Study guide

5.3 Condensers, Evaporators, and Expansion Devices (TXV, EEV, Fixed Orifice)

Texas Air Conditioning and Refrigeration Contractor License Exam Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

About the Texas ACR Contractor Exam Open-Book Strategy and the Approved Reference Library

2 Chapter 1: Texas Licensing Laws & TDLR Regulations

1.1 TDLR Licensing Framework, Class A vs Class B Scope, and Technician Registration 1.2 Insurance, Financial Responsibility, Display of License, and Advertising Rules 1.3 TDLR Enforcement, Violations, Administrative Penalties, and Continuing Education

3 Chapter 2: Thermodynamics & Core HVAC Principles

2.1 Heat Transfer Principles: Conduction, Convection, Radiation, and Sensible vs Latent Heat 2.2 Temperature, Pressure, Enthalpy, and the Pressure-Temperature Relationship 2.3 System Airflow Fundamentals, CFM Calculations, and Total External Static Pressure

4 Chapter 3: Load Calculations & System Sizing (Manual J, S, D)

3.1 ACCA Manual J Load Calculations: Heat Gain, Heat Loss, and Building Envelope Factors 3.2 ACCA Manual S Equipment Selection and Manual D Duct Design Principles 3.3 Texas Climate Design Conditions, Solar Gain, and Infiltration Adjustments

5 Chapter 4: Refrigerants, EPA Section 608 & Low-GWP A2L Transition

4.1 Refrigerant Classifications (CFC, HCFC, HFC, HFO) and EPA Section 608 Rules 4.2 AIM Act Phasedown, Next-Gen Low-GWP Refrigerants (R-454B, R-32), and A2L Safety Rules 4.3 Refrigerant Recovery, Recycling, Reclamation, Leak Repair Thresholds, and Evacuation

6 Chapter 5: Refrigeration Cycle & Core System Components

5.1 The Vapor-Compression Refrigeration Cycle and System Component States 5.2 Compressors: Types (Scroll, Reciprocating, Rotary), Maintenance, and Failure Modes 5.3 Condensers, Evaporators, and Expansion Devices (TXV, EEV, Fixed Orifice) 5.4 Service Valves, Filter-Driers, Sight Glasses, and Solenoid & Check Valves

7 Chapter 6: Air Distribution, Ductwork & Indoor Air Quality

6.1 Duct Layouts, Materials, Insulation, Duct Sealing, and Friction Loss 6.2 Air Balancing, Blower Performance Curves, and Air Distribution Fittings 6.3 Indoor Air Quality (IAQ): Ventilation, Filtration, Humidity Control, and ASHRAE 62.2 6.4 Mechanical Ventilation Rates, Air Equipment, and Refrigeration Machinery Rooms

8 Chapter 7: Heating Systems, Gas Controls & Venting

7.1 Gas-Fired Heating: Natural Gas, LP, Burners, Heat Exchangers, and Gas Piping 7.2 Gas Furnace Venting Categories, Draft Hoods, and Combustion Air Requirements 7.3 Electric Resistance Heating and Heat Pump Operation in Heating & Defrost Modes 7.4 Clothes Dryer Exhaust and Product-Conveying Duct Systems 7.5 Combustion Testing and Analysis: CO, Oxygen, Stack Temperature, Draft, and Efficiency

9 Chapter 8: Electrical Systems, Controls & Troubleshooting

8.1 HVAC Electrical Fundamentals: Voltage, Current, Resistance, and Transformer Sizing 8.2 Electric Motors: PSC, ECM, Capacitor Sizing, Relays, Contactors, and Starters 8.3 Schematics Reading, Control Circuits (24V), Thermostats, and Diagnostic Sequence 8.4 Pressure and Safety Controls: High/Low Pressure, Oil Safety, Freeze Protection, and Head Pressure Control

