Study guide
4.3 Refrigerant Recovery, Recycling, Reclamation, Leak Repair Thresholds, and Evacuation
Texas Air Conditioning and Refrigeration Contractor License Exam Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
About the Texas ACR Contractor Exam Open-Book Strategy and the Approved Reference Library
2 Chapter 1: Texas Licensing Laws & TDLR Regulations
1.1 TDLR Licensing Framework, Class A vs Class B Scope, and Technician Registration 1.2 Insurance, Financial Responsibility, Display of License, and Advertising Rules 1.3 TDLR Enforcement, Violations, Administrative Penalties, and Continuing Education
3 Chapter 2: Thermodynamics & Core HVAC Principles
2.1 Heat Transfer Principles: Conduction, Convection, Radiation, and Sensible vs Latent Heat 2.2 Temperature, Pressure, Enthalpy, and the Pressure-Temperature Relationship 2.3 System Airflow Fundamentals, CFM Calculations, and Total External Static Pressure
4 Chapter 3: Load Calculations & System Sizing (Manual J, S, D)
3.1 ACCA Manual J Load Calculations: Heat Gain, Heat Loss, and Building Envelope Factors 3.2 ACCA Manual S Equipment Selection and Manual D Duct Design Principles 3.3 Texas Climate Design Conditions, Solar Gain, and Infiltration Adjustments
5 Chapter 4: Refrigerants, EPA Section 608 & Low-GWP A2L Transition
4.1 Refrigerant Classifications (CFC, HCFC, HFC, HFO) and EPA Section 608 Rules 4.2 AIM Act Phasedown, Next-Gen Low-GWP Refrigerants (R-454B, R-32), and A2L Safety Rules 4.3 Refrigerant Recovery, Recycling, Reclamation, Leak Repair Thresholds, and Evacuation
6 Chapter 5: Refrigeration Cycle & Core System Components
5.1 The Vapor-Compression Refrigeration Cycle and System Component States 5.2 Compressors: Types (Scroll, Reciprocating, Rotary), Maintenance, and Failure Modes 5.3 Condensers, Evaporators, and Expansion Devices (TXV, EEV, Fixed Orifice) 5.4 Service Valves, Filter-Driers, Sight Glasses, and Solenoid & Check Valves
7 Chapter 6: Air Distribution, Ductwork & Indoor Air Quality
6.1 Duct Layouts, Materials, Insulation, Duct Sealing, and Friction Loss 6.2 Air Balancing, Blower Performance Curves, and Air Distribution Fittings 6.3 Indoor Air Quality (IAQ): Ventilation, Filtration, Humidity Control, and ASHRAE 62.2 6.4 Mechanical Ventilation Rates, Air Equipment, and Refrigeration Machinery Rooms
8 Chapter 7: Heating Systems, Gas Controls & Venting
7.1 Gas-Fired Heating: Natural Gas, LP, Burners, Heat Exchangers, and Gas Piping 7.2 Gas Furnace Venting Categories, Draft Hoods, and Combustion Air Requirements 7.3 Electric Resistance Heating and Heat Pump Operation in Heating & Defrost Modes 7.4 Clothes Dryer Exhaust and Product-Conveying Duct Systems 7.5 Combustion Testing and Analysis: CO, Oxygen, Stack Temperature, Draft, and Efficiency
9 Chapter 8: Electrical Systems, Controls & Troubleshooting
8.1 HVAC Electrical Fundamentals: Voltage, Current, Resistance, and Transformer Sizing 8.2 Electric Motors: PSC, ECM, Capacitor Sizing, Relays, Contactors, and Starters 8.3 Schematics Reading, Control Circuits (24V), Thermostats, and Diagnostic Sequence 8.4 Pressure and Safety Controls: High/Low Pressure, Oil Safety, Freeze Protection, and Head Pressure Control
10 Chapter 9: Mechanical Codes & Texas Local Standards (IMC, IFGC & UMC)
9.1 International Mechanical Code (IMC): Equipment Clearances, Access, and Support 9.2 International Fuel Gas Code (IFGC): Pipe Sizing, Materials, Purging, and Testing 9.3 Condensate Drain Piping, Trap Sizing, Secondary Drain Protection, and Auxiliary Pans 9.4 Uniform Mechanical Code vs. International Mechanical Code: Adoption, Differences, and Locating Code Answers 9.5 Refrigerant Line Sizing, Piping Materials, Brazing, Oil Return, and Pipe Support
