Study guide
8.1 AC Waveform Generation & Key Values
City & Guilds 2365 Level 2 Diploma in Electrical Installations Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Qualification Overview
1.1 About the City & Guilds 2365 Level 2 Qualification 1.2 Study Strategy, Exam Technique & Resource Navigation
2 Health, Safety & Environmental Legislation, Risk Assessment & Permits
2.1 Statutory Framework & Health and Safety Law 2.2 Hazardous Substances, Incident Reporting & Welfare 2.3 Work Equipment, Manual Handling & PPE 2.4 Environmental Legislation, Pollution & Site Waste 2.5 Risk Assessments, Method Statements, Permits to Work & Safety Signs
3 Electrical Safety, Safe Isolation, Site Hazards & Emergencies
3.1 Safe Isolation Procedures & GS38 Compliance 3.2 Electrical Hazards & Electric Shock Physiology 3.3 Fire Safety, Site Supplies & Emergency Response 3.4 Accidents, First Aid, Emergency Procedures & Reporting
4 Working at Height & Access Equipment
4.1 Work at Height Regulations & Risk Management 4.2 Ladders, Stepladders & Podiums 4.3 Mobile Access Towers & Scaffolding Systems
5 Mathematical Principles, Units & Basic Mechanics
5.1 Mathematical Foundations & Transposition for Electricians 5.2 SI Units of Measurement in Electrotechnology 5.3 Basic Mechanics: Force, Work, Power & Mechanical Energy 5.4 Mass, Weight, Levers, Gears & Pulleys
6 Electron Theory, Resistance, Resistivity & DC Circuits
6.1 Resistance, Resistivity & Conductor Dimensions 6.2 Temperature Coefficient of Resistance 6.3 Ohm's Law, Power & Direct Current Calculations 6.4 Series, Parallel & Combination DC Circuits 6.5 Electron Theory, Conductors, Insulators & the Effects of Current
7 Magnetism, Electromagnetism & Transformers
7.1 Magnetic Fields, Flux & Solenoid Properties 7.2 Electromagnetic Induction & Motor/Generator Principles 7.3 Transformer Principles, Construction & Calculations
8 Alternating Current, Three-Phase Systems & Electronic Components
8.1 AC Waveform Generation & Key Values 8.2 AC Circuit Theory: Reactance, Impedance & Power Factor 8.3 Three-Phase Generation, Star-Delta & UK Distribution 8.4 Electronic Components in Electrical Systems
9 Industry Regulations, Technical Information & Drawings
9.1 Electrical Regulations, Standards & Part P 9.2 Electrical Drawings, Diagrams & BS EN 60617 Symbols 9.3 Technical Specifications, Schedules & Environmental Influences
10 Wiring Systems, Cables, Containment & Practical Installation
10.1 Thermoplastic, Armoured & Flexible Cables 10.2 Specialised Cables: MICC & Fire-Performance Cables 10.3 Conduit Systems: Steel & PVC 10.4 Trunking, Cable Tray & Cable Supports 10.5 Unit 204 Practical Skills: Tools, Preparation & Installing Wiring Systems
11 Final Circuits, Protective Devices, Alarm & Control Circuits
11.1 Lighting Circuits & Switching Arrangements 11.2 Power Circuits: Ring Final, Radial & Dedicated Circuits 11.3 Consumer Units, Distribution Boards & Protective Devices 11.4 Alarm, Emergency Lighting, Data & Control Circuits
12 Cable Selection & Structural Installation
12.1 Cable Current-Carrying Capacity & Correction Factors 12.2 Voltage Drop Principles & Calculations 12.3 Structural Integrity & Concealed Cable Routing
13 Supply Systems, Earthing, Shock Protection & Micro-Renewables
13.1 UK Electricity Supply Networks & Distribution 13.2 Earthing System Configurations: TN-S, TN-C-S (PME and PNB) & TT 13.3 Protective Conductors, Bonding & Earth Electrodes 13.4 Automatic Disconnection of Supply (ADS) & Maximum Zs 13.5 Micro-Renewable Energy Technologies
