Study guide
8.2 Temperature & Pressure (T&P) Relief Valves & Discharge
Texas Journeyman Plumber Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Licensing Laws, Board Rules, & Safety
1.1 TSBPE Laws, Board Rules, & Scope of Practice 1.2 Responsible Master Plumber (RMP) Supervision & Permitting 1.3 Jobsite Safety, OSHA Standards, & Trenching 1.4 Enforcement, Disciplinary Action, & Penalties
2 Chapter 2: Exam Format, Adopted Codes, & Definitions
2.1 Exam Format, Scoring, & Testing Logistics 2.2 Adopted Plumbing Codes & Jurisdictional Authority 2.3 Code Definitions & Trade Terminology
3 Chapter 3: General Regulations & Piping Installation
3.1 Approved Piping Materials & Standards 3.2 Pipe Hangers, Supports, & Spacing 3.3 Structural Protection, Sleeving, & Penetrations 3.4 System Testing & Inspection Requirements
4 Chapter 4: Drainage Systems & Pipe Sizing
4.1 Drainage Fixture Units (DFU) & Fixture Drains 4.2 Building Drains, Sewers, & Minimum Slopes 4.3 Cleanouts: Sizing, Clearances, & Locations 4.4 Sumps, Sewage Ejectors, & Indirect Waste Systems 4.5 Storm Drainage Systems
5 Chapter 5: Traps & Trap Seal Protection
5.1 Trap Design, Sizing, & Prohibited Traps 5.2 Trap Seal Protection, Trap Arms, & Trap Primers
6 Chapter 6: Venting Methods & Design
6.1 Vent Sizing, Developed Length, & Terminations 6.2 Individual, Common, & Relief Vents 6.3 Wet Venting, Circuit Venting, & Combination Systems 6.4 Air Admittance Valves (AAV) & Island Fixture Vents
7 Chapter 7: Potable Water Supply & Distribution
7.1 Water Supply Fixture Units (WSFU) & Pipe Sizing 7.2 Water Pressure, PRVs, & Thermal Expansion 7.3 Cross-Connection Control & Backflow Devices 7.4 Water Service, Metering, & System Disinfection
8 Chapter 8: Water Heaters & Scald Prevention
8.1 Water Heater Types, Sizing, & Installation 8.2 Temperature & Pressure (T&P) Relief Valves & Discharge 8.3 Combustion Air, Venting, & Scald-Prevention Mixing Valves
9 Chapter 9: Fuel Gas Piping Systems
9.1 Fuel Gas Properties & Piping Materials (IFGC / NFPA 54) 9.2 Gas Pipe Sizing & Longest Length Method 9.3 Gas Shutoff Valves, Regulators, & Pressure Testing
10 Chapter 10: Fixtures, Faucets, & Accessibility
10.1 Fixture Clearances & Accessibility Standards (ADA) 10.2 Water Conservation & Flush Rates 10.3 Urinals, Special Fixtures, & Interceptors 10.4 Fixture Fittings, Faucets, & Accessories
11 Chapter 11: Plumbing Math & Trade Calculations
11.1 45-Degree & Rolling Offset Calculations 11.2 Grade, Fall, & Invert Elevation Calculations 11.3 Volume, Capacity, & Hydrostatic Pressure Calculations
12 Chapter 12: Isometric Drawings & TSBPE Practical Exam
12.1 Isometric Drawing Principles & Piping Schematics 12.2 TSBPE 2-Story DWV Dollhouse Design & Layout 12.3 Water & Gas Piping Schematics for Practical Stations 12.4 Hands-On Shop Skills: Brazing, Soldering, & Flaring
8.2 Temperature & Pressure (T&P) Relief Valves & Discharge
Key Takeaways Explain This Topic AI
Every storage water heater and hot water supply system must be equipped with an ASME/ANSI Z21.22 rated Temperature and Pressure (T&P) relief valve set to open at a maximum pressure of 150 psi and a maximum temperature of 210°F (99°C).
The T&P relief valve temperature-sensing probe must be installed in the top 6 inches of the tank where water reaches its highest thermal stratification zone.
The valve's steam relief rating (BTU/hr) must equal or exceed the maximum heat input rating of the water heater to prevent explosive steam vessel failure (BLEVE).
