Study guide
3.1 Approved Piping Materials & Standards
Texas Journeyman Plumber Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Licensing Laws, Board Rules, & Safety
1.1 TSBPE Laws, Board Rules, & Scope of Practice 1.2 Responsible Master Plumber (RMP) Supervision & Permitting 1.3 Jobsite Safety, OSHA Standards, & Trenching 1.4 Enforcement, Disciplinary Action, & Penalties
2 Chapter 2: Exam Format, Adopted Codes, & Definitions
2.1 Exam Format, Scoring, & Testing Logistics 2.2 Adopted Plumbing Codes & Jurisdictional Authority 2.3 Code Definitions & Trade Terminology
3 Chapter 3: General Regulations & Piping Installation
3.1 Approved Piping Materials & Standards 3.2 Pipe Hangers, Supports, & Spacing 3.3 Structural Protection, Sleeving, & Penetrations 3.4 System Testing & Inspection Requirements
4 Chapter 4: Drainage Systems & Pipe Sizing
4.1 Drainage Fixture Units (DFU) & Fixture Drains 4.2 Building Drains, Sewers, & Minimum Slopes 4.3 Cleanouts: Sizing, Clearances, & Locations 4.4 Sumps, Sewage Ejectors, & Indirect Waste Systems 4.5 Storm Drainage Systems
5 Chapter 5: Traps & Trap Seal Protection
5.1 Trap Design, Sizing, & Prohibited Traps 5.2 Trap Seal Protection, Trap Arms, & Trap Primers
6 Chapter 6: Venting Methods & Design
6.1 Vent Sizing, Developed Length, & Terminations 6.2 Individual, Common, & Relief Vents 6.3 Wet Venting, Circuit Venting, & Combination Systems 6.4 Air Admittance Valves (AAV) & Island Fixture Vents
7 Chapter 7: Potable Water Supply & Distribution
7.1 Water Supply Fixture Units (WSFU) & Pipe Sizing 7.2 Water Pressure, PRVs, & Thermal Expansion 7.3 Cross-Connection Control & Backflow Devices 7.4 Water Service, Metering, & System Disinfection
8 Chapter 8: Water Heaters & Scald Prevention
8.1 Water Heater Types, Sizing, & Installation 8.2 Temperature & Pressure (T&P) Relief Valves & Discharge 8.3 Combustion Air, Venting, & Scald-Prevention Mixing Valves
9 Chapter 9: Fuel Gas Piping Systems
9.1 Fuel Gas Properties & Piping Materials (IFGC / NFPA 54) 9.2 Gas Pipe Sizing & Longest Length Method 9.3 Gas Shutoff Valves, Regulators, & Pressure Testing
10 Chapter 10: Fixtures, Faucets, & Accessibility
10.1 Fixture Clearances & Accessibility Standards (ADA) 10.2 Water Conservation & Flush Rates 10.3 Urinals, Special Fixtures, & Interceptors 10.4 Fixture Fittings, Faucets, & Accessories
11 Chapter 11: Plumbing Math & Trade Calculations
11.1 45-Degree & Rolling Offset Calculations 11.2 Grade, Fall, & Invert Elevation Calculations 11.3 Volume, Capacity, & Hydrostatic Pressure Calculations
12 Chapter 12: Isometric Drawings & TSBPE Practical Exam
12.1 Isometric Drawing Principles & Piping Schematics 12.2 TSBPE 2-Story DWV Dollhouse Design & Layout 12.3 Water & Gas Piping Schematics for Practical Stations 12.4 Hands-On Shop Skills: Brazing, Soldering, & Flaring
3.1 Approved Piping Materials & Standards
Key Takeaways Explain This Topic AI
Plumbing material standards in Texas are governed by consensus organizations including ASTM, ASME, CSA, and NSF, with all potable water components requiring mandatory certification to NSF/ANSI 14, NSF/ANSI 61, and NSF/ANSI 372 lead-free standards (maximum 0.25% weighted average lead content).
Seamless copper water tube (ASTM B88) is classified into three standardized wall thickness grades identified by colored markings: Type K (Green, thickest wall; approved for underground burial, water services, and high-pressure lines), Type L (Blue, medium wall; standard for interior water distribution and underground), and Type M (Red, thinnest wall; approved strictly for aboveground interior water distribution, prohibited underground).