11 Chapter 10: Commercial Refrigeration & Process Cooling Systems
10.1 Commercial Refrigeration Systems: Walk-in Freezers, Coolers, and Multi-Compressor Racks 10.2 Defrost Systems: Electric, Hot Gas, Off-Cycle, and Evaporator Pressure Regulators (EPR) 10.3 Hydronic Chilled Water Systems, Boilers, and Process Cooling Fundamentals
12 Chapter 11: Jobsite Safety, OSHA Compliance & Business Practice
11.1 OSHA Safety Standards: Fall Protection, Personal Protective Equipment (PPE), and Ladder Safety 11.2 Lockout/Tagout (LOTO), Electrical Safety, High-Pressure Gas Cylinder Handling 11.3 Contractor Business Operations: Contracts, Lien Laws, Permits, Inspections, and Warranties 11.4 OSHA 29 CFR Part 1904: Recording and Reporting Occupational Injuries and Illnesses
4.3 Refrigerant Recovery, Recycling, Reclamation, Leak Repair Thresholds, and Evacuation
Key Takeaways Explain This Topic AI
Refrigerant recovery extracts chemical without processing, recycling filters it for reuse in the same system owner's equipment, and reclamation restores chemical purity to AHRI 700 standards.
System evacuation requires achieving a deep vacuum of 500 microns (0.5 Torr) to remove non-condensable gases and vaporize internal moisture.
EPA Section 608 mandates annual leak repair trigger thresholds of 30% for industrial process refrigeration, 20% for commercial refrigeration, and 10% for comfort cooling in systems containing 50+ lbs charge.
Technicians must complete mandatory leak repairs within 30 calendar days (or 120 days for industrial process shutdowns) followed by initial and verification testing within 10 days.
EPA rules require detailed service, recovery, and leak inspection recordkeeping to be maintained for 3 years for equipment containing 5 or more pounds of refrigerant.
Last updated: October 2026
Proper refrigerant management is both an environmental necessity and a strict legal requirement under federal and state law. Technicians and licensed contractors in Texas must possess precise working knowledge of refrigerant containment procedures, deep vacuum evacuation protocols, mandatory EPA Section 608 leak rate repair thresholds, and statutory recordkeeping mandates.
The Three R's: Recovery, Recycling, and Reclamation
Federal regulations under EPA Section 608 establish precise legal definitions for handling recovered refrigerants. Confusing these terms on the licensing exam or in field practice carries severe regulatory penalties.
1. Recovery
Definition: Removing refrigerant in any condition from an appliance and storing it in an external approved container without necessarily testing or processing it.
Key Rule: Recovery is mandatory prior to performing any system service, repair, or disposal that involves opening the refrigerant circuit. Refrigerant cannot be legally vented during recovery operations.
2. Recycling
Definition: Cleaning recovered refrigerant for reuse by reducing moisture, acidity, and particulate contamination through oil separation and single or multiple passes through replaceable moisture-core filter-driers.
Ownership & Usage Restrictions: Recycled refrigerant may ONLY be reinstalled into the original equipment from which it was recovered, or into another appliance owned by the exact same equipment owner . Recycled refrigerant cannot be sold or transferred to a different equipment owner.
3. Reclamation
Definition: Reprocessing recovered refrigerant to new product specifications, requiring chemical analysis (such as gas chromatography) to verify that it meets AHRI Standard 700 purity standards.
Resale Rule: Reclaimed refrigerant is the ONLY processed refrigerant that can legally be sold or transferred to a different equipment owner. Reclamation must be performed by an EPA-certified refrigerant reclaimer.