T&P discharge piping must be full nominal diameter of the valve outlet (minimum 3/4"), constructed of approved hot-water rated materials (copper, CPVC, galvanized steel; standard PVC and unrated PEX prohibited), and pitched continuously downward with no traps or dips.
The discharge pipe must terminate through an air gap 6 to 24 inches above the floor or ground (6 to 12 inches under UPC), have an unthreaded smooth terminus (no caps or hose threads permitted), and have zero shutoff valves, check valves, or tee fittings anywhere in the line.
Last updated: August 2026
8.2 Temperature & Pressure (T&P) Relief Valves & Discharge
Water heaters operate as closed pressure vessels subjected to continuous thermal cycling. If control thermostats fail in an "on" runaway condition, water inside the vessel can become superheated. The Temperature & Pressure (T&P) relief valve is the primary mechanical life-safety device protecting building occupants from catastrophic boiler and tank explosions.
On the Texas Journeyman Plumber examination, questions regarding T&P valve ratings, probe immersion depth, approved discharge materials, slope geometry, and prohibited terminal fittings appear with high frequency. Mastery of these exact code requirements is critical.
1. Thermodynamics & The BLEVE Hazard
To understand why T&P relief rules are so stringent, a plumber must grasp the physical behavior of superheated water . +-----------------------------------------------------------------------------------+
- | SUPERHEATED WATER & THE BLEVE PHENOMENON |
- | |
- | - AT ATMOSPHERIC PRESSURE (0 psi gauge / 14.7 psi absolute): |
- | Water boils at 212°F (100°C) and converts to steam. |
- | |
- | - UNDER CITY WATER PRESSURE (50 psi gauge / 64.7 psi absolute): |
- | Water does NOT boil at 212°F; its boiling point rises to 298°F (148°C). |
- | |
- | - THE HAZARD (BLEVE): |
- | If a 50-gallon tank at 300°F ruptures, the superheated liquid instantly flashes|
- | into steam, expanding 1,700 TIMES its liquid volume. |
- | Energy released = Equivalent to several sticks of dynamite. |
- +-----------------------------------------------------------------------------------+
A Boiling Liquid Expanding Vapor Explosion (BLEVE) occurs when a pressurized vessel containing liquid above its atmospheric boiling point ruptures. The sudden pressure drop causes the entire mass of water to flash instantly into steam, tearing the building structure apart. The T&P valve prevents this by releasing water before temperature reaches 212°F and before pressure exceeds tank design limits.
2. T&P Relief Valve Standards & Set Points
All safety relief valves installed on domestic water heaters must conform to ANSI Z21.22 / CSA 4.4 ( Relief Valves for Hot Water Supply Systems ) and bear the ASME Boiler and Pressure Vessel Code certification stamp. +-----------------------------------------------------------------------------------+
- | T&P RELIEF VALVE DUAL SET POINTS |
- | |
- | 1. PRESSURE SET POINT: 150 psi (1,034 kPa) MAXIMUM |
- | (Or the certified working pressure of the tank, whichever is lower) |
- | |
- | 2. TEMPERATURE SET POINT: 210°F (99°C) MAXIMUM |
- | (Opens prior to water reaching atmospheric boiling point of 212°F) |
- | |
- | 3. STEAM RELIEF CAPACITY: Must EQUAL OR EXCEED Water Heater BTU/hr Input |
- +-----------------------------------------------------------------------------------+
- Valve Sizing & BTU Rating Rule
The temperature-actuated steam relief rating (expressed in BTU/hr) listed on the T&P valve's metal data plate must be equal to or greater than the maximum burner or element input rating of the water heater. For example, a commercial gas water heater with an input of 199,000 BTU/hr requires a T&P valve rated for at least 199,000 BTU/hr steam relief discharge.
Sensing Element Placement (Top 6-Inch Rule)
Because hot water naturally rises due to lower density (thermal stratification), the hottest water in any storage tank resides in the upper 6 inches.
Code Rule: The temperature-sensing element of the T&P valve must be submerged within the top 6 inches (152 mm) of the water tank.
Acceptable Tappings: The valve may be threaded directly into the factory-provided female tapping in the top head or upper side shell of the tank, or installed in the hot water outlet piping within 6 inches of the tank head with the sensing probe extending into the tank.