14 Electrical Inspection & Dead Testing Sequence
14.1 Inspection Principles & Testing Safety to GS38 14.2 Continuity Testing: Protective Conductors & Ring Circuits 14.3 Insulation Resistance & Polarity Verification
15 Live Testing, Certification & Handover
15.1 Live Testing: Earth Loop Impedance, PFC & RCD Testing 15.2 Certification, Handover & Commissioning
16 Communicating within Building Services Engineering (Unit 210)
16.1 The Construction Team: Site Management, Trades & Site Visitors 16.2 Information Sources: Legislation, Guidance & Workplace Documents 16.3 Customer Information, Company Policies & Limits of Authority 16.4 Communicating Effectively: Methods, Accessibility & Conflict
8.1 AC Waveform Generation & Key Values
Key Takeaways Explain This Topic AI
Alternating Current (AC) is generated when a conductive loop rotates at constant angular velocity ( ω = 2 π f \omega = 2\pi f ω = 2 π f ) through a uniform magnetic field, inducing a sinusoidal electromotive force e = E p k sin ( ω t ) e = E_{pk} \sin(\omega t) e = E p k sin ( ω t ) in accordance with Faraday's Law.
The UK standard mains electrical supply operates at a nominal frequency of 50 Hz, which equates to a periodic time of T = 1 / 50 = 0.02 s = 20 ms T = 1/50 = 0.02\text{ s} = 20\text{ ms} T = 1/50 = 0.02 s = 20 ms per complete 360 ∘ 360^\circ 36 0 ∘ electrical cycle.
The Root Mean Square (RMS) value represents the DC heating equivalent of an AC waveform; for a pure sine wave, V r m s = V p k / 2 ≈ 0.707 × V p k V_{rms} = V_{pk} / \sqrt{2} \approx 0.707 \times V_{pk} V r m s = V p k / 2 ≈ 0.707 × V p k , making nominal 230 V UK mains reach an instantaneous peak voltage of approximately 325 V (650 V peak-to-peak).
The average value over a single half-cycle is V a v g = ( 2 / π ) × V p k ≈ 0.637 × V p k V_{avg} = (2/\pi) \times V_{pk} \approx 0.637 \times V_{pk} V a vg = ( 2/ π ) × V p k ≈ 0.637 × V p k , yielding a sinusoidal Form Factor of V r m s / V a v g ≈ 1.11 V_{rms} / V_{avg} \approx 1.11 V r m s / V a vg ≈ 1.11 and a Peak (Crest) Factor of V p k / V r m s ≈ 1.414 V_{pk} / V_{rms} \approx 1.414 V p k / V r m s ≈ 1.414 .
Last updated: October 2026
AC Waveform Generation & Key Values
In direct current (DC) circuits, electric charge drifts continuously in a single direction under a steady potential difference. While direct current is essential for battery storage, electronic circuitry, and electric vehicles, modern public electrical distribution networks rely almost universally on Alternating Current (AC) . In an alternating system, the magnitude of the electromotive force (EMF) changes continuously with time, and its polarity reverses at regular, periodic intervals, causing the mobile electrons within the circuit conductors to oscillate back and forth about fixed mean positions.
Alternating current dominates global electrical infrastructure because alternating voltages can be stepped up efficiently using electromagnetic transformers for long-distance, high-voltage transmission with minimal I 2 R I^2R I 2 R copper losses, and subsequently stepped down to safe utilization voltages for domestic and commercial consumers. Understanding the mathematical generation and characteristic values of alternating waveforms is fundamental for City & Guilds 2365 Level 2 electrotechnical studies.
