Study guide
1.3 Jobsite Safety, OSHA Standards, & Trenching
Texas Journeyman Plumber Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Licensing Laws, Board Rules, & Safety
1.1 TSBPE Laws, Board Rules, & Scope of Practice 1.2 Responsible Master Plumber (RMP) Supervision & Permitting 1.3 Jobsite Safety, OSHA Standards, & Trenching 1.4 Enforcement, Disciplinary Action, & Penalties
2 Chapter 2: Exam Format, Adopted Codes, & Definitions
2.1 Exam Format, Scoring, & Testing Logistics 2.2 Adopted Plumbing Codes & Jurisdictional Authority 2.3 Code Definitions & Trade Terminology
3 Chapter 3: General Regulations & Piping Installation
3.1 Approved Piping Materials & Standards 3.2 Pipe Hangers, Supports, & Spacing 3.3 Structural Protection, Sleeving, & Penetrations 3.4 System Testing & Inspection Requirements
4 Chapter 4: Drainage Systems & Pipe Sizing
4.1 Drainage Fixture Units (DFU) & Fixture Drains 4.2 Building Drains, Sewers, & Minimum Slopes 4.3 Cleanouts: Sizing, Clearances, & Locations 4.4 Sumps, Sewage Ejectors, & Indirect Waste Systems 4.5 Storm Drainage Systems
5 Chapter 5: Traps & Trap Seal Protection
5.1 Trap Design, Sizing, & Prohibited Traps 5.2 Trap Seal Protection, Trap Arms, & Trap Primers
6 Chapter 6: Venting Methods & Design
6.1 Vent Sizing, Developed Length, & Terminations 6.2 Individual, Common, & Relief Vents 6.3 Wet Venting, Circuit Venting, & Combination Systems 6.4 Air Admittance Valves (AAV) & Island Fixture Vents
7 Chapter 7: Potable Water Supply & Distribution
7.1 Water Supply Fixture Units (WSFU) & Pipe Sizing 7.2 Water Pressure, PRVs, & Thermal Expansion 7.3 Cross-Connection Control & Backflow Devices 7.4 Water Service, Metering, & System Disinfection
8 Chapter 8: Water Heaters & Scald Prevention
8.1 Water Heater Types, Sizing, & Installation 8.2 Temperature & Pressure (T&P) Relief Valves & Discharge 8.3 Combustion Air, Venting, & Scald-Prevention Mixing Valves
9 Chapter 9: Fuel Gas Piping Systems
9.1 Fuel Gas Properties & Piping Materials (IFGC / NFPA 54) 9.2 Gas Pipe Sizing & Longest Length Method 9.3 Gas Shutoff Valves, Regulators, & Pressure Testing
10 Chapter 10: Fixtures, Faucets, & Accessibility
10.1 Fixture Clearances & Accessibility Standards (ADA) 10.2 Water Conservation & Flush Rates 10.3 Urinals, Special Fixtures, & Interceptors 10.4 Fixture Fittings, Faucets, & Accessories
11 Chapter 11: Plumbing Math & Trade Calculations
11.1 45-Degree & Rolling Offset Calculations 11.2 Grade, Fall, & Invert Elevation Calculations 11.3 Volume, Capacity, & Hydrostatic Pressure Calculations
12 Chapter 12: Isometric Drawings & TSBPE Practical Exam
12.1 Isometric Drawing Principles & Piping Schematics 12.2 TSBPE 2-Story DWV Dollhouse Design & Layout 12.3 Water & Gas Piping Schematics for Practical Stations 12.4 Hands-On Shop Skills: Brazing, Soldering, & Flaring
1.3 Jobsite Safety, OSHA Standards, & Trenching
Key Takeaways Explain This Topic AI
OSHA 29 CFR 1926 Subpart P requires an approved protective system (sloping, benching, shoring, or shielding) for all excavations 5 feet or deeper, unless in solid rock.
Soil is classified into Stable Rock (vertical), Type A (0.75:1 slope or 53°), Type B (1:1 slope or 45°), and Type C (1.5:1 slope or 34°); benching is strictly prohibited in Type C soil.
Excavations 4 feet or deeper require safe access/egress (ladders or ramps) within 25 feet of lateral worker travel, with ladders extending at least 3 feet above the upper landing.
Excavated spoil piles, tools, and heavy machinery must be kept at least 2 feet back from the edge of the excavation.
Atmospheric testing for oxygen deficiency (<19.5%), flammable gases (>10% LEL), and toxic gases (H2S, CO) is mandatory before workers enter excavations deeper than 4 feet where hazardous atmospheres could exist.