Plastic piping standards mandate ASTM D2665 for PVC-DWV, ASTM D2846 for CPVC hot/cold distribution, and ASTM F876/F877 for cross-linked polyethylene (PEX), with PEX temperature-pressure ratings standardized at 160 psi at 73.4°F, 100 psi at 180°F, and 80 psi at 200°F.
Solvent cementing of PVC-DWV systems requires a two-step process utilizing purple primer conforming to ASTM F656 to chemically soften and penetrate mating surfaces, followed immediately by solvent cement conforming to ASTM D2564 while wet.
Cast iron soil pipe is specified as hub-and-spigot service weight (ASTM A74) joined with ASTM C564 compression gaskets or hubless (CISPI 301 / ASTM A888) joined with CISPI 310 shielded couplings torqued to 60 in-lb (or 80 in-lb for heavy-duty ASTM C1540 couplings).
Last updated: August 2026
3.1 Approved Piping Materials & Standards
In the State of Texas, the Texas State Board of Plumbing Examiners (TSBPE) enforces strict adherence to model plumbing codes—principally the International Plumbing Code (IPC) and the Uniform Plumbing Code (UPC) , as adopted by local municipalities—to safeguard public health, sanitation, and safety. Every piping component installed in a plumbing system, from municipal water service lines to drainage stacks and vent terminals, must conform to recognized national consensus standards.
A journeyman plumber must possess an exact, nuanced understanding of material specifications, physical properties, limitations, third-party certification markings, and approved joining methods. Installing unapproved materials or utilizing incorrect joining procedures compromises structural integrity, contaminates potable water supplies, and results in immediate inspection failure.
1. Standards Organizations & Health Certifications
Plumbing materials are tested and certified by recognized standards development and testing organizations. The following marks and standards must appear stamped or incised on piping and fittings: +-----------------------------------------------------------------------------------+
- | MAJOR PLUMBING STANDARDS BODIES |
- | |
- | [ASTM] American Society for Testing and Materials (Material specifications) |
- | [ASME] American Society of Mechanical Engineers (Fixtures, valves, fittings) |
- | [ANSI] American National Standards Institute (Overarching standard coordinator)|
- | [NSF] National Sanitation Foundation (Health effects, toxicology, plastic pipe)|
- | [CISPI] Cast Iron Soil Pipe Institute (Hubless cast iron standards) |
- | [CSA] Canadian Standards Association (Dual US/Canada harmonized certifications)|
- +-----------------------------------------------------------------------------------+
- Critical Potable Water Certifications
NSF/ANSI Standard 14 ( Plumbing System Components and Related Materials ): Evaluates physical, performance, and quality control requirements for plastic piping components.
NSF/ANSI Standard 61 ( Drinking Water System Components – Health Effects ): Evaluates the chemical leaching and toxicological impact of all materials contacting potable drinking water.
NSF/ANSI Standard 372 ( Drinking Water System Components – Lead Content ): Verifies compliance with the federal Safe Drinking Water Act (SDWA) Lead-Free Mandate , certifying that the wetted surface area of pipes, fittings, and fixtures contains a maximum weighted average lead content of ≤ 0.25% .
Solder & Flux Lead Limits: Solder and flux used on potable water lines must be certified lead-free under ASTM B32 (solder alloys containing ≤ 0.2% lead) and ASTM B813 (water-flushable soldering flux).