Loading diagram... T&P Relief Valve Placement and Discharge Geometry
3. T&P Discharge Piping Mandates & Geometry
When a T&P valve opens, it discharges high-velocity scalding water and pressurized steam. Plumbing codes enforce stringent piping specifications to ensure this discharge cannot rupture pipes, trap scalding water, or injure building occupants.
Code Mandates for T&P Discharge Piping
Specification Category Code Mandate (IPC & UPC) Engineering Rationale
Nominal Pipe Diameter Full nominal size of valve outlet (minimum 3/4-inch bore) Any reduction in pipe size causes severe backpressure, choking steam relief.
Approved Piping Materials Copper (Type K, L, M), CPVC (ASTM D2846), Galvanized Steel, Malleable Iron, Stainless Steel, PEX (specifically listed for T&P discharge) Must withstand 210°F (99°C) water and steam under pressure without deformation.
Prohibited Materials Standard Schedule 40 PVC (ASTM D1785), Non-Rated PEX, Polyethylene Standard PVC softens and deflects at 140°F, rupturing violently under 210°F steam.
Pipe Slope & Pitch Continuous downward pitch toward discharge outlet Allows complete gravity drainage; prevents standing water accumulation.
Traps & Low Spots STRICTLY PROHIBITED (No dips, sags, loops, or trapped sections) Trapped water corrodes valve seat, accumulates sediment, and freezes in cold weather.
Valves & Tees STRICTLY PROHIBITED (Zero shutoff valves, check valves, or tees anywhere) Eliminates any possibility of the safety discharge path being blocked or restricted.
Manifolding Each T&P valve must discharge through an independent, dedicated pipe Prevents one water heater from back-discharging into an adjoining appliance.
Termination Clearance IPC: not more than 6 inches above, and not less than two times the discharge pipe diameter above, the floor or the flood level rim of the waste receptor. UPC: where discharged outside the building, not more than 2 feet and not less than 6 inches above the ground, pointing downward. Keeps a visible air gap while limiting the drop that scalding water can splash from.
Discharge Location Indirect waste receptor, floor drain with air gap, or building exterior Discharges visibly into a safe location where scalding cannot contact people.
Terminal Pipe End Plain, smooth end with NO THREADS Prevents individuals from threading caps, plugs, or garden hoses onto the line.
4. Critical Exam Traps & Common Field Violations
Plumbing inspectors and licensing examiners frequently test on subtle field errors that compromise T&P safety systems: +-----------------------------------------------------------------------------------+
- | MAJOR T&P CODE VIOLATIONS & INSPECTION FAILURES |
- | |
- | [VIOLATION 1: THREADED OUTLET TERMINUS] |
- | Leaving a threaded male adapter or threaded pipe nipple at the end of the line. |
- | - Why it fails: Occupants might screw on a cap to stop a slow leak. |
- | |
- | [VIOLATION 2: DISCHARGING INTO DRAIN PAN] |
- | Piping the T&P line to discharge into the 1.5" water heater drain pan. |
- | - Why it fails: Pan and 3/4" gravity pan drain cannot handle full-pressure |
- | 150 psi / 210°F blow-off; scalding water overflows into living space. |
- | |
- | [VIOLATION 3: USING SCHEDULE 40 PVC] |
- | Installing standard white PVC pipe for T&P discharge. |
- | - Why it fails: PVC heat deflection rating is only 140°F; steam melts the pipe. |
- | |
- | [VIOLATION 4: TRAPPED LINE / UPWARD RISE] |
- | Running discharge piping up and over an obstacle before dropping down. |
- | - Why it fails: Water remains trapped against the valve spring, causing mineral |
- | scaling that solders the valve disc shut. |
- +-----------------------------------------------------------------------------------+
- Thermal Expansion vs. T&P Discharge
When a backflow preventer, check valve, or pressure reducing valve (PRV) is installed on the cold water supply, a closed plumbing system is created. As water heats, it expands. Without a properly charged diaphragm thermal expansion tank , static water pressure will spike to 150 psi during every heating cycle, causing the T&P relief valve to weep continuously.
Plumber's Diagnostic: Weeping cold or warm water at 150 psi indicates a thermal expansion failure; blasting 210°F steam indicates a runaway thermostat failure.