Study guide
5.1 Trap Design, Sizing, & Prohibited Traps
Texas Journeyman Plumber Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Licensing Laws, Board Rules, & Safety
1.1 TSBPE Laws, Board Rules, & Scope of Practice 1.2 Responsible Master Plumber (RMP) Supervision & Permitting 1.3 Jobsite Safety, OSHA Standards, & Trenching 1.4 Enforcement, Disciplinary Action, & Penalties
2 Chapter 2: Exam Format, Adopted Codes, & Definitions
2.1 Exam Format, Scoring, & Testing Logistics 2.2 Adopted Plumbing Codes & Jurisdictional Authority 2.3 Code Definitions & Trade Terminology
3 Chapter 3: General Regulations & Piping Installation
3.1 Approved Piping Materials & Standards 3.2 Pipe Hangers, Supports, & Spacing 3.3 Structural Protection, Sleeving, & Penetrations 3.4 System Testing & Inspection Requirements
4 Chapter 4: Drainage Systems & Pipe Sizing
4.1 Drainage Fixture Units (DFU) & Fixture Drains 4.2 Building Drains, Sewers, & Minimum Slopes 4.3 Cleanouts: Sizing, Clearances, & Locations 4.4 Sumps, Sewage Ejectors, & Indirect Waste Systems 4.5 Storm Drainage Systems
5 Chapter 5: Traps & Trap Seal Protection
5.1 Trap Design, Sizing, & Prohibited Traps 5.2 Trap Seal Protection, Trap Arms, & Trap Primers
6 Chapter 6: Venting Methods & Design
6.1 Vent Sizing, Developed Length, & Terminations 6.2 Individual, Common, & Relief Vents 6.3 Wet Venting, Circuit Venting, & Combination Systems 6.4 Air Admittance Valves (AAV) & Island Fixture Vents
7 Chapter 7: Potable Water Supply & Distribution
7.1 Water Supply Fixture Units (WSFU) & Pipe Sizing 7.2 Water Pressure, PRVs, & Thermal Expansion 7.3 Cross-Connection Control & Backflow Devices 7.4 Water Service, Metering, & System Disinfection
8 Chapter 8: Water Heaters & Scald Prevention
8.1 Water Heater Types, Sizing, & Installation 8.2 Temperature & Pressure (T&P) Relief Valves & Discharge 8.3 Combustion Air, Venting, & Scald-Prevention Mixing Valves
9 Chapter 9: Fuel Gas Piping Systems
9.1 Fuel Gas Properties & Piping Materials (IFGC / NFPA 54) 9.2 Gas Pipe Sizing & Longest Length Method 9.3 Gas Shutoff Valves, Regulators, & Pressure Testing
10 Chapter 10: Fixtures, Faucets, & Accessibility
10.1 Fixture Clearances & Accessibility Standards (ADA) 10.2 Water Conservation & Flush Rates 10.3 Urinals, Special Fixtures, & Interceptors 10.4 Fixture Fittings, Faucets, & Accessories
11 Chapter 11: Plumbing Math & Trade Calculations
11.1 45-Degree & Rolling Offset Calculations 11.2 Grade, Fall, & Invert Elevation Calculations 11.3 Volume, Capacity, & Hydrostatic Pressure Calculations
12 Chapter 12: Isometric Drawings & TSBPE Practical Exam
12.1 Isometric Drawing Principles & Piping Schematics 12.2 TSBPE 2-Story DWV Dollhouse Design & Layout 12.3 Water & Gas Piping Schematics for Practical Stations 12.4 Hands-On Shop Skills: Brazing, Soldering, & Flaring
5.1 Trap Design, Sizing, & Prohibited Traps
Key Takeaways Explain This Topic AI
Every fixture must be separately trapped by an approved water-seal trap placed as close as possible to the fixture outlet.
The vertical distance from the fixture outlet to the trap weir may not exceed 24 inches.
A trap seal must be not less than 2 inches and not more than 4 inches deep except for traps of special design.
A trap may not be larger than the fixture drain it connects to, and the required trap size is set by the fixture type.
S-traps, bell traps, drum traps, crown-vented traps, traps with moving parts, and traps with interior partitions are prohibited.
Last updated: August 2026
5.1 Trap Design, Sizing, & Prohibited Traps
Core Principle: The TSBPE examination review course devotes a full study chapter to traps, listing four subjects: the design of different types of traps, fixture traps, protection of trap seals, and prohibited traps . Board Rule 363.5(g)(1)(G) reinforces it, requiring an hour of classroom time on "design and prohibited traps; sizing and installation of traps and trap arms; and trap protection." A trap is a two-dollar fitting holding back the entire sanitary sewer — and it is the last barrier between a building's occupants and methane, hydrogen sulfide, and pathogens.
- 1. How a Water-Seal Trap Works FIXTURE OUTLET
- |
- | <-- Tailpiece. Vertical distance from the fixture
| outlet to the TRAP WEIR: 24 INCHES MAXIMUM.