Generation of an Alternating EMF
The fundamental generation of an alternating voltage relies on electromagnetic induction , described by Faraday's Law of Induction : whenever a conductor moves relative to a magnetic field such that it cuts magnetic flux lines, an electromotive force is induced across the conductor terminals. The direction of this induced EMF is determined by Fleming's Right-Hand Rule (the Generator Rule):
Thumb : Direction of physical conductor motion.
First Finger : Direction of magnetic field lines (North to South).
Second Finger : Direction of induced conventional current / EMF.
The Simple Alternator Model
Consider a simple AC generator (alternator) consisting of a rectangular loop of copper wire rotating at a constant angular velocity ( ω \omega ω , measured in radians per second) around a central axis within a uniform magnetic field of flux density B B B (Tesla):
0 ∘ 0^\circ 0 ∘ Position (Vertical Plane) : When the coil sides move parallel to the magnetic flux lines, the rate of flux cutting is zero ( d Φ d t = 0 \frac{d\Phi}{dt} = 0 d t d Φ = 0 ). Consequently, the induced instantaneous EMF is zero ( e = 0 V e = 0\text{ V} e = 0 V ).
90 ∘ 90^\circ 9 0 ∘ Position (Horizontal Plane) : As the loop rotates into the horizontal plane, the conductor sides cut the magnetic flux lines at a perpendicular ( 90 ∘ 90^\circ 9 0 ∘ ) angle, achieving the maximum possible rate of flux cutting. The induced EMF reaches its positive maximum or peak value ( + E p k +E_{pk} + E p k ).
180 ∘ 180^\circ 18 0 ∘ Position (Vertical Plane) : The loop sides return to moving parallel to the magnetic field lines. The rate of flux cutting returns to zero, and the induced EMF falls back to zero ( e = 0 V e = 0\text{ V} e = 0 V ).
270 ∘ 270^\circ 27 0 ∘ Position (Horizontal Plane) : The loop sides again cut magnetic flux lines perpendicularly, but because the conductors are now moving in the opposite direction relative to the magnetic poles, the induced EMF reaches its negative maximum or negative peak ( − E p k -E_{pk} − E p k ).
360 ∘ 360^\circ 36 0 ∘ Position (Completion of Cycle) : The loop returns to its initial starting orientation, completing one full revolution ( 2 π 2\pi 2 π radians) and bringing the induced EMF back to zero.
Because the linear velocity vector perpendicular to the magnetic field varies with the sine of the angle of rotation ( θ = ω t \theta = \omega t θ = ω t ), the resulting voltage waveform is a pure sine wave . The instantaneous induced EMF ( e e e ) at any given elapsed time ( t t t ) is given by the formula:
e = E p k sin ( ω t ) = E p k sin ( 2 π f t ) e = E_{pk} \sin(\omega t) = E_{pk} \sin(2\pi f t) e = E p k sin ( ω t ) = E p k sin ( 2 π f t )
Where:
- e e e = Instantaneous EMF in volts ( V \text{V} V )
- E p k E_{pk} E p k = Maximum peak EMF in volts ( V \text{V} V )
ω \omega ω = Angular velocity in radians per second ( rad/s \text{rad/s} rad/s ), where ω = 2 π f \omega = 2\pi f ω = 2 π f
- f f f = Frequency in Hertz ( Hz \text{Hz} Hz )
- t t t = Elapsed time in seconds ( s \text{s} s )
- Sine Wave Terminology and Metrics
To analyze, measure, and calculate the effects of alternating current in electrotechnical installations, electricians must use precise technical terminology:
1. Cycle
A cycle is one complete sequence of positive and negative variations of an alternating quantity, encompassing a full 360 ∘ 360^\circ 36 0 ∘ ( 2 π 2\pi 2 π radians) of angular rotation. After completing one cycle, the waveform repeats identically.
2. Periodic Time ( T T T )
The periodic time (symbol T T T ) is the duration in seconds required for an alternating waveform to complete one full cycle. It is measured in seconds ( s \text{s} s ) or milliseconds ( ms \text{ms} ms , where 1 ms = 10 − 3 s 1\text{ ms} = 10^{-3}\text{ s} 1 ms = 1 0 − 3 s ).
