Study guide

2.1 Exam Format, Scoring, & Testing Logistics

Texas Journeyman Plumber Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Licensing Laws, Board Rules, & Safety

1.1 TSBPE Laws, Board Rules, & Scope of Practice 1.2 Responsible Master Plumber (RMP) Supervision & Permitting 1.3 Jobsite Safety, OSHA Standards, & Trenching 1.4 Enforcement, Disciplinary Action, & Penalties

2 Chapter 2: Exam Format, Adopted Codes, & Definitions

2.1 Exam Format, Scoring, & Testing Logistics 2.2 Adopted Plumbing Codes & Jurisdictional Authority 2.3 Code Definitions & Trade Terminology

3 Chapter 3: General Regulations & Piping Installation

3.1 Approved Piping Materials & Standards 3.2 Pipe Hangers, Supports, & Spacing 3.3 Structural Protection, Sleeving, & Penetrations 3.4 System Testing & Inspection Requirements

4 Chapter 4: Drainage Systems & Pipe Sizing

4.1 Drainage Fixture Units (DFU) & Fixture Drains 4.2 Building Drains, Sewers, & Minimum Slopes 4.3 Cleanouts: Sizing, Clearances, & Locations 4.4 Sumps, Sewage Ejectors, & Indirect Waste Systems 4.5 Storm Drainage Systems

5 Chapter 5: Traps & Trap Seal Protection

5.1 Trap Design, Sizing, & Prohibited Traps 5.2 Trap Seal Protection, Trap Arms, & Trap Primers

6 Chapter 6: Venting Methods & Design

6.1 Vent Sizing, Developed Length, & Terminations 6.2 Individual, Common, & Relief Vents 6.3 Wet Venting, Circuit Venting, & Combination Systems 6.4 Air Admittance Valves (AAV) & Island Fixture Vents

7 Chapter 7: Potable Water Supply & Distribution

7.1 Water Supply Fixture Units (WSFU) & Pipe Sizing 7.2 Water Pressure, PRVs, & Thermal Expansion 7.3 Cross-Connection Control & Backflow Devices 7.4 Water Service, Metering, & System Disinfection

8 Chapter 8: Water Heaters & Scald Prevention

8.1 Water Heater Types, Sizing, & Installation 8.2 Temperature & Pressure (T&P) Relief Valves & Discharge 8.3 Combustion Air, Venting, & Scald-Prevention Mixing Valves

9 Chapter 9: Fuel Gas Piping Systems

9.1 Fuel Gas Properties & Piping Materials (IFGC / NFPA 54) 9.2 Gas Pipe Sizing & Longest Length Method 9.3 Gas Shutoff Valves, Regulators, & Pressure Testing

10 Chapter 10: Fixtures, Faucets, & Accessibility

10.1 Fixture Clearances & Accessibility Standards (ADA) 10.2 Water Conservation & Flush Rates 10.3 Urinals, Special Fixtures, & Interceptors 10.4 Fixture Fittings, Faucets, & Accessories

11 Chapter 11: Plumbing Math & Trade Calculations

11.1 45-Degree & Rolling Offset Calculations 11.2 Grade, Fall, & Invert Elevation Calculations 11.3 Volume, Capacity, & Hydrostatic Pressure Calculations

12 Chapter 12: Isometric Drawings & TSBPE Practical Exam

12.1 Isometric Drawing Principles & Piping Schematics 12.2 TSBPE 2-Story DWV Dollhouse Design & Layout 12.3 Water & Gas Piping Schematics for Practical Stations 12.4 Hands-On Shop Skills: Brazing, Soldering, & Flaring

2.1 Exam Format, Scoring, & Testing Logistics

Key Takeaways Explain This Topic AI

The Journeyman written exam is 100 multiple-choice questions in 120 minutes; the practical is 6 stations in 240 minutes.

A score of 70 percent is required to pass, and an exam with a practical component is not an overall pass until both portions are passed.

Pearson VUE charges $68.50 for the written exam and $40.00 for the practical; the TSBPE application fee is a separate $40.

A current Tradesman Plumber-Limited licensee moving up to Journeyman takes the written exam only and does not repeat the practical.

No books, notes, scratch paper, or reference materials are allowed in the testing room — the written exam is entirely closed-book.

Last updated: August 2026

2.1 Exam Format, Scoring, & Testing Logistics

Core Principle: The Texas Journeyman Plumber License is earned through a two-part examination . Pearson VUE delivers the computer-based written portion at commercial test centers; the Texas State Board of Plumbing Examiners (TSBPE) delivers the hands-on practical portion at its own Austin and Waco testing centers. You must pass the written portion before the practical will even be scheduled, and the exam is not an overall pass until both portions are cleared.