10 Chapter 9: Mechanical Codes & Texas Local Standards (IMC, IFGC & UMC)

9.1 International Mechanical Code (IMC): Equipment Clearances, Access, and Support 9.2 International Fuel Gas Code (IFGC): Pipe Sizing, Materials, Purging, and Testing 9.3 Condensate Drain Piping, Trap Sizing, Secondary Drain Protection, and Auxiliary Pans 9.4 Uniform Mechanical Code vs. International Mechanical Code: Adoption, Differences, and Locating Code Answers 9.5 Refrigerant Line Sizing, Piping Materials, Brazing, Oil Return, and Pipe Support

11 Chapter 10: Commercial Refrigeration & Process Cooling Systems

10.1 Commercial Refrigeration Systems: Walk-in Freezers, Coolers, and Multi-Compressor Racks 10.2 Defrost Systems: Electric, Hot Gas, Off-Cycle, and Evaporator Pressure Regulators (EPR) 10.3 Hydronic Chilled Water Systems, Boilers, and Process Cooling Fundamentals

12 Chapter 11: Jobsite Safety, OSHA Compliance & Business Practice

11.1 OSHA Safety Standards: Fall Protection, Personal Protective Equipment (PPE), and Ladder Safety 11.2 Lockout/Tagout (LOTO), Electrical Safety, High-Pressure Gas Cylinder Handling 11.3 Contractor Business Operations: Contracts, Lien Laws, Permits, Inspections, and Warranties 11.4 OSHA 29 CFR Part 1904: Recording and Reporting Occupational Injuries and Illnesses

5.3 Condensers, Evaporators, and Expansion Devices (TXV, EEV, Fixed Orifice)

Key Takeaways Explain This Topic AI

Condensers reject Total Heat Rejection (THR), combining evaporator heat absorption with compressor work heat; approach temperature evaluates water-cooled condenser fouling.

Evaporator fin spacing is customized for thermal applications, using coarse spacing (4-8 FPI) in low-temperature refrigeration to manage frost accumulation alongside electric or hot gas defrost.

Fixed orifice metering devices supply constant restriction and must be charged exclusively using the Target Superheat method based on indoor wet-bulb and outdoor dry-bulb temperatures.

Thermostatic Expansion Valves (TXVs) regulate flow via a three-force balance equation (P1 = P2 + P3) to maintain constant superheat, requiring charging by the Subcooling method.

TXVs installed on evaporator coils with high internal pressure drops or refrigerant distributors require an external equalizer line to prevent coil pressure drop from artificially closing the valve.

Last updated: August 2026

Condenser Heat Exchangers: Engineering Principles

The condenser coil rejects thermal energy from the high-pressure refrigerant to an external cooling medium (ambient air or water). The total heat rejected by the condenser is termed Total Heat Rejection (THR) and equals the heat absorbed by the evaporator plus the heat of compression added by the compressor motor: THR = Q evaporator + W compressor \text{THR} = Q_{\text{evaporator}} + W_{\text{compressor}} THR = Q evaporator ​ + W compressor ​

1. Air-Cooled Condensers

Air-cooled condensers pass outdoor air over finned copper or aluminum tubes using propeller or backward-curved centrifugal fans.

Condenser Split: The difference between the condensing saturation temperature ( T c o n d _ s a t T_{cond\_sat} T co n d _ s a t ​ ) and the entering air dry-bulb temperature ( T a m b i e n t T_{ambient} T ambi e n t ​ ). Standard efficiency systems (13-14 SEER) operate with a 20°F to 30°F split, whereas high-efficiency SEER2 systems operate with a 10°F to 15°F split.

Low-Ambient Head Pressure Controls: When outdoor temperatures drop, condensing pressure falls rapidly, starving the metering device. Low-ambient controls maintain head pressure via fan speed controllers (VFDs) , fan cycling pressure switches , or condenser flooding valves (Headmaster valves) that back up liquid refrigerant into the condenser tubes to reduce effective condensing surface area.

2. Water-Cooled Condensers

Water-cooled condensers utilize water as the heat sink, achieving lower condensing temperatures and higher efficiency than air-cooled units.

Configurations: Tube-in-tube (coaxial), Shell-and-coil, and Shell-and-tube.