Last updated: August 2026
1.3 Jobsite Safety, OSHA Standards, & Trenching
Core Principle: Underground utility installation, building sewer connections, and commercial rough-ins expose plumbers to extreme hazards, including trench cave-ins, hazardous atmospheres, and structural collapse. Under OSHA 29 CFR 1926 Subpart P , employers must implement strict engineering controls, designated competent person oversight, and protective systems before any worker enters an excavation.
The OSHA Competent Person Mandate
OSHA defines a Competent Person as an individual capable of identifying existing and predictable hazards in the surroundings, or working conditions that are unsanitary, hazardous, or dangerous to employees, and who has the specific authorization to take prompt corrective measures to eliminate them.
Responsibilities of the Competent Person in Excavations
Daily Site Inspections: Must inspect excavations, adjacent areas, and protective systems daily prior to the start of work , as well as after every rainstorm, freeze/thaw cycle, vibration event, or hazard-increasing occurrence.
Soil Testing: Must perform at least one visual analysis and at least one manual test (e.g., thumb penetration test, pocket penetrometer, or shearvane) to classify soil type accurately.
Stop-Work Authority: Has absolute authority to remove workers from the trench immediately upon identifying any evidence of cave-in risk, tension cracks, sloughing, boiling, or atmospheric danger. +-------------------------------------------------------------------------+
- | CRITICAL EXCAVATION SAFETY RULES |
- +-------------------------------------------------------------------------+
- | Depth >= 4 Feet --> Safe Access/Egress Required (Ladders within 25 ft) |
- | Depth >= 4 Feet --> Atmospheric Testing Required (if hazard suspected) |
- | Depth >= 5 Feet --> Protective System MANDATORY (Sloping/Shoring/Box) |
- | Edge Setback --> Spoil Piles & Equipment Minimum 2 Feet from Edge |
- | Ladder Height --> Must Extend at least 3 Feet Above Landing Surface |
- +-------------------------------------------------------------------------+
- Soil Classification System
OSHA categorizes all soils into four distinct classes based on cohesive strength, soil stability, and compressive strength measured in tons per square foot (tsf) .
Soil Classification Unconfined Compressive Strength Soil Characteristics & Examples Restrictions & Conditions
Stable Rock Solid Mineral Matrix Natural solid mineral matter that can be excavated with vertical sides Can remain vertical (90°) without protective systems.
Type A Soil ≥ 1.5 tsf (144 kPa) Cohesive soils: clay, silty clay, sandy clay, clay loam Cannot be classified as Type A if: (1) it is fissured; (2) subject to heavy traffic vibration; (3) previously disturbed; or (4) water is seeping into the trench.
Type B Soil >0.5 tsf and <1.5 tsf Cohesive soil (silt, silt loam) and granular cohesionless soil (angular gravel, silt, crushed rock); previously disturbed Type A soil; fissured/vibrating Type A Moderate stability. Sloping ratio 1:1 (45°). Benching allowed up to 4 ft high.
Type C Soil ≤ 0.5 tsf (48 kPa) Granular soils (sand, gravel, loamy sand); submerged soil; soil with freely seeping water; unstable submerged rock Lowest stability. Sloping ratio 1.5:1 (34°). Benching is NEVER permitted in Type C soil.
Excavation Protective Systems: Sloping, Benching, & Shielding
Under OSHA 29 CFR 1926.652 , every trench 5 feet or deeper must have an approved protective system unless the excavation is made entirely in stable rock. For trenches under 5 feet, protection is required if the competent person finds potential cave-in hazards.
1. Maximum Allowable Sloping Ratios
Sloping protects workers by cutting back the trench walls at an angle inclined away from the excavation. The angle of repose depends directly on soil classification: Slope Ratio = Horizontal Run (H) Vertical Rise (V) \text{Slope Ratio} = \frac{\text{Horizontal Run (H)}}{\text{Vertical Rise (V)}} Slope Ratio = Vertical Rise (V) Horizontal Run (H)
Stable Rock: Vertical (90°)
Type A Soil: 3/4:1 (53°) — 0.75 ft horizontal for every 1 ft of vertical depth.
Type B Soil: 1:1 (45°) — 1.0 ft horizontal for every 1 ft of vertical depth.
Type C Soil: 11/2:1 (34°) — 1.5 ft horizontal for every 1 ft of vertical depth. SLOPING PROFILES BY SOIL TYPE:
- Type A Soil (3/4 : 1) Type B Soil (1 : 1) Type C Soil (1.5 : 1)
- ------------------- ------------------- ---------------------
- |/ |/ |/
- | 53° Angle | 45° Angle | 34° Angle
- | (3/4 H : 1 V) | (1 H : 1 V) | (1.5 H : 1 V)
- | | |
- +--------+ +-------------+ +-------------------+
- 2. Benching Rules
Benching cuts vertical or near-vertical steps into the trench wall.