Candidates lose seats every year to logistics rather than plumbing knowledge — arriving with a code book they cannot use, budgeting the wrong fee, or misjudging how many minutes they have per question. Treat this section as the operational checklist that protects the technical work you do in the rest of this guide.

1. Exam Structure at a Glance

Portion Items Time Allotted Fee (paid to Pearson VUE) Where it is administered

Written (computer-based) 100 multiple-choice questions 120 minutes (2 hours) $68.50 Any authorized Pearson VUE test center, including on-base military sites

Practical (hands-on) 6 stations 240 minutes (4 hours) $40.00 TSBPE Austin and Waco testing centers only

One hundred questions in 120 minutes averages 1 minute 12 seconds per item . That is generous for a recall question and tight for a multi-step sizing or offset calculation, so the practical strategy is to bank time on the definitional and code-lookup items in order to spend it on the math.

Fees You Will Actually Pay

  • Payment Amount Paid to When
  • Journeyman examination application fee $40 TSBPE With the application, before authorization
  • Written examination fee $68.50 Pearson VUE At the time you reserve the seat
  • Practical examination fee $40.00 Pearson VUE (scheduling) At the time you reserve the practical date
  • Initial license fee $40 TSBPE After passing both portions

Examination fees are non-refundable and non-transferable except under the published change/cancel policy, and payment is never accepted at the test center door.

2. Scoring and the Pass Standard

Passing score: 70 percent. The score report is marked simply pass or fail .

Where the exam includes a practical component, the examination is not considered an overall pass until both the written and practical portions have been passed .

A failing report includes a numeric score plus diagnostic feedback by content area . That breakdown is a study aid only — the Board cautions candidates to review all content areas before retesting, because a small sample of items in one area is not a reliable measure of that area.

Written scores reach TSBPE from Pearson VUE within about 48 hours . Passing candidates then receive a second Authorization to Test email clearing them to book the practical in Austin or Waco.

3. The Tradesman-to-Journeyman Exemption

This single rule changes the entire preparation plan for thousands of Texas candidates:

A candidate who is already a currently licensed Tradesman Plumber-Limited at the time of examination has already demonstrated competency on the shop work and the sanitary drainage and vent model. That candidate's Journeyman examination is limited to the written portion and does not include the hands-on shop stations or the two-story DWV model.

A registered Plumber's Apprentice going straight to Journeyman takes both portions. Note the Board's own advice, though: even exempt Tradesman candidates should study the design, installation, and material-preparation material, because those same concepts are tested in written form.

4. Retake Rules and Authorization Windows

  • Rule Requirement
  • Attempts per authorization Up to five attempts on the written portion
  • Authorization lifespan All attempts must be completed within one year of the initial TSBPE authorization
  • Wait after 1st failure 30 days
  • Wait after 2nd failure 60 days
  • Wait after each later failure 90 days

Rescheduling Cannot be booked at the test center; wait 24 hours , then reschedule through your Pearson VUE account

Reapplying to TSBPE Do not reapply for a new authorization until all five attempts are exhausted

Practical examination dates must be reserved at least ten days in advance, and accommodation requests for the practical go directly to TSBPE rather than to Pearson VUE.

5. Test-Center Rules That Disqualify Candidates

Reference materials are prohibited. Dictionaries, books, papers — including scratch paper you bring — and notes are not permitted in the examination room. The written exam is closed-book ; the administrator issues note-taking materials at the workstation, and you may not write on them before the exam starts or remove them afterward.

No personal items. Phones, smart watches, wallets, bags, hats, and calculators of your own are stored outside the room. Expect to empty your pockets and pat down.

Report 30 minutes early , with acceptable government-issued photo identification. Late or absent candidates who did not cancel properly forfeit the fee.

Fingerprints are required for every license type before an application is approved.

At the practical stations, TSBPE furnishes all materials. Short pants and open-toed shoes are not allowed in the examination area — no exceptions.

6. How to Convert These Rules into a Study Plan

Because the written exam is closed-book, memorization of tables matters more in Texas than in open-book states . Drill drainage fixture unit values, minimum slopes, trap sizes, hanger spacing, and vent distances until they are recall, not lookup.

Because the exam is not tied to a single model code (see Section 2.2), pick the code family your jurisdiction uses, learn it cold, and then learn the handful of places where the other code's number differs.

Because the practical is a separate 4-hour, 6-station event, schedule dedicated shop practice — solvent-cement, solder, braze, thread, and cast-iron band joints — instead of assuming written study transfers.

Because retake waits escalate from 30 to 60 to 90 days, a failed first attempt can cost a full quarter of earning power. The cheapest attempt is the prepared one.