2. Copper Water Tube & Copper Alloy Systems
Seamless copper water tube is manufactured in accordance with ASTM B88 ( Standard Specification for Seamless Copper Water Tube ). Copper is non-permeable, corrosion-resistant, biostatic (inhibits bacterial growth), and capable of withstanding high internal operating pressures. +-----------------------------------------------------------------------------------+
- | COPPER WATER TUBE (ASTM B88) CLASSIFICATIONS |
- | |
- | TYPE K [GREEN MARKING] - Extra Heavy / Thickest Wall |
- | - Uses: Underground water services, under-slab, high-pressure lines |
- | |
- | TYPE L [BLUE MARKING] - Medium Wall Thickness (Standard Trade Workhorse) |
- | - Uses: Interior domestic hot/cold water distribution, underground lines|
- | |
- | TYPE M [RED MARKING] - Light / Thinnest Wall Thickness |
- | - Uses: Aboveground interior domestic water distribution ONLY |
- | - PROHIBITED: Underground burial and under-slab installations |
- | |
- | TYPE DWV [YELLOW MARKING]- Drainage, Waste, & Vent (ASTM B306) Non-Pressure |
- | - Uses: Aboveground drainage, waste, and vent piping only |
- +-----------------------------------------------------------------------------------+
- Copper Tube Characteristics & Dimensional Comparison
- Specification Type K (Green) Type L (Blue) Type M (Red) Type DWV (Yellow)
- Relative Wall Thickness Thickest (100%) Medium (≈ 65–75%) Thinnest (≈ 45–55%) Extra Light (Non-pressure)
- Approved Underground? YES (Ideal for burial) YES (Approved) NO (Strictly Prohibited) NO (Prohibited)
- Approved Aboveground? YES YES YES YES (DWV Only)
Standard Tempers Drawn (Hard) / Annealed (Soft) Drawn (Hard) / Annealed (Soft) Drawn (Hard) / Annealed (Soft) Drawn (Hard) Only
- Governing ASTM Standard ASTM B88 ASTM B88 ASTM B88 ASTM B306
- 3/4" Nom. Wall Thickness 0.065 in 0.045 in 0.032 in N/A (DWV starts at 1-1/4")
Important
Exam Rule for Copper Underground: Under both IPC and UPC, Type M copper is never permitted underground or embedded in concrete slabs . Only Type K and Type L copper tube (annealed soft temper with no joints under slab except brazed where allowed) are approved for subterranean potable water services.
Copper Joining Methodologies
Soldered Joints (Sweat Joints):
Tube ends cut square, reamed to full inside diameter, cleaned with abrasive mesh to bright metal, coated with water-flushable flux ( ASTM B813 ), and joined using lead-free solder ( ASTM B32 ) at temperatures between 400°F and 500°F (204°C to 260°C).
Brazed Joints (Hard Solder):
High-temperature joining utilizing copper-phosphorus (BCuP series) or silver (BAg series) brazing filler rods at temperatures exceeding 1,000°F (538°C) .
BCuP alloys do not require flux on copper-to-copper joints; flux is required on copper-to-brass joints.
Brazing is mandatory for concealed joints in medical gas piping, under-slab water lines where joints cannot be avoided, and refrigeration systems.
Press-Connect Fittings (ASME B16.51):
Mechanical press joining utilizing calibrated electro-hydraulic jaws and copper fittings with internal EPDM O-rings, rated up to 200 psi and 250°F.
Push-Fit Fittings (ASSE 1061):
Removable mechanical fittings utilizing stainless steel grab rings and EPDM seals, approved for exposed and accessible locations (concealed use subject to local jurisdiction approval).
Flared Mechanical Joints (ASTM B280 / SAE J513):
45° flared fittings utilized with annealed (soft) copper tubing, common in gas supply lines and underground water service connections.
3. Plastic Piping Materials & Specifications
Thermoplastic piping dominates modern residential and commercial plumbing due to its low cost, smooth interior walls (Hazen-Williams coefficient C=150), chemical resistance, and resistance to scale buildup. +-----------------------------------------------------------------------------------+
- | PLASTIC PIPING SUMMARY & STANDARDS |
- | |
- | [PVC-DWV] ASTM D2665 - Polyvinyl Chloride Drainage, Waste, & Vent |
- | [PVC SCH 40]ASTM D1785 - Polyvinyl Chloride Cold-Water Pressure Piping |
- | [CPVC] ASTM D2846 - Chlorinated Polyvinyl Chloride (Hot & Cold Potable) |
- | [PEX] ASTM F876 - Cross-linked Polyethylene Tubing (Performance) |
- | ASTM F877 - Cross-linked Polyethylene System Standard |
- | [ABS-DWV] ASTM D2661 - Acrylonitrile-Butadiene-Styrene DWV Piping |
- | [PE-RT] ASTM F2769 - Polyethylene of Raised Temperature Resistance |
- +-----------------------------------------------------------------------------------+
- Polyvinyl Chloride (PVC)
ASTM D2665: Standard for PVC drainage, waste, and vent (DWV) piping.