Approach Temperature: The temperature difference between the leaving liquid refrigerant saturation temperature and the leaving cooling water temperature: Approach Temperature = T leaving liquid sat − T leaving water \text{Approach Temperature} = T_{\text{leaving liquid sat}} - T_{\text{leaving water}} Approach Temperature = T leaving liquid sat ​ − T leaving water ​

Normal approach temperature for shell-and-tube condensers ranges from 2°F to 10°F . High approach temperatures indicate mineral scaling or tube fouling, requiring mechanical rodding or acid flushing.

Water Regulating Valves: Head-pressure-actuated valves mounted on the condenser water inlet modulate water flow to maintain constant condensing head pressure under varying water supply temperatures.

Evaporator Coil Design and Defrost Mechanisms

Evaporators absorb heat into low-pressure boiling refrigerant. Proper airflow across finned tubing is essential to maintain heat transfer coefficient and prevent coil icing.

Fin Spacing and Frost Management

Comfort Air Conditioning: Uses high fin density ( 12 to 18 fins per inch [FPI] ) to maximize surface area and sensible/latent heat removal.

Low-Temperature Refrigeration: Operates at coil saturation temperatures below 32°F. Frost accumulates on fin surfaces; therefore, coarse fin spacing ( 4 to 8 FPI ) is mandated to prevent frost from rapidly choking airflow.

Defrost Systems: Medium and low-temp systems require scheduled defrost cycles: Off-cycle defrost (air defrost for rooms > 35 ∘ F >35^\circ\text{F} > 3 5 ∘ F ), Electric defrost (heating rods embedded in fin pack), or Hot gas defrost (reversing valve or bypass solenoid routes compressor discharge gas into the evaporator).

Distributor Tubes and Feeder Lines

Large evaporator coils utilize a refrigerant distributor downstream of the expansion valve. The distributor evenly splits the expanding liquid/vapor mixture into multiple parallel feeder circuits, ensuring uniform refrigerant mass distribution and equal pressure drop across all coil sections.

Metering Devices and Expansion Fundamentals

The metering device drops high-side subcooled liquid pressure down to low-side evaporating pressure and controls refrigerant mass flow rate into the evaporator coil. +-----------------------------------------------------------------------------------+

  • | METERING DEVICE CLASSIFICATIONS |
  • +------------------------------------+----------------------------------------------+
  • | FIXED ORIFICE | THERMOSTATIC EXPANSION VALVE |
  • | (Piston / Capillary) | (TXV) |
  • +------------------------------------+----------------------------------------------+
  • | • Fixed non-modulating restriction | • Modulates flow via mechanical diaphragm |
  • | • Flow varies with system pressures | • Maintains CONSTANT evaporator superheat |
  • | • Charged by TARGET SUPERHEAT | • Charged by SUBCOOLING method |
  • +------------------------------------+----------------------------------------------+
  • 1. Fixed Orifice Metering Devices (Piston / Capillary Tube)

A fixed orifice (such as a brass piston or precision capillary tube) provides a fixed hydraulic resistance. Mass flow rate depends entirely on high-to-low side pressure differential and liquid subcooling.

Operational Characteristic: Superheat fluctuates widely with heat load and outdoor ambient conditions.

Mandatory Charging Protocol: Systems equipped with fixed orifices MUST be charged using the Target Superheat Method . Target superheat is calculated from an industry chart using indoor wet-bulb temperature (evaporator load) and outdoor dry-bulb temperature (condenser load).

2. Thermostatic Expansion Valves (TXV)

A TXV is a mechanical modulating valve designed to maintain a constant evaporator superheat at the coil outlet, maximizing coil capacity while preventing liquid slugging.

The Three-Force Balance Equation

TXV position is governed by three opposing forces acting on the internal valve diaphragm: P 1 = P 2 + P 3 P_1 = P_2 + P_3 P 1 ​ = P 2 ​ + P 3 ​

Where:

P 1 P_1 P 1 ​ = Remote Sensing Bulb Pressure (Opening Force): Acts on top of the diaphragm. Increases as suction line temperature rises.

P 2 P_2 P 2 ​ = Evaporator Pressure (Closing Force): Acts on the underside of the diaphragm, pushing upward to close the valve.