Process Technical Definition Processing Level Permitted Destination / Usage
Recovery Extracting refrigerant from a system into an external tank None (raw state) Recovery cylinder for recycling, reclamation, or disposal
Recycling Cleaning via oil separator & filter-driers on-site Basic filtering Same system or another system owned by the same owner
Reclamation Chemical re-refining to AHRI 700 purity specs Laboratory verification Open market resale to any third-party customer
- Recovery Methods & Deep Vacuum Evacuation Protocols
- Recovery Techniques
Active (Self-Contained) Recovery: Uses an independent, motor-driven recovery machine to extract refrigerant from the appliance. Active recovery is required for all medium and high-pressure systems.
Vapor Recovery: Standard method where vapor is drawn from system access valves, compressed by the recovery machine, and condensed into the recovery cylinder.
Push-Pull Liquid Recovery: Used for bulk liquid removal on systems containing 10 pounds or more of refrigerant. The recovery machine pulls vapor from the recovery cylinder, pressurizes the system's liquid receiver or condenser, and pushes liquid refrigerant directly out of the system into the cylinder liquid port.
Passive (System-Dependent) Recovery: Relies on the appliance's internal compressor or system pressure to push refrigerant into a non-pressurized recovery container. Passive recovery is permitted only on Type I small appliances (containing 5 lbs or less charge).
System Evacuation & Dehydration (500-Micron Standard)
When a refrigeration circuit is opened for repair, atmospheric air and moisture enter the tubing. Moisture reacts with synthetic polyolester (POE) or mineral oils to form corrosive hydrofluoric and hydrochloric acids, while non-condensable gases elevate head pressures and cause compressor overheating. ATMOSPHERIC PRESSURE CONVERSION METRICS
- Standard Atmosphere = 14.7 psia = 0 psig = 29.92 in. Hg
- Deep Vacuum Target = 500 Microns = 0.5 mm Hg = 0.5 Torr
- Evacuation Target vs. the EPA Recovery Requirement
Distinguish two different numbers. 500 microns is the industry standard evacuation target before charging a new or opened system, measured with an electronic micron gauge — it is best practice and a manufacturer requirement, not an EPA number. Separately, 40 CFR 82.156 sets the recovery evacuation levels a technician must reach before opening an appliance, which vary by appliance type and charge size (for example 90% or 80% recovery, or 4 in. Hg vacuum, for small appliances; 0, 10 or 15 in. Hg vacuum for high- and medium-pressure appliances depending on pressure class and charge; and 25 mm Hg absolute for low-pressure chillers). Systems are evacuated to a deep vacuum of 500 microns (0.5 mm Hg / 0.5 Torr absolute) for service quality;
Tooling Protocol: To achieve 500 microns efficiently, manifold gauge valve cores must be removed using vacuum-rated valve core removal tools, and large-diameter ( 3 / 8 inch 3/8\text{ inch} 3/8 inch or 1 / 2 inch 1/2\text{ inch} 1/2 inch ) vacuum hoses should connect directly from the system to the vacuum pump.
Standing Vacuum Leak Test (Isolation Test)
Once 500 microns is reached, the vacuum pump is isolated from the system using inline core removal tool ball valves.
System Integrity Pass: The micron gauge reading must remain below 1,000 microns for a minimum of 10 to 15 minutes .
Physical Leak Diagnosis: If the micron level rises rapidly and continuously up to atmospheric pressure ( 760 , 000 microns 760,000\text{ microns} 760 , 000 microns ), a physical leak exists in the piping.
Moisture / Outgassing Diagnosis: If the micron level rises steadily but levels off and stabilizes between 1,500 and 2,500 microns, liquid moisture or residual refrigerant dissolved in compressor oil is still outgassing inside the system.
EPA Section 608 Mandatory Leak Repair Rules
Two overlapping federal rules now set leak-repair duties, and the applicable charge-size threshold depends on which refrigerant the appliance holds :
Section 608 (ozone-depleting refrigerants): appliances containing 50 pounds or more of a regulated ODS refrigerant.