- |
- +----+----+ <-- CROWN
- | |
- TRAP WEIR >---. | TRAP SEAL = vertical depth between the
| \ | crown weir and the top of the dip.
- | \___| MINIMUM 2 IN / MAXIMUM 4 IN
- | TRAP DIP
- +---------+
- |
- TRAP ARM ------> to the vent connection and the drain
The seal is nothing more than the water left standing between the dip and the weir after the fixture drains. Every rule in this chapter exists to make sure that water is deep enough to resist pressure, shallow enough to be pushed out and replaced on the next use, and shaped so the trap scours itself clean.
A properly installed trap must:
- pass water freely with no restriction;
- be self-cleaning (self-scouring) , so solids do not settle in the dip;
- hold a seal of not less than 2 inches and not more than 4 inches (traps of special design excepted);
- have no interior partitions and no moving or mechanical parts to maintain the seal;
be accessible for cleaning , and set true to its seal and level in both directions.
That list is the answer to one of the Board's own published sample questions: the characteristic that is not a requirement of a properly installed trap is that it has mechanical or moving parts.
2. One Trap per Fixture — and the Three Exceptions
The general rule: each plumbing fixture shall be separately trapped by an approved water-seal trap , placed as close as possible to the fixture outlet . Two traps in series on one fixture drain (a "double trap") is prohibited, because the air locked between them stops flow.
Exception Conditions
Integral trap Fixtures with traps integral to the fixture — water closets, most bidets, siphon-jet urinals — need no separate trap
Combination fixture A combination sink and laundry tray, or a multi-compartment sink, may use one trap where the compartments are adjacent , waste outlets are not more than 30 inches apart , and no compartment is more than 6 inches deeper than the adjoining compartment
Up to three single-compartment fixtures Up to three single-compartment sinks or lavatories in the same room may connect to one trap where the waste outlets are not more than 30 inches apart and the trap is centrally located
A food waste grinder or a dishwasher may discharge into a wye branch on the tailpiece of a kitchen sink ahead of that sink's trap; it does not get its own trap in residential work.
3. Required Trap Sizes
A trap is sized to the fixture, and a trap shall not be larger than the fixture drain to which it is connected . Oversizing is a real violation, not a harmless margin: an oversized trap loses velocity, stops scouring, and silts up.
- Fixture Minimum trap size DFU (private / IPC)
- Lavatory 1-1/4 in 1
- Drinking fountain 1-1/4 in 0.5
- Bathtub (with or without shower) 1-1/2 in 2
- Kitchen sink (with or without disposer/dishwasher) 1-1/2 in 2
- Laundry tub / bar sink 1-1/2 in 2 / 1
- Shower (single head) 2 in 2
- Clothes washer standpipe 2 in 2
- Floor drain 2 in 2
- Service (mop) sink 2 in or 3 in 2–3
- Water closet Integral (3-in drain) 3 (1.6 gpf)
- 4. Prohibited Traps
The code lists prohibited designs explicitly. Learn the list and the reason for each — exam items usually ask why .
Prohibited trap Why it is prohibited
"S" trap / full S trap The outlet turns vertically downward, so a falling column of water siphons the seal out on every use
Bell trap A loose bell cover is easily removed or lost, and the shallow annular seal evaporates and clogs
Drum trap Not self-scouring — the large barrel slows velocity, sludge settles, and the cleanout cover is usually buried
- Crown-vented trap A vent taken off the crown fills with grease and hair splash and chokes shut
- Traps with moving parts The seal depends on a flapper, ball, or spring that can stick, wear, or corrode open
Traps with interior partitions A corroded or cracked partition silently destroys the seal; only traps with an approved ground or molded seat are allowed
Building (house) trap A running trap on the building drain double-traps every fixture and blocks system air; permitted only where the AHJ specifically requires it, and then with a relieving vent and cleanout
Note
The S-trap trap. Retrofits under old lavatories are the most common S-trap violation in the field. If the trap arm turns down before it reaches a vent, you have built an S-trap even if you used a P-trap fitting. The cure is a properly located vent, an approved air admittance valve where permitted, or re-routing the arm — never a deeper trap.
5. Materials, Joints, and Accessibility
Approved trap materials include cast iron, copper alloy, and plastic meeting the referenced standards; tubular plastic waste fittings conform to ASTM F409 and metallic waste fittings to ASME A112.18.2 .
Slip joints are permitted only on the trap inlet, the trap outlet, and within the trap seal — never buried in a wall or under a slab on a concealed drain line.
Concealed slip joints require an access panel or utility space at least as large as the fitting, arranged so the trap can be removed.
Traps must be protected from freezing . A trap in an unheated crawl space, an exterior wall, or an unconditioned garage needs insulation, heat, or relocation.
Grease, oil, sand, and lint interceptors are traps in the code's sense and follow their own sizing and maintenance rules (see Chapter 10).