Study guide

9.4 Uniform Mechanical Code vs. International Mechanical Code: Adoption, Differences, and Locating Code Answers

Texas Air Conditioning and Refrigeration Contractor License Exam Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

About the Texas ACR Contractor Exam Open-Book Strategy and the Approved Reference Library

2 Chapter 1: Texas Licensing Laws & TDLR Regulations

1.1 TDLR Licensing Framework, Class A vs Class B Scope, and Technician Registration 1.2 Insurance, Financial Responsibility, Display of License, and Advertising Rules 1.3 TDLR Enforcement, Violations, Administrative Penalties, and Continuing Education

3 Chapter 2: Thermodynamics & Core HVAC Principles

2.1 Heat Transfer Principles: Conduction, Convection, Radiation, and Sensible vs Latent Heat 2.2 Temperature, Pressure, Enthalpy, and the Pressure-Temperature Relationship 2.3 System Airflow Fundamentals, CFM Calculations, and Total External Static Pressure

4 Chapter 3: Load Calculations & System Sizing (Manual J, S, D)

3.1 ACCA Manual J Load Calculations: Heat Gain, Heat Loss, and Building Envelope Factors 3.2 ACCA Manual S Equipment Selection and Manual D Duct Design Principles 3.3 Texas Climate Design Conditions, Solar Gain, and Infiltration Adjustments

5 Chapter 4: Refrigerants, EPA Section 608 & Low-GWP A2L Transition

4.1 Refrigerant Classifications (CFC, HCFC, HFC, HFO) and EPA Section 608 Rules 4.2 AIM Act Phasedown, Next-Gen Low-GWP Refrigerants (R-454B, R-32), and A2L Safety Rules 4.3 Refrigerant Recovery, Recycling, Reclamation, Leak Repair Thresholds, and Evacuation

6 Chapter 5: Refrigeration Cycle & Core System Components

5.1 The Vapor-Compression Refrigeration Cycle and System Component States 5.2 Compressors: Types (Scroll, Reciprocating, Rotary), Maintenance, and Failure Modes 5.3 Condensers, Evaporators, and Expansion Devices (TXV, EEV, Fixed Orifice) 5.4 Service Valves, Filter-Driers, Sight Glasses, and Solenoid & Check Valves

7 Chapter 6: Air Distribution, Ductwork & Indoor Air Quality

6.1 Duct Layouts, Materials, Insulation, Duct Sealing, and Friction Loss 6.2 Air Balancing, Blower Performance Curves, and Air Distribution Fittings 6.3 Indoor Air Quality (IAQ): Ventilation, Filtration, Humidity Control, and ASHRAE 62.2 6.4 Mechanical Ventilation Rates, Air Equipment, and Refrigeration Machinery Rooms

8 Chapter 7: Heating Systems, Gas Controls & Venting

7.1 Gas-Fired Heating: Natural Gas, LP, Burners, Heat Exchangers, and Gas Piping 7.2 Gas Furnace Venting Categories, Draft Hoods, and Combustion Air Requirements 7.3 Electric Resistance Heating and Heat Pump Operation in Heating & Defrost Modes 7.4 Clothes Dryer Exhaust and Product-Conveying Duct Systems 7.5 Combustion Testing and Analysis: CO, Oxygen, Stack Temperature, Draft, and Efficiency

9 Chapter 8: Electrical Systems, Controls & Troubleshooting

8.1 HVAC Electrical Fundamentals: Voltage, Current, Resistance, and Transformer Sizing 8.2 Electric Motors: PSC, ECM, Capacitor Sizing, Relays, Contactors, and Starters 8.3 Schematics Reading, Control Circuits (24V), Thermostats, and Diagnostic Sequence 8.4 Pressure and Safety Controls: High/Low Pressure, Oil Safety, Freeze Protection, and Head Pressure Control

10 Chapter 9: Mechanical Codes & Texas Local Standards (IMC, IFGC & UMC)

9.1 International Mechanical Code (IMC): Equipment Clearances, Access, and Support 9.2 International Fuel Gas Code (IFGC): Pipe Sizing, Materials, Purging, and Testing 9.3 Condensate Drain Piping, Trap Sizing, Secondary Drain Protection, and Auxiliary Pans 9.4 Uniform Mechanical Code vs. International Mechanical Code: Adoption, Differences, and Locating Code Answers 9.5 Refrigerant Line Sizing, Piping Materials, Brazing, Oil Return, and Pipe Support

11 Chapter 10: Commercial Refrigeration & Process Cooling Systems

10.1 Commercial Refrigeration Systems: Walk-in Freezers, Coolers, and Multi-Compressor Racks 10.2 Defrost Systems: Electric, Hot Gas, Off-Cycle, and Evaporator Pressure Regulators (EPR) 10.3 Hydronic Chilled Water Systems, Boilers, and Process Cooling Fundamentals

12 Chapter 11: Jobsite Safety, OSHA Compliance & Business Practice

11.1 OSHA Safety Standards: Fall Protection, Personal Protective Equipment (PPE), and Ladder Safety 11.2 Lockout/Tagout (LOTO), Electrical Safety, High-Pressure Gas Cylinder Handling 11.3 Contractor Business Operations: Contracts, Lien Laws, Permits, Inspections, and Warranties 11.4 OSHA 29 CFR Part 1904: Recording and Reporting Occupational Injuries and Illnesses

9.4 Uniform Mechanical Code vs. International Mechanical Code: Adoption, Differences, and Locating Code Answers

Key Takeaways Explain This Topic AI

The Texas ACR exam reference list names both the Uniform Mechanical Code (IAPMO) and the International Mechanical Code plus International Fuel Gas Code (ICC): 2021 editions now, 2024 editions effective September 1, 2026.