3. Frequency ( f f f )
The frequency (symbol f f f ) is the number of complete cycles executed by the alternating waveform per second. The SI unit of frequency is the Hertz ( Hz \text{Hz} Hz ), where 1 Hz = 1 cycle per second 1\text{ Hz} = 1\text{ cycle per second} 1 Hz = 1 cycle per second .
Frequency and periodic time are reciprocal quantities:
f = 1 T , T = 1 f f = \frac{1}{T}, \qquad T = \frac{1}{f} f = T 1 , T = f 1
In the United Kingdom, statutory regulations (Electricity Safety, Quality and Continuity Regulations) mandate that the public electricity supply operates at a nominal frequency of 50 Hz 50\text{ Hz} 50 Hz (with an operational statutory tolerance of ± 1 % \pm 1\% ± 1% , or 49.5 Hz 49.5\text{ Hz} 49.5 Hz to 50.5 Hz 50.5\text{ Hz} 50.5 Hz ). For a standard UK 50 Hz 50\text{ Hz} 50 Hz supply, the periodic time of each cycle is:
T = 1 50 = 0.02 s = 20 ms T = \frac{1}{50} = 0.02\text{ s} = 20\text{ ms} T = 50 1 = 0.02 s = 20 ms
Note
In specialized aerospace and naval defence installations, electrical power systems frequently operate at 400 Hz 400\text{ Hz} 400 Hz . A higher frequency allows aircraft generators and transformers to use significantly smaller, lighter magnetic cores ( T = 1 / 400 = 2.5 ms T = 1/400 = 2.5\text{ ms} T = 1/400 = 2.5 ms ), achieving substantial weight savings.
4. Instantaneous Value ( v v v or i i i )
The instantaneous value represents the magnitude of voltage or current at one specific, designated instant in time or at a specific angular position along the waveform. Lowercase symbols ( v v v and i i i ) denote instantaneous values, distinguishing them from steady or effective values.
5. Peak Value ( V p k V_{pk} V p k or I p k I_{pk} I p k )
The peak value (also known as the maximum value, V m V_m V m or I m I_m I m , or amplitude) is the greatest instantaneous magnitude attained by the waveform during either the positive or negative half-cycle, measured from the zero reference axis.
6. Peak-to-Peak Value ( V p k − p k V_{pk-pk} V p k − p k or I p k − p k I_{pk-pk} I p k − p k )
The peak-to-peak value is the total voltage or current excursion between the positive maximum crest and the negative maximum trough. For a symmetrical sinusoidal waveform:
V p k − p k = 2 × V p k V_{pk-pk} = 2 \times V_{pk} V p k − p k = 2 × V p k
On an oscilloscope screen, technicians measure peak-to-peak voltage directly by counting vertical graticule divisions between top and bottom peaks.
7. Root Mean Square (RMS) Value ( V r m s V_{rms} V r m s or I r m s I_{rms} I r m s )
Because an alternating current continuously varies between zero, positive peak, zero, and negative peak, the peak value cannot describe the continuous working capacity of the supply. The Root Mean Square (RMS) value (often termed the effective value ) resolves this problem.
Formal Definition of RMS Value: The RMS value of an alternating current is that value of direct current which, when flowing through a given resistor for a given time, produces the exact same amount of heat energy (power dissipation) as the alternating current flowing through the same resistor for the same time.
