Study guide
2.3 Code Definitions & Trade Terminology
Texas Journeyman Plumber Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Licensing Laws, Board Rules, & Safety
1.1 TSBPE Laws, Board Rules, & Scope of Practice 1.2 Responsible Master Plumber (RMP) Supervision & Permitting 1.3 Jobsite Safety, OSHA Standards, & Trenching 1.4 Enforcement, Disciplinary Action, & Penalties
2 Chapter 2: Exam Format, Adopted Codes, & Definitions
2.1 Exam Format, Scoring, & Testing Logistics 2.2 Adopted Plumbing Codes & Jurisdictional Authority 2.3 Code Definitions & Trade Terminology
3 Chapter 3: General Regulations & Piping Installation
3.1 Approved Piping Materials & Standards 3.2 Pipe Hangers, Supports, & Spacing 3.3 Structural Protection, Sleeving, & Penetrations 3.4 System Testing & Inspection Requirements
4 Chapter 4: Drainage Systems & Pipe Sizing
4.1 Drainage Fixture Units (DFU) & Fixture Drains 4.2 Building Drains, Sewers, & Minimum Slopes 4.3 Cleanouts: Sizing, Clearances, & Locations 4.4 Sumps, Sewage Ejectors, & Indirect Waste Systems 4.5 Storm Drainage Systems
5 Chapter 5: Traps & Trap Seal Protection
5.1 Trap Design, Sizing, & Prohibited Traps 5.2 Trap Seal Protection, Trap Arms, & Trap Primers
6 Chapter 6: Venting Methods & Design
6.1 Vent Sizing, Developed Length, & Terminations 6.2 Individual, Common, & Relief Vents 6.3 Wet Venting, Circuit Venting, & Combination Systems 6.4 Air Admittance Valves (AAV) & Island Fixture Vents
7 Chapter 7: Potable Water Supply & Distribution
7.1 Water Supply Fixture Units (WSFU) & Pipe Sizing 7.2 Water Pressure, PRVs, & Thermal Expansion 7.3 Cross-Connection Control & Backflow Devices 7.4 Water Service, Metering, & System Disinfection
8 Chapter 8: Water Heaters & Scald Prevention
8.1 Water Heater Types, Sizing, & Installation 8.2 Temperature & Pressure (T&P) Relief Valves & Discharge 8.3 Combustion Air, Venting, & Scald-Prevention Mixing Valves
9 Chapter 9: Fuel Gas Piping Systems
9.1 Fuel Gas Properties & Piping Materials (IFGC / NFPA 54) 9.2 Gas Pipe Sizing & Longest Length Method 9.3 Gas Shutoff Valves, Regulators, & Pressure Testing
10 Chapter 10: Fixtures, Faucets, & Accessibility
10.1 Fixture Clearances & Accessibility Standards (ADA) 10.2 Water Conservation & Flush Rates 10.3 Urinals, Special Fixtures, & Interceptors 10.4 Fixture Fittings, Faucets, & Accessories
11 Chapter 11: Plumbing Math & Trade Calculations
11.1 45-Degree & Rolling Offset Calculations 11.2 Grade, Fall, & Invert Elevation Calculations 11.3 Volume, Capacity, & Hydrostatic Pressure Calculations
12 Chapter 12: Isometric Drawings & TSBPE Practical Exam
12.1 Isometric Drawing Principles & Piping Schematics 12.2 TSBPE 2-Story DWV Dollhouse Design & Layout 12.3 Water & Gas Piping Schematics for Practical Stations 12.4 Hands-On Shop Skills: Brazing, Soldering, & Flaring
2.3 Code Definitions & Trade Terminology
Key Takeaways Explain This Topic AI
The TSBPE review course tells candidates to begin with the code's definitions chapter, because the exam uses only correct code terms and never trade slang.
The building drain ends and the building sewer begins 30 inches outside the exterior building wall under the IPC (2 feet under the UPC).
A stack vent is the extension of a soil or waste stack above the highest branch; a vent stack is a separate pipe installed only to carry air.
Developed length is measured along the centerline of pipe and fittings, not as a straight-line distance between two points.
Flood level rim, critical level, trap weir, and branch interval are the four reference elevations that most dimensional code rules are measured from.
Last updated: August 2026
2.3 Code Definitions & Trade Terminology
Core Principle: The Board's own examination review course opens with this instruction: studying a plumbing code should begin with learning and understanding the proper plumbing terms and their meanings found in the chapter on definitions. The codes use only correct plumbing terms and contain no slang, and the examination is written the same way . A candidate who calls a closet bend a "toilet elbow" on the job will still read the word closet bend on the screen.
Many written items are pure definition questions. Many more are dimensional questions that are only answerable once you know which surface the dimension is measured from . This section covers both.
1. Drainage System Terms
Term Definition Boundary or limit to memorize
Building drain The lowest horizontal piping of a drainage system that receives the discharge from soil, waste, and other drainage pipes inside the walls of the building and conveys it to the building sewer Ends 30 inches outside the exterior wall (IPC); 2 feet outside the wall (UPC)
Building sewer That part of the drainage system extending from the end of the building drain and conveying discharge to a public sewer, private sewer, individual sewage disposal system, or other point of disposal Begins where the building drain ends
Soil pipe Pipe conveying the discharge of water closets, urinals, or fixtures having similar functions , with or without other fixtures Carries fecal matter
Waste pipe Pipe conveying only liquid waste free of fecal matter No water closets
Stack A general term for any vertical main of a soil, waste, or vent system extending through one or more stories Vertical only
Branch Any part of the piping system other than a main, riser, or stack Everything else
Horizontal branch drain A drain branch pipe extending laterally from a soil or waste stack, with or without vertical sections, that receives the discharge from one or more fixture drains Sized from Table 710.1(2) (IPC)
Fixture drain The drain from the trap of a fixture to the junction of that drain with any other drain pipe Starts at the trap outlet
Branch interval A vertical measurement of distance, 8 feet or more in developed length between the connections of horizontal branches to a drainage stack Roughly one story
Invert The lowest portion of the inside of any pipe or fitting that is not vertical Grade is set to inverts, not to pipe tops
2. Vent System Terms
The two most confused terms on any plumbing exam are stack vent and vent stack . They are not interchangeable.
