Study guide
4.2 AIM Act Phasedown, Next-Gen Low-GWP Refrigerants (R-454B, R-32), and A2L Safety Rules
Texas Air Conditioning and Refrigeration Contractor License Exam Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
About the Texas ACR Contractor Exam Open-Book Strategy and the Approved Reference Library
2 Chapter 1: Texas Licensing Laws & TDLR Regulations
1.1 TDLR Licensing Framework, Class A vs Class B Scope, and Technician Registration 1.2 Insurance, Financial Responsibility, Display of License, and Advertising Rules 1.3 TDLR Enforcement, Violations, Administrative Penalties, and Continuing Education
3 Chapter 2: Thermodynamics & Core HVAC Principles
2.1 Heat Transfer Principles: Conduction, Convection, Radiation, and Sensible vs Latent Heat 2.2 Temperature, Pressure, Enthalpy, and the Pressure-Temperature Relationship 2.3 System Airflow Fundamentals, CFM Calculations, and Total External Static Pressure
4 Chapter 3: Load Calculations & System Sizing (Manual J, S, D)
3.1 ACCA Manual J Load Calculations: Heat Gain, Heat Loss, and Building Envelope Factors 3.2 ACCA Manual S Equipment Selection and Manual D Duct Design Principles 3.3 Texas Climate Design Conditions, Solar Gain, and Infiltration Adjustments
5 Chapter 4: Refrigerants, EPA Section 608 & Low-GWP A2L Transition
4.1 Refrigerant Classifications (CFC, HCFC, HFC, HFO) and EPA Section 608 Rules 4.2 AIM Act Phasedown, Next-Gen Low-GWP Refrigerants (R-454B, R-32), and A2L Safety Rules 4.3 Refrigerant Recovery, Recycling, Reclamation, Leak Repair Thresholds, and Evacuation
6 Chapter 5: Refrigeration Cycle & Core System Components
5.1 The Vapor-Compression Refrigeration Cycle and System Component States 5.2 Compressors: Types (Scroll, Reciprocating, Rotary), Maintenance, and Failure Modes 5.3 Condensers, Evaporators, and Expansion Devices (TXV, EEV, Fixed Orifice) 5.4 Service Valves, Filter-Driers, Sight Glasses, and Solenoid & Check Valves
7 Chapter 6: Air Distribution, Ductwork & Indoor Air Quality
6.1 Duct Layouts, Materials, Insulation, Duct Sealing, and Friction Loss 6.2 Air Balancing, Blower Performance Curves, and Air Distribution Fittings 6.3 Indoor Air Quality (IAQ): Ventilation, Filtration, Humidity Control, and ASHRAE 62.2 6.4 Mechanical Ventilation Rates, Air Equipment, and Refrigeration Machinery Rooms
8 Chapter 7: Heating Systems, Gas Controls & Venting
7.1 Gas-Fired Heating: Natural Gas, LP, Burners, Heat Exchangers, and Gas Piping 7.2 Gas Furnace Venting Categories, Draft Hoods, and Combustion Air Requirements 7.3 Electric Resistance Heating and Heat Pump Operation in Heating & Defrost Modes 7.4 Clothes Dryer Exhaust and Product-Conveying Duct Systems 7.5 Combustion Testing and Analysis: CO, Oxygen, Stack Temperature, Draft, and Efficiency
9 Chapter 8: Electrical Systems, Controls & Troubleshooting
8.1 HVAC Electrical Fundamentals: Voltage, Current, Resistance, and Transformer Sizing 8.2 Electric Motors: PSC, ECM, Capacitor Sizing, Relays, Contactors, and Starters 8.3 Schematics Reading, Control Circuits (24V), Thermostats, and Diagnostic Sequence 8.4 Pressure and Safety Controls: High/Low Pressure, Oil Safety, Freeze Protection, and Head Pressure Control
10 Chapter 9: Mechanical Codes & Texas Local Standards (IMC, IFGC & UMC)
9.1 International Mechanical Code (IMC): Equipment Clearances, Access, and Support 9.2 International Fuel Gas Code (IFGC): Pipe Sizing, Materials, Purging, and Testing 9.3 Condensate Drain Piping, Trap Sizing, Secondary Drain Protection, and Auxiliary Pans 9.4 Uniform Mechanical Code vs. International Mechanical Code: Adoption, Differences, and Locating Code Answers 9.5 Refrigerant Line Sizing, Piping Materials, Brazing, Oil Return, and Pipe Support
11 Chapter 10: Commercial Refrigeration & Process Cooling Systems
10.1 Commercial Refrigeration Systems: Walk-in Freezers, Coolers, and Multi-Compressor Racks 10.2 Defrost Systems: Electric, Hot Gas, Off-Cycle, and Evaporator Pressure Regulators (EPR) 10.3 Hydronic Chilled Water Systems, Boilers, and Process Cooling Fundamentals
12 Chapter 11: Jobsite Safety, OSHA Compliance & Business Practice