Type A & Type B: Allowed. Maximum individual bench height is 4 feet .
Type C Soil: STRICTLY FORBIDDEN. Because granular cohesionless soils cannot support vertical shear planes, stepping/benching will trigger immediate collapse.
3. Trench Shields (Trench Boxes) & Shoring
Trench Shield Rating: Must be engineered, tab-rated by a registered professional engineer, and match the soil type and depth.
Shield Height Extension: If the top of the trench is sloped above a trench box, the top edge of the shield must extend at least 18 inches (0.45 m) above the vertical toe of the slope to prevent rolling rocks and debris from spilling inside.
Maximum Undercut: Plumbers may excavate no more than 2 feet (24 inches) below the bottom of a trench box, and only if the box is rated for the full depth and there is no evidence of soil boiling or loss behind the shield.
Safe Access, Egress, & Spoil Pile Setbacks
Plumbing codes and OSHA enforce exact dimensional requirements for getting into, working inside, and exiting trenches.
1. Access and Egress (Ladders, Ramps, & Stairways)
Depth Trigger: Required in all excavations 4 feet (1.22 m) or deeper .
25-Foot Lateral Travel Rule: Egress points must be located so that workers do not travel more than 25 feet of lateral distance to reach a ladder, stairway, or ramp (i.e., ladders spaced at least every 50 feet along the trench length).
3-Foot Ladder Extension Rule: The ladder side rails must extend at least 3 feet (36 inches) above the upper landing surface/grade and be securely tied off at the top to prevent slippage.
2. Spoil Pile & Equipment Setback
All excavated soil piles, pipe stock, tools, and heavy machinery must be kept at least 2 feet (24 inches) back from the edge of the excavation.
Alternatively, effective retaining devices (such as toe boards or sheet piling) must be installed to stop loose materials from falling into the trench.
Atmospheric Hazards & Confined Space Monitoring
Excavations near sewer lines, fuel gas lines, landfills, or industrial plants present severe atmospheric risks. In any trench deeper than 4 feet where hazardous atmospheres could exist, atmospheric testing is mandatory prior to worker entry.
Atmospheric Parameter Acceptable Safe Range Hazard Condition & Action
Oxygen (O₂) 19.5% to 23.5% <19.5% = Oxygen Deficient (requires forced ventilation or supplied air); >23.5% = Oxygen Enriched (extreme fire/explosion risk)
Flammable Gas / Vapor <10% of LEL ≥ 10% of Lower Explosive Limit (LEL) requires immediate evacuation and ventilation
Hydrogen Sulfide (H₂S) <10 ppm Toxic sewer gas. Rotting egg odor (deadens olfactory nerves at high concentrations). Ceiling limit 20 ppm; lethal at high exposure
Carbon Monoxide (CO) <35 ppm Toxic by-product of internal combustion engines (pumps, generators near trench). PEL 50 ppm
- PPE & Lockout/Tagout (LOTO - 29 CFR 1910.147)
- Personal Protective Equipment (PPE)
Head Protection: ANSI Z89.1 Type I/II hard hats required at all times around overhead hazards and excavations.
Eye/Face Protection: ANSI Z87.1 safety glasses with side shields or face shields when cutting cast iron, soldering, or brazing.
Foot Protection: ASTM F2413 steel-toe or composite-toe boots with puncture-resistant soles.
Respirators: N95 or HEPA elastomeric respirators for crystalline silica exposure during masonry cutting or concrete core drilling.
Lockout/Tagout (LOTO) Six-Step Sequence
Before servicing or tie-in on pressurized water, high-pressure steam, fuel gas, or electrical plumbing systems (e.g., booster pumps, sewage ejectors), plumbers must follow the strict LOTO protocol:
Preparation: Identify all energy sources (electrical, mechanical, hydraulic, pneumatic, gravitational, pressurized fluid/gas).
Notification: Inform all affected personnel that a lockout is taking place.
Shutdown: Turn off equipment using established operating controls.
Isolation: Operate energy-isolating devices (disconnect switches, line valves, circuit breakers) to physically isolate power.
LOTO Application: Apply assigned lockout padlocks and standardized warning tags to each isolating device.
Zero-Energy Verification: Bleed remaining pressure, drain residual water/gas, ground electrical conductors, and test start buttons to confirm a verified zero energy state before beginning work.