, HFC, HFO) and EPA Section 608 Rules 4.2 AIM Act Phasedown, Next-Gen Low-GWP Refrigerants (R-454B, R-32), and A2L Safety Rules 4.3 Refrigerant Recovery, Recycling, Reclamation, Leak Repair Thresholds, and Evacuation
6 Chapter 5: Refrigeration Cycle & Core System Components
5.1 The Vapor-Compression Refrigeration Cycle and System Component States 5.2 Compressors: Types (Scroll, Reciprocating, Rotary), Maintenance, and Failure Modes 5.3 Condensers, Evaporators, and Expansion Devices (TXV, EEV, Fixed Orifice) 5.4 Service Valves, Filter-Driers, Sight Glasses, and Solenoid & Check Valves
7 Chapter 6: Air Distribution, Ductwork & Indoor Air Quality
6.1 Duct Layouts, Materials, Insulation, Duct Sealing, and Friction Loss 6.2 Air Balancing, Blower Performance Curves, and Air Distribution Fittings 6.3 Indoor Air Quality (IAQ): Ventilation, Filtration, Humidity Control, and ASHRAE 62.2 6.4 Mechanical Ventilation Rates, Air Equipment, and Refrigeration Machinery Rooms
8 Chapter 7: Heating Systems, Gas Controls & Venting
7.1 Gas-Fired Heating: Natural Gas, LP, Burners, Heat Exchangers, and Gas Piping 7.2 Gas Furnace Venting Categories, Draft Hoods, and Combustion Air Requirements 7.3 Electric Resistance Heating and Heat Pump Operation in Heating & Defrost Modes 7.4 Clothes Dryer Exhaust and Product-Conveying Duct Systems 7.5 Combustion Testing and Analysis: CO, Oxygen, Stack Temperature, Draft, and Efficiency
9 Chapter 8: Electrical Systems, Controls & Troubleshooting
8.1 HVAC Electrical Fundamentals: Voltage, Current, Resistance, and Transformer Sizing 8.2 Electric Motors: PSC, ECM, Capacitor Sizing, Relays, Contactors, and Starters 8.3 Schematics Reading, Control Circuits (24V), Thermostats, and Diagnostic Sequence 8.4 Pressure and Safety Controls: High/Low Pressure, Oil Safety, Freeze Protection, and Head Pressure Control
10 Chapter 9: Mechanical Codes & Texas Local Standards (IMC, IFGC & UMC)
9.1 International Mechanical Code (IMC): Equipment Clearances, Access, and Support 9.2 International Fuel Gas Code (IFGC): Pipe Sizing, Materials, Purging, and Testing 9.3 Condensate Drain Piping, Trap Sizing, Secondary Drain Protection, and Auxiliary Pans 9.4 Uniform Mechanical Code vs. International Mechanical Code: Adoption, Differences, and Locating Code Answers 9.5 Refrigerant Line Sizing, Piping Materials, Brazing, Oil Return, and Pipe Support
11 Chapter 10: Commercial Refrigeration & Process Cooling Systems
10.1 Commercial Refrigeration Systems: Walk-in Freezers, Coolers, and Multi-Compressor Racks 10.2 Defrost Systems: Electric, Hot Gas, Off-Cycle, and Evaporator Pressure Regulators (EPR) 10.3 Hydronic Chilled Water Systems, Boilers, and Process Cooling Fundamentals
12 Chapter 11: Jobsite Safety, OSHA Compliance & Business Practice
11.1 OSHA Safety Standards: Fall Protection, Personal Protective Equipment (PPE), and Ladder Safety 11.2 Lockout/Tagout (LOTO), Electrical Safety, High-Pressure Gas Cylinder Handling 11.3 Contractor Business Operations: Contracts, Lien Laws, Permits, Inspections, and Warranties 11.4 OSHA 29 CFR Part 1904: Recording and Reporting Occupational Injuries and Illnesses
9.5 Refrigerant Line Sizing, Piping Materials, Brazing, Oil Return, and Pipe Support
Key Takeaways Explain This Topic AI
ACR tube to ASTM B280 is specified by outside diameter and ships nitrogen-charged and capped, while plumbing Type L to ASTM B88 is specified by nominal size whose outside diameter is 1/8 inch larger.