16 TAC 75.110 (Applicable Codes) has adopted the 2021 IRC, IMC, IFGC and UMC since September 1, 2024, and TDLR's update to the 2024 editions carries the same September 1, 2026 date as the exam reference change.

Under 16 TAC 75.100(e) the standard of practice inside a municipality is the code that municipality adopted by ordinance; where no code is adopted, commercial ACR work may follow either the UMC or the IMC with the IFGC and IECC.

The UMC keeps fuel gas piping inside the mechanical book at Chapter 13, while the ICC family moves fuel gas to the separate IFGC and uses IMC Chapter 13 for fuel oil piping and storage.

UMC and IMC track subject-for-subject through Chapters 3 to 12 (general regulations, ventilation, exhaust, ducts, combustion air, chimneys and vents, specific appliances, boilers, refrigeration, hydronics) and diverge after that.

Last updated: August 2026

Two Model Codes on One Reference Shelf

The Texas Department of Licensing and Regulation (TDLR) air conditioning and refrigeration (ACR) contractor exams are open book , and the approved reference list is unusual: it names both competing model mechanical codes. You may bring the Uniform Mechanical Code (UMC) , published by the International Association of Plumbing and Mechanical Officials (IAPMO) , together with the International Mechanical Code (IMC) and International Fuel Gas Code (IFGC) , published by the International Code Council (ICC) . The list currently specifies the 2021 editions , and the 2024 editions become the graded references on September 1, 2026 .

That edition date is not trivia. Section numbers, table values and referenced standards move between code cycles, and PSI writes and grades items against the edition on the published list. Carrying a 2018 UMC to a 2021-edition exam, or a 2021 IMC after the 2024 changeover, turns your open book into a liability — you will find a plausible number under a familiar section heading and it will be the wrong one.

The two books exist because American mechanical codes grew from two lineages. IAPMO's Uniform family (Uniform Plumbing Code, Uniform Mechanical Code) developed out of the western regional model-code tradition and is maintained through an ANSI-accredited consensus process. The ICC's International family (IBC, IRC, IMC, IFGC, IECC) was consolidated in the 1990s from the three former regional model-code organizations and is maintained through a governmental consensus process. Most of the United States, and most of Texas, is on the ICC family — but not all of it, which is exactly why TDLR still tests both.

How Texas Actually Adopts a Mechanical Code

Texas does not write its own mechanical code. Three layers stack on top of each other, and exam questions get written at every layer.

Statute. Texas Occupations Code Section 1302.101(a) directs the Texas Commission of Licensing and Regulation to adopt rules for the practice of air conditioning and refrigeration contracting that are at least as strict as the standards provided by the Uniform Mechanical Code and the International Mechanical Code. The statute itself names both books, which is the legal root of the dual reference list.

TDLR rule. 16 Texas Administrative Code Section 75.110, Applicable Codes , is where the editions live. Effective September 1, 2024, the adopted codes are the 2021 International Residential Code, 2021 International Mechanical Code, 2021 International Fuel Gas Code and 2021 Uniform Mechanical Code ; work permitted or started before that date could be completed under the 2018 editions. TDLR's 2026 rulemaking updates Section 75.110 from the 2021 to the 2024 editions effective September 1, 2026 — the same date the PSI reference list flips.

Where the work is. 16 TAC Section 75.100(e) sets the standard of practice for the licensee. Inside a municipality, the standard is the code the municipality adopted by ordinance . Where no code has been adopted, one- and two-family dwellings and townhouses follow the applicable edition of the IRC with the IFGC and IECC, and commercial work and larger multifamily work may follow either the UMC or the IMC, IFGC and IECC — the contractor chooses.

Municipal codes ride on the Texas Local Government Code. Section 214.212 adopts the International Residential Code as the municipal residential building code statewide, and Section 214.216 does the same for the International Building Code on commercial construction, while expressly allowing a municipality to add, modify or delete requirements by local amendment adopted by ordinance after a public hearing.

The practical Texas picture: Dallas enforces a mechanical code based on the 2021 IMC, while Austin enforces a mechanical code based on the 2024 UMC (Ordinance 20250410-044, effective July 10, 2025) — Austin remains one of only a handful of Texas cities still on the Uniform codes, and it is currently a code cycle ahead of the 2021 edition the exam is graded against. Two jobs 200 miles apart can be governed by two different books plus two different sets of amendments.

The exam consequence: the test grades the model code on the list; the jobsite obeys the locally adopted and amended edition. Never answer an exam item from your city's amendment, and never quote the model code to an inspector as if it overrode the local ordinance.