P 3 P_3 P 3 ​ = Superheat Spring Pressure (Closing Force): Adjustable mechanical spring acting on the stem, pushing upward to close the valve. Remote Bulb Pressure P1 (Opening Force)

  • | | | | |
  • v v v v v
  • +---------------------+ <-- Flexible Diaphragm
  • +---------------------+
  • ^ ^ ^ ^ ^
  • | | | | |
  • Evaporator Pressure P2 + Spring Pressure P3
  • (Closing Forces)
  • Sensing Bulb Placement Rules

Mount the bulb on a clean, horizontal section of suction line immediately downstream of the evaporator outlet before any P-trap.

Orientation: Position at 4 o'clock or 8 o'clock on lines 7 / 8 ′ ′ 7/8^{\prime\prime} 7/ 8 ′′ OD and larger (prevents measuring oil accumulation along pipe bottom). Position at 1 o'clock or 2 o'clock on lines smaller than 7 / 8 ′ ′ 7/8^{\prime\prime} 7/ 8 ′′ OD.

Insulation: Insulation of 100% of the bulb body with waterproof insulation is mandatory to prevent ambient air temperature from corrupting bulb pressure.

Internal vs. External Equalizer Lines

Internal Equalizer: Internal port routes refrigerant pressure directly from the valve outlet to the underside of the diaphragm ( P 2 P_2 P 2 ​ ). Permissible only on small single-circuit coils with pressure drop < 2 psi <2\text{ psi} < 2 psi .

External Equalizer: A separate 1 / 4 ′ ′ 1/4^{\prime\prime} 1/ 4 ′′ copper line connects the underside of the TXV diaphragm to the suction line immediately downstream of the sensing bulb. Mandatory on evaporators using refrigerant distributors or coils with pressure drop > 2 psi >2\text{ psi} > 2 psi .

Exam Critical Rule: If an internally equalized TXV is installed on a coil with a distributor causing a 10 psi pressure drop, the high pressure at the valve outlet ( P 2 P_2 P 2 ​ ) pushes up on the diaphragm, forcing the valve prematurely closed and severely starving the evaporator. The external equalizer senses actual pressure at the coil outlet, compensating for distributor pressure drop.

Mandatory Charging Protocol: TXV-equipped systems MUST be charged using the Subcooling Method (typically 10°F to 15°F subcooling specified on the unit rating plate).

3. Electronic Expansion Valves (EEV)

EEVs utilize a bipolar stepper motor (typically 480 to 1,400 micro-steps) to position a needle valve orifice driven by a digital micro-controller. The controller receives inputs from a suction pressure transducer and a fast-response thermistor.

Control Precision: Maintains superheat within ± 0.5 ∘ F \pm 0.5^\circ\text{F} ± 0. 5 ∘ F of target setpoint across modulating inverter capacity ranges (10% to 100% load).

Efficiency Impact: Maximizes seasonal efficiency (SEER2, IEER), prevents superheat hunting, and closes tightly upon shutdown to prevent off-cycle refrigerant migration.

Metering Device Summary Table

Feature / Characteristic Fixed Orifice (Piston / Capillary) Thermostatic Expansion Valve (TXV) Electronic Expansion Valve (EEV)

Flow Control Principle Fixed hydraulic restriction Mechanical diaphragm force balance Microprocessor stepper motor position

Evaporator Superheat Fluctuates with load & ambient Constant (maintained mechanically) Constant (maintained electronically ± 0.5 ∘ F \pm 0.5^\circ\text{F} ± 0. 5 ∘ F )

Load Adaptability Poor (depends on pressure delta) Good (modulates to match thermal load) Exceptional (rapid micro-step positioning)

Mandatory Charging Method Target Superheat (Indoor WB / Outdoor DB) Subcooling (Rating plate value) Subcooling / Weigh-in Charge

Equalizer Requirement N/A External required for distributor coils Handled via suction pressure transducer

Target Applications Entry-level AC, Window Units Standard & High-SEER Split Systems, Heat Pumps VRF Systems, Inverter Chilling Plants