11.1 OSHA Safety Standards: Fall Protection, Personal Protective Equipment (PPE), and Ladder Safety 11.2 Lockout/Tagout (LOTO), Electrical Safety, High-Pressure Gas Cylinder Handling 11.3 Contractor Business Operations: Contracts, Lien Laws, Permits, Inspections, and Warranties 11.4 OSHA 29 CFR Part 1904: Recording and Reporting Occupational Injuries and Illnesses
4.2 AIM Act Phasedown, Next-Gen Low-GWP Refrigerants (R-454B, R-32), and A2L Safety Rules
Key Takeaways Explain This Topic AI
The AIM Act mandates an 85% nationwide phasedown of HFC production and consumption by 2036, accelerating adoption of low-GWP refrigerants.
Next-generation A2L refrigerants such as R-454B (GWP ~466) and R-32 (GWP ~675) replace R-410A (GWP 2,088) in residential and light commercial HVAC applications.
ASHRAE Standard 15 and UL 60335-2-40 govern safety compliance, requiring mechanical ventilation, sensor detection, and charge limits for A2L equipment.
A2L recovery cylinders and charging equipment utilize left-hand reverse thread connections (CGA 166) and spark-proof electrical components to mitigate ignition risks.
AHRI standardizes all new refrigerant cylinders to a light green-grey color (RAL 7044) with a distinct red band indicating flammable refrigerant contents.
Last updated: August 2026
4.2 AIM Act Phasedown, Next-Gen Low-GWP Refrigerants, and A2L Safety Rules
The HVAC industry is undergoing its most significant technological shift in thirty years. Driven by federal legislation and updated safety standards, high-GWP hydrofluorocarbons (such as R-410A) are being replaced by next-generation A2L mildly flammable refrigerants. Texas licensed HVAC contractors must understand the statutory timelines governing this transition, the thermodynamic properties of new A2L blends, and the mandatory field handling and equipment safety rules required for safe compliance.
AIM Act Statutory Framework & Allocation Phasedown
Enacted by the United States Congress in December 2020, the American Innovation and Manufacturing (AIM) Act grants the Environmental Protection Agency (EPA) explicit federal authority to phase down the production and consumption of high-GWP hydrofluorocarbons (HFCs) by 85% over a 15-year statutory schedule .
Rather than executing an immediate outright ban on existing HFC equipment, the AIM Act establishes a cap-and-trade allowance allocation system. The EPA sets nationwide production and import baselines and systematically reduces available allowances according to fixed benchmark percentages: AIM ACT HFC ALLOCATION PHASEDOWN TIMELINE
- Baseline (100%) [2020-2023] ======================================== 100%
- Step 1 (90%) [2022-2023] =================================== 90%
- Step 2 (60%) [2024-2028] ======================= 60%
- Step 3 (30%) [2029-2033] =========== 30%
- Step 4 (20%) [2034-2035] ======= 20%
- Step 5 (15%) [2036+] ====== 15% (85% Total Reduction)
- Phasedown Period Statutory Production & Import Cap Cumulative Reduction from Baseline
- 2020 – 2023 Baseline 100% Baseline Allocation 0% Reduction
- 2022 – 2023 90% Baseline Allocation 10% Reduction
- 2024 – 2028 60% Baseline Allocation 40% Reduction
- 2029 – 2033 30% Baseline Allocation 70% Reduction
- 2034 – 2035 20% Baseline Allocation 80% Reduction
- 2036 and beyond 15% Baseline Allocation 85% Total Phasedown
- EPA Technology Transitions Rule
Complementing allowance phasedowns, the EPA issued Technology Transitions rules under the AIM Act setting maximum GWP limits for refrigerants used in new equipment installations:
Residential & Light Commercial AC / Heat Pumps: Effective January 1, 2025 , refrigerants with a GWP of 700 or greater may no longer be used in the manufacture or import of residential and light commercial comfort cooling equipment. The installation cutoff is separate and later: field-assembled split systems could still be installed from components manufactured before January 1, 2025 until January 1, 2026 , and self-contained products carry their own sell-through window. Confusing the manufacture date with the installation date is the classic error on this transition. This GWP cap eliminates R-410A (GWP = 2,088) from new equipment manufacturing and new system installations.