AIM Act Emissions Reduction and Reclamation (ER&R) rule, 40 CFR Part 84 subpart (h), in force since January 1, 2026: the same trigger rates, repair windows, and verification tests now also apply to appliances containing 15 pounds or more of an HFC or substitute with a GWP greater than 53 — which captures most modern R-410A, R-454B, and R-32 equipment.
Exam and Field Trap: "Under 50 pounds means no leak-repair obligation" is now wrong for HFC systems. A 20-pound R-410A rack falls under the ER&R rule even though it is far below the old Section 608 threshold.
Annualized Leak Rate Trigger Thresholds
If an appliance above the applicable threshold exceeds its annual leak rate during any 12-month period, the leak must be repaired within mandated timeframes .
Appliance Category Application Description Annualized Leak Rate Trigger
Industrial Process Refrigeration (IPR) Complex custom refrigeration systems used in chemical manufacturing, food processing, cold storage, and ice rinks 30% Annual Leak Rate
Commercial Refrigeration Supermarket rack systems, walk-in freezers, refrigerated display cases, and refrigerated transport 20% Annual Leak Rate
Comfort Cooling Residential central AC, commercial office building chillers, and rooftop split-system HVAC units 10% Annual Leak Rate
Leak Rate Calculation Formula
Technicians calculate the annualized leak rate upon adding refrigerant using the EPA standard formula: Leak Rate (percent) = ( Lbs of Refrigerant Added Total System Full Charge Lbs ) × ( 365 Days Days Since Last Addition ) × 100 \text{Leak Rate (percent)} = \left( \frac{\text{Lbs of Refrigerant Added}}{\text{Total System Full Charge Lbs}} \right) \times \left( \frac{365 \text{ Days}}{\text{Days Since Last Addition}} \right) \times 100 Leak Rate (percent) = ( Total System Full Charge Lbs Lbs of Refrigerant Added ) × ( Days Since Last Addition 365 Days ) × 100
- Mandatory Leak Repair Timelines & Verification Tests
- 1. 30-Day Standard Repair Window
Once the leak rate calculation indicates that the statutory threshold (10%, 20%, or 30%) has been exceeded, the owner/operator has 30 calendar days to successfully repair the leaks so that the system operates below the threshold.
2. 120-Day Industrial Process Exception
If an Industrial Process Refrigeration (IPR) system requires a complex industrial facility shutdown or custom component fabrication, the owner is granted 120 calendar days to complete repairs, provided an official initial repair plan is developed within the first 30 days.
3. Mandatory Verification Testing
Repairs on 50+ lb systems require two separate verification tests:
Initial Verification Test: Conducted immediately after leak repair completion but before recharging refrigerant (e.g., high-pressure nitrogen standing test).
Follow-Up Verification Test: Conducted within 10 calendar days after the initial verification test, while the system is operating at normal operating temperatures and pressures.
4. Retrofit or Retirement Plan
If a leak repair attempt fails verification testing or cannot be completed within 30 days, the equipment owner must develop an official Retrofit or Retirement Plan within 30 days and fully execute the plan within 1 year (365 days) .
EPA Recordkeeping Requirements
Licensed Texas HVAC contractors and equipment owners must maintain comprehensive records of refrigerant handling to demonstrate compliance during EPA audits.
1. Appliances Containing 5 to 50 Pounds of Refrigerant
Servicing contractors must provide equipment owners with invoices detailing:
Date of service and location of equipment.
Name of technician and Section 608 certification number.
Exact quantity (in pounds) and type of refrigerant added or recovered.
Purpose of service and cause of leak (if applicable).
Records must be retained by both contractor and owner for 3 years .
2. Appliances Containing More Than 50 Pounds of Refrigerant
Owners/operators of 50+ lb systems must maintain full operational logs for 3 years , including:
Full charge size calculation methods.
Dates and quantities of all refrigerant additions and recoveries.
Annualized leak rate calculation records.
Initial and follow-up verification test documentation.