Term Definition
Stack vent The extension of a soil or waste stack above the highest horizontal drain connected to that stack. It carries drainage below and air above.
Vent stack A separate vertical vent pipe installed only to provide air circulation to and from the drainage system. It never carries drainage.
Individual vent A vent that serves one fixture trap and connects to the vent system above the fixture or terminates outdoors
Common vent A single vent that serves two fixture drains installed at the same or different levels connecting at the same point
- Wet vent A pipe that serves as a vent for one fixture and a drain for another at the same time
- Relief vent A vent whose primary function is to provide air circulation between the drainage and vent systems
Yoke vent A pipe connecting upward from a soil or waste stack to a vent stack to prevent pressure changes in the stacks
Circuit vent A vent connecting to a horizontal branch drain serving a battery of fixtures , taken off in front of the last fixture connection
Developed length The length measured along the centerline of the pipe and fittings , not a straight-line distance
3. Water Supply and Cross-Connection Terms
Term Definition Why it matters
Potable water Water free from impurities in amounts sufficient to cause disease, meeting the requirements of the health authority The system this trade exists to protect
Cross-connection Any connection between a potable water system and any other source or system through which non-potable substances could enter the potable supply The root hazard
Backflow The reversal of flow of water or other liquids into the distribution pipes of the potable supply from any source The event
- Backsiphonage Backflow caused by negative or subatmospheric pressure in the potable system Vacuum-driven
- Backpressure Backflow caused by a downstream pressure greater than the supply pressure Pump- or boiler-driven
Air gap (water distribution) The unobstructed vertical distance through free atmosphere between the lowest opening of a supply outlet and the flood level rim of the receptor Minimum 2 pipe diameters, never less than 1 inch
Air break (drainage) A piping arrangement where a drain discharges indirectly into a receptacle below the flood level rim but above the trap seal Weaker than an air gap
Water service pipe The pipe from the water main or other source of potable supply to the water distribution system of the building Serves the whole building
Water distribution pipe The pipe within the structure that conveys water from the water service pipe to the points of use Downstream of the meter/valve
4. The Four Reference Elevations
Almost every dimensional rule in the code is measured from one of four surfaces. Confusing them is the fastest way to miss a question you actually knew. +---------------------------------------------------------------------------+
- | 1. FLOOD LEVEL RIM -- the top edge at which water can overflow the |
- | fixture or receptor. Vent rises, air gaps, and AAV heights measure |
- | FROM here. |
- | |
- | 2. CRITICAL LEVEL (C-L) -- the marked point on a vacuum breaker at or |
- | above which the device must be installed relative to the flood |
- | level rim of the fixture it protects. |
- | |
- | 3. TRAP WEIR -- the high point of the trap dip, over which water spills |
- | into the trap arm. Trap-to-vent distance measures FROM here. |
- | |
- | 4. TRAP SEAL -- the vertical depth of water between the crown weir and |
- | the top of the trap dip: 2 in minimum, 4 in maximum for standard |
- | traps. |
- +---------------------------------------------------------------------------+
- 5. Texas Licensing Terms (Board Rule 361.1)
The Board maintains its own definitions section, and the review course lists 22 TAC 361.1 as required reading for this exam.
Plumbing — the material and labor used in installing, maintaining, extending, or altering piping, fixtures, appliances, and appurtenances in connection with sanitary drainage, storm drainage, venting systems, and public or private water supply systems.
Direct supervision — the on-the-job oversight and direction of a registered Plumber's Apprentice or licensee by a licensed plumber who ensures that materials are prepared per the manufacturer's recommendations and the adopted code, and that the work is properly installed. A narrow exception added effective January 2025 permits remote, real-time audio-visual direct supervision for repair and replacement of existing fixtures not involving gas appliances on one- and two-family dwellings, and only for personnel meeting specific experience and registration criteria.
Responsible Master Plumber (RMP) — the Master Plumber designated by a plumbing company who is responsible for the company's plumbing work, holds the required certificate of insurance on file with the Board, and secures permits.
Approved / listed / labeled — carried over from the model codes: approved means acceptable to the authority having jurisdiction; listed means published in a list by an approved testing agency; labeled means bearing that agency's identifying mark.
6. Terminology Traps Seen on the Written Exam
"Sanitary tee" is not a "tee." A sanitary tee has a curved sweep in the branch and is permitted only horizontal-to-vertical. A straight (vent) tee is not a drainage fitting.
"Building trap" is not a "fixture trap." A building trap (house trap) is a running trap on the building drain and is generally prohibited unless the AHJ requires it.
"Grade" and "slope" are the same idea, but "grade" also means ground level. Read the sentence.
"Riser" means a water supply line rising one full story or more , not any vertical pipe.
"Main" is the principal artery of a system , to which branches connect — there are drainage mains, vent mains, and water mains.