Next-Generation Low-GWP A2L Refrigerants
To satisfy the 700 GWP regulatory limit while maintaining high energy efficiency, equipment manufacturers have adopted ASHRAE Class A2L (lower toxicity, mildly flammable) refrigerants as primary replacements for R-410A.
- Primary A2L Compounds
- 1. R-454B (Trade Name: Opteon XL20 / Puron Advance)
Composition: A zeotropic blend consisting of 68.9% R-32 (HFC) and 31.1% R-1234yf (HFO).
GWP Rating: Approximately 466 (an approximate 78% reduction in GWP compared to R-410A).
Operating Characteristics: Operates at system pressures and temperatures nearly identical to R-410A, making heat exchanger design and compressor sizing highly comparable. R-454B has been selected by major manufacturers (including Carrier, Trane, York, and Lennox) as their primary residential split-system refrigerant.
Temperature Glide: Exhibits a small temperature glide ( < 1.5 ∘ F < 1.5^\circ\text{F} < 1. 5 ∘ F ), requiring liquid charging when adding refrigerant to systems.
2. R-32 (Difluoromethane)
Composition: A single-component HFC compound ( C H 2 F 2 CH_2F_2 C H 2 F 2 ).
GWP Rating: 675 (satisfies the < 700 < 700 < 700 GWP threshold).
Operating Characteristics: Exhibits higher operating pressures (roughly 5% higher than R-410A) and significantly higher compressor discharge temperatures. Systems utilizing R-32 require active liquid injection or advanced compressor thermal management to prevent oil breakdown during high ambient conditions. Selected by Daikin, Goodman, and Amana.
Temperature Glide: Zero glide (pure single-component refrigerant), allowing vapor or liquid charging.
3. R-452B (Opteon XL55)
Composition: A zeotropic blend of R-32 (67%), R-125 (7%), and R-1234yf (26%).
GWP Rating: 698 .
Operating Characteristics: Provides a close thermodynamic match to R-410A with lower discharge temperatures than pure R-32, primarily utilized in heavy commercial scroll chillers and commercial heat pumps.
- Refrigerant Property Legacy R-410A Next-Gen R-454B Next-Gen R-32 Legacy R-22
- ASHRAE Safety Class A1 (Non-Flammable) A2L (Mildly Flammable) A2L (Mildly Flammable) A1 (Non-Flammable)
- GWP Value (100-yr) 2,088 466 675 1,810
- Ozone Depletion (ODP) 0.0 0.0 0.0 0.055
- Composition 50% R-32 / 50% R-125 68.9% R-32 / 31.1% R-1234yf 100% R-32 (Pure) 100% HCFC-22
- Burning Velocity N/A 5.2 cm/s 5.2\text{ cm/s} 5.2 cm/s 6.7 cm/s 6.7\text{ cm/s} 6.7 cm/s N/A
LFL ( kg/m 3 \text{kg/m}^3 kg/m 3 ) N/A 0.30 kg/m 3 0.30\text{ kg/m}^3 0.30 kg/m 3 0.307 kg/m 3 0.307\text{ kg/m}^3 0.307 kg/m 3 N/A
- Primary Application Phaseout (Pre-2025) Residential AC / Heat Pump Residential AC / Heat Pump Phased Out
- Safety Standards & Equipment Design (ASHRAE 15 & UL 60335-2-40)
The safe field deployment of A2L refrigerants is governed by two complementary standards:
ASHRAE Standard 15: Safety Standard for Refrigeration Systems (building code application rules).