IMC Table 305.4 requires copper or copper-alloy tubing to be supported at intervals not exceeding 8 feet horizontally and 10 feet vertically; copper pipe is 12 feet horizontal and 10 feet vertical.
IMC Section 1110.3 permits only oxygen-free nitrogen, helium or argon as field test gases and prohibits oxygen, air and combustible gases as a test medium.
IMC Section 1108.3.1 requires brazed refrigerant joints to be purged and filled with an inert gas (oxygen-free nitrogen, helium or argon), pre-purged with five volume changes at a minimum 100 feet per minute and held between 1.0 and 3.0 psi during brazing, which prevents cupric oxide scale.
Suction and hot-gas lines must hold a minimum velocity for oil return - published minimums run about 500 to 750 feet per minute horizontal and 1,000 to 1,500 feet per minute in vertical risers, with the equipment manufacturer's line-sizing table governing.
Last updated: August 2026
ACR Tube Is Not Plumbing Tube
Refrigerant lines are run in ACR tube — air conditioning and refrigeration tube manufactured to ASTM B280 . Two properties define it. First, it is cleaned, dehydrated, capped and shipped charged with nitrogen , so the bore arrives free of the oil films, moisture and oxides that would poison a sealed system. Second, and the point exam writers love, ACR tube is specified by outside diameter (OD) . A "7/8-inch" refrigerant line is 7/8 inch across the outside.
Plumbing tube to ASTM B88 — Types K, L and M — is specified by nominal size , and its actual outside diameter is 1/8 inch larger than the nominal call-out. So 3/4-inch nominal Type L plumbing tube measures 7/8 inch OD and is dimensionally the same tube as 7/8-inch ACR. Order or cut from the wrong system and nothing fits.
Type L is the normal wall thickness for field-run refrigerant lines; Type M is thin-wall and is not used for refrigerant service. Joints are made with wrought copper fittings to ASME B16.22 rather than cast fittings, because wrought fittings have a uniform, controlled socket and better fatigue behavior. Use long-radius elbows wherever layout allows — they cost roughly one-third less pressure drop than a standard 90-degree ell of the same size. IMC Section 1107 requires piping material rated for the operating temperature and pressure and compatible with the refrigerant and lubricant, and it prohibits magnesium alloys in contact with halogenated refrigerants.
Three Lines, Three Different Sizing Rules
A split-system line set is not one pipe sized one way. Each leg is sized on its own basis, and mixing the rules is the classic wrong answer.
Liquid line. Sized for pressure drop , with the goal of delivering a solid column of liquid to the metering device. Every psi of drop — friction plus vertical lift — eats subcooling ; lose it all and the line flashes, the sight glass bubbles and the expansion valve starves. Vertical lift alone costs roughly half a psi per foot of rise for common HFC liquids, so a condenser 40 feet above the evaporator can consume most of the available subcooling before friction is counted. Liquid velocity is deliberately kept low; published guidance keeps it under about 300 feet per minute (fpm) on lines with solenoid valves so that closing the solenoid does not produce liquid hammer. The liquid line is always the smallest line in the set.
Suction line. Sized for pressure drop and minimum velocity at the same time . Suction pressure drop is expensive — as a rule of thumb, 1 psi of suction drop costs about 1 percent of capacity and raises power draw — but a suction line sized purely for low drop will be too large to carry oil back. Because some compressor oil circulates with the refrigerant continuously, the vapor has to move fast enough to entrain it. Commonly published minimums are about 500 to 750 fpm in horizontal runs and 1,000 to 1,500 fpm in vertical risers , and sources differ within those ranges; the upper bound of roughly 4,000 fpm is set by noise and erosion. The manufacturer's line-sizing table for the specific equipment and refrigerant governs — these figures are design rules of thumb, not code values.
Hot-gas discharge line. Sized on the same velocity-plus-drop logic as the suction line. Discharge gas is dense, so the line is smaller than the suction line for the same tonnage, but it still has to carry oil up any riser.