ASTM D1785: Standard for Schedule 40 and Schedule 80 PVC pressure piping.
Thermal Limitation: Maximum continuous operating temperature of 140°F (60°C) . PVC is strictly prohibited for interior hot water distribution and cannot be used for building interior water supplies carrying heated water.
Safety Mandate: PVC is strictly prohibited for compressed air or pressurized gases due to explosive brittle shattering hazards.
Chlorinated Polyvinyl Chloride (CPVC)
ASTM D2846: Standard for Copper Tube Size (CTS) SDR 11 CPVC hot and cold domestic water distribution.
ASTM F441 / F442: Standard for Schedule 40/80 and IPS-dimensioned CPVC industrial pipe.
Performance Ratings: Rated for 100 psi at 180°F (82°C) and 400 psi at 73.4°F (23°C) .
Thermal Transition: Must maintain a minimum clearance of 6 to 12 inches of metallic piping or approved flexible connectors between a water heater tank and CPVC piping to prevent thermal degradation from radiant flue heat.
Cross-Linked Polyethylene (PEX)
ASTM F876 / ASTM F877: Material performance and system integration standards.
PEX Manufacturing Methods:
PEX-a (Engel Method / Peroxide): Highest degree of cross-linking (>85%); provides superior flexibility, kink memory (repairable with heat gun), and expansion capability.
PEX-b (Silane / Moisture Cure Method): Medium cross-linking (65–70%); higher tensile strength and burst pressure resistance.
PEX-c (Electronic Beam / Radiation Method): Cross-linking (70–75%) achieved through electron beam bombardment; eco-friendly manufacturing.
Temperature and Pressure Ratings:
- 160 psi at 73.4°F (23°C)
- 100 psi at 180°F (82°C)
- 80 psi at 200°F (93°C)
Fitting Standards:
ASTM F1807: Metal crimp ring fittings utilizing copper crimp rings.
ASTM F2159: Engineered polymer (plastic) crimp fittings.
ASTM F1960: Cold expansion fittings with PEX reinforcing rings (ProPEX / Uponor style).
ASTM F2080: Cold expansion with metal compression sleeves.
Installation Safeguards: PEX must be shielded from direct sunlight (UV exposure degrades polymer chains within 30 to 60 days unless specifically UV-stabilized).
Acrylonitrile-Butadiene-Styrene (ABS)
ASTM D2661: Standard for ABS DWV piping.
Properties: Rigid black plastic piping; joined via a one-step solvent cement ( ASTM D2235 ) without primer.
Transition Joining: Direct solvent cementing between ABS and PVC is prohibited on commercial installations unless using approved mechanical shielded transition couplings ( ASTM C1460 ) or specialized dual-rated transition cement strictly where approved by the local AHJ.
4. Cast Iron Soil Pipe & Mechanical Couplings
Cast iron soil pipe remains the premier material for commercial drainage, multi-story acoustic dampening, and high-temperature waste discharge. +-----------------------------------------------------------------------------------+
- | CAST IRON SOIL PIPE SPECIFICATIONS |
- | |
- | [HUB-AND-SPIGOT] ASTM A74 - Service Weight (SV) & Extra Heavy (XH) |
- | - Joined with ASTM C564 Neoprene Compression Gaskets |
- | - Traditional: Lead and Oakum caulked joints |
- | |
- | [HUBLESS / NO-HUB]CISPI 301 / ASTM A888 - Hubless Cast Iron Soil Pipe & Fittings |
- | - Joined with CISPI 310 Shielded Couplings (60 in-lb torque) |
- | - Heavy-Duty: ASTM C1540 Couplings (80 in-lb torque) |
- +-----------------------------------------------------------------------------------+
- Joining Hubless Cast Iron Pipe
Standard Shielded Couplings (CISPI 310 / ASTM C1277): Consist of a corrugated stainless steel shield, neoprene/elastomeric gasket, and stainless steel worm-drive bands tightened to 60 in-lb of torque using a calibrated torque wrench.