UL 60335-2-40: Safety of Household and Similar Electrical Appliances (equipment manufacturing design rules).
- Critical Safety Compliance Mechanisms
- 1. Allowable Charge Limits & Room Volume Calculations
Because A2L refrigerants possess mild flammability, building standards enforce strict maximum allowable charge limits based on occupied room volume. The formula calculates the maximum unmitigated refrigerant charge ( M m a x M_{max} M ma x ) allowed in a space before safety controls become mandatory: M m a x = 0.25 × LFL × V M_{max} = 0.25 \times \text{LFL} \times V M ma x = 0.25 × LFL × V
Where:
LFL = \text{LFL} = LFL = Lower Flammability Limit of the refrigerant ( kg/m 3 \text{kg/m}^3 kg/m 3 or lb/1,000 ft 3 \text{lb/1,000 ft}^3 lb/1,000 ft 3 ).
V = V = V = Volume of the enclosed occupied space ( m 3 \text{m}^3 m 3 or ft 3 \text{ft}^3 ft 3 ).
If the total system refrigerant charge exceeds M m a x M_{max} M ma x for the smallest connected space (such as a small bedroom or office connected via ductwork), the installation must incorporate active mitigation controls .
2. Refrigerant Detection Systems (RDS) & Mitigation
Modern A2L HVAC units feature factory-integrated Refrigerant Detection Systems (RDS) embedded in indoor evaporator coil cabinets and return air plenums.
Operating Logic: If the RDS sensor detects an A2L leak concentration reaching 25% of the refrigerant's LFL , the RDS control board automatically initiates active mitigation:
Immediately energizes the indoor evaporator blower fan at full speed to rapidly circulate and dilute leaking gas below flammable concentrations.
De-energizes the 24VAC control circuit to the outdoor unit, shutting down the compressor and closing liquid-line solenoid valves to isolate the refrigerant charge.
Activates visual or audible trouble alarms.
A2L Handling Requirements & Tooling Standards
Servicing A2L systems requires specialized technician procedures and safety-rated service tools. Standard A1 tools cannot automatically be assumed safe for A2L operations.
1. Reverse-Thread Cylinder Valve Connections (CGA 166)
To prevent technicians from accidentally connecting standard right-hand threaded charging hoses or recovery machines to flammable gas containers, A2L recovery cylinders and refrigerant tanks feature left-hand reverse threads (CGA 166 / CGA 164 connections) .
Field Identification: Left-hand threaded fittings feature a distinct outer notch machined into the hexagonal connector nut. STANDARD RIGHT-HAND THREAD (A1) REVERSE LEFT-HAND THREAD (A2L)
- Turn Clockwise to Tighten Turn Counter-Clockwise to Tighten
- [ Standard Smooth Hex Nut ] [ Hex Nut with Outer Machined Groove ]
- 2. Spark-Proof & Non-Sparking Service Equipment
Technicians servicing A2L systems must utilize certified non-sparking / intrinsically safe service tools tested under ISO 5149 or IEC 60079-15 standards:
Recovery Machines: Must feature sealed switches, brushless DC motors, and enclosed relays to eliminate internal electrical arcing.
Vacuum Pumps: Must be equipped with non-sparking switches and explosion-proof motor enclosures. Vacuum pumps used for A2L service must exhaust vapors to a well-ventilated outdoor location.
Electronic Leak Detectors: Must be certified intrinsically safe for Class I, Division 2 environments, utilizing heated diode or infrared sensors validated for A2L detection.
AHRI Cylinder Color Standardization (Guideline N)
In historical practice, the Air-Conditioning, Heating, and Refrigeration Institute (AHRI) assigned unique container paint colors to each refrigerant (e.g., light green for R-22, rose pink for R-410A, sky blue for R-134a). However, with the rapid influx of dozens of new refrigerant blends, color confusion posed severe safety hazards.
Under revised AHRI Guideline N :
Uniform Base Color: All new refrigerant containers must be painted a uniform neutral base color: Light Green-Grey (RAL 7044) .
Flammable Gas Hazard Band: Containers holding Class A2L, A2, or A3 flammable refrigerants must feature a prominent, permanent Red Band painted around the top shoulder or container body, accompanied by a United States Department of Transportation (DOT) Red Flammable Gas Diamond Hazard Label.