Heavy-Duty Shielded Couplings (ASTM C1540): Feature a wider, thicker stainless steel shield with 4 to 6 clamping bands tightened to 80 in-lb of torque, providing superior shear resistance and joint deflection protection in high-rise and underground installations.
Compression Gasket Joints (ASTM C564): Utilized for ASTM A74 hub-and-spigot pipe, where a molded elastomeric gasket is inserted into the hub and the spigot end is lubricated and driven home with a puller.
5. Chemical Solvent Cementing & Primer Requirements
Solvent cementing creates a chemical weld between thermoplastic pipe and fitting sockets by dissolving the resin matrices, allowing the polymer chains to intermingle before the solvent evaporates. +-----------------------------------------------------------------------------------+
- | SOLVENT CEMENTING 4-STEP WELDING PROCEDURE |
- | |
- | [STEP 1: PREPARATION] Square cut, deburr inside, chamfer outside 10-15° |
- | [STEP 2: PRIMING] Apply ASTM F656 Purple Primer (Softens surface) |
- | [STEP 3: CEMENTING] Apply ASTM D2564 PVC Cement aggressively while wet |
- | [STEP 4: ASSEMBLY] Insert immediately, quarter-turn (90°), hold 30 seconds |
- +-----------------------------------------------------------------------------------+
Code Rules for Primer & Cement:
Primer Standard (ASTM F656): Mandatory purple-dyed primer on all PVC installations to provide code inspectors with instant visual verification of chemical penetration.
Cement Standards:
ASTM D2564: Solvent cement for Polyvinyl Chloride (PVC) systems.
ASTM D2846 / F493: Solvent cement for Chlorinated Polyvinyl Chloride (CPVC) systems (typically orange or yellow).
ASTM D2235: Solvent cement for Acrylonitrile-Butadiene-Styrene (ABS) systems (black; no primer required).
Exemption: The IPC permits clear primer on non-pressure PVC-DWV piping in sizes up to 4 inches in residential applications where permitted by the local plumbing inspector, but commercial codes and TSBPE testing standards emphasize universal purple primer compliance.
Cold Weather Cementing: At temperatures below 40°F (4°C), cure times increase significantly (up to 24–48 hours before pressure testing), and aggressive priming is required to achieve proper surface softening.
6. Materials & Standards Master Reference Table
Material Application Relevant Standards Common Joining Methods Critical Code Restrictions
Copper Type K Water Service, Underground, Under-Slab, Interior ASTM B88, NSF 61/372 Brazing, Soldering (ASTM B32), Press (ASME B16.51), Flared Green mark; annealed coils preferred for underground burial without joints.
Copper Type L Interior Distribution, Aboveground & Underground ASTM B88, NSF 61/372 Soldering, Brazing, Press-connect, Push-fit Blue mark; standard commercial/residential water line material.
Copper Type M Aboveground Interior Distribution ONLY ASTM B88, NSF 61/372 Soldering, Press-connect, Push-fit Red mark; STRICTLY PROHIBITED underground or in concrete .
PVC-DWV Drainage, Waste, Vent (DWV) ASTM D2665, NSF 14 Solvent Cement (ASTM D2564) + Primer (ASTM F656) Max temp 140°F; prohibited for hot water and compressed air.
CPVC Potable Hot & Cold Water Distribution ASTM D2846, NSF 14/61/372 Solvent Cement (ASTM F493), Mechanical Flange Rated 100 psi at 180°F; require metallic transition at water heater.
PEX (a, b, c) Potable Hot & Cold Water Distribution ASTM F876, F877, NSF 14/61 Crimp (F1807/F2159), Expansion (F1960/F2080) UV sensitive; protect from direct sunlight; continuous support required.
ABS-DWV Drainage, Waste, Vent (DWV) ASTM D2661, NSF 14 One-step Solvent Cement (ASTM D2235) Cannot solvent-weld directly to PVC without approved transition coupling.
Cast Iron Sanitary DWV, Storm Drainage CISPI 301, ASTM A74, ASTM A888 Shielded Couplings (CISPI 310), Compression Gaskets Torqued to 60 in-lb (80 in-lb for ASTM C1540 heavy duty).