Mathematically, for a pure symmetrical sinusoidal waveform, the RMS value is obtained by taking the square root of the mean of the squared instantaneous values over one cycle:
V r m s = V p k 2 ≈ 0.7071 × V p k V_{rms} = \frac{V_{pk}}{\sqrt{2}} \approx 0.7071 \times V_{pk} V r m s = 2 V p k ≈ 0.7071 × V p k
Conversely, if the RMS value is known, the peak voltage is calculated by multiplying by 2 \sqrt{2} 2 :
V p k = 2 × V r m s ≈ 1.4142 × V r m s V_{pk} = \sqrt{2} \times V_{rms} \approx 1.4142 \times V_{rms} V p k = 2 × V r m s ≈ 1.4142 × V r m s
In the United Kingdom the declared single-phase low-voltage supply is 230 V 230\text{ V} 230 V RMS . The Electricity Safety, Quality and Continuity Regulations (ESQCR) permit a tolerance of + 10 % / − 6 % +10\% / -6\% + 10%/ − 6% , giving a range of 216.2 V 216.2\text{ V} 216.2 V to 253.0 V 253.0\text{ V} 253.0 V . The peak voltage corresponding to nominal 230 V 230\text{ V} 230 V RMS is:
V p k = 230 V × 1.4142 ≈ 325.27 V ≈ 325 V V_{pk} = 230\text{ V} \times 1.4142 \approx 325.27\text{ V} \approx 325\text{ V} V p k = 230 V × 1.4142 ≈ 325.27 V ≈ 325 V
The corresponding peak-to-peak excursion is:
V p k − p k = 2 × 325.27 V ≈ 650.5 V V_{pk-pk} = 2 \times 325.27\text{ V} \approx 650.5\text{ V} V p k − p k = 2 × 325.27 V ≈ 650.5 V
Warning
Although electrical equipment is specified and labeled in terms of its RMS operating voltage (e.g., 230 V 230\text{ V} 230 V ), the electrical insulation on cables, terminal blocks, printed circuit boards, and surge protection devices (SPDs) must withstand the instantaneous peak voltage ( 325 V 325\text{ V} 325 V nominal, rising to about 358 V 358\text{ V} 358 V at the + 10 % +10\% + 10% limit). Exceeding this peak stress causes dielectric breakdown, tracking, and insulation failure.
8. Average Value ( V a v g V_{avg} V a vg or I a v g I_{avg} I a vg )
If the arithmetic average of a symmetrical sine wave is calculated over one complete 360 ∘ 360^\circ 36 0 ∘ cycle, the positive half-cycle and negative half-cycle cancel out completely, yielding an average value of zero ( 0 V 0\text{ V} 0 V ). Therefore, in electrotechnical engineering, the average value of an AC waveform is strictly defined as the arithmetic mean of all instantaneous values over one half-cycle ( 180 ∘ 180^\circ 18 0 ∘ or π \pi π radians):
V a v g = 2 π × V p k ≈ 0.6366 × V p k ≈ 0.637 × V p k V_{avg} = \frac{2}{\pi} \times V_{pk} \approx 0.6366 \times V_{pk} \approx 0.637 \times V_{pk} V a vg = π 2 × V p k ≈ 0.6366 × V p k ≈ 0.637 × V p k
Expressed in terms of the RMS value:
V a v g = 0.637 0.707 × V r m s ≈ 0.90 × V r m s V_{avg} = \frac{0.637}{0.707} \times V_{rms} \approx 0.90 \times V_{rms} V a vg = 0.707 0.637 × V r m s ≈ 0.90 × V r m s
The average value is particularly critical when designing and testing rectifier circuits, battery charging systems, and DC motor drives fed from AC supplies.
9. Form Factor and Peak (Crest) Factor
Two dimensionless mathematical ratios describe the shape and profile of an alternating waveform:
Form Factor : The ratio of the RMS value to the half-cycle average value: Form Factor = V r m s V a v g = 0.7071 × V p k 0.6366 × V p k = π 2 2 ≈ 1.11 \text{Form Factor} = \frac{V_{rms}}{V_{avg}} = \frac{0.7071 \times V_{pk}}{0.6366 \times V_{pk}} = \frac{\pi}{2\sqrt{2}} \approx 1.11 Form Factor = V a vg V r m s = 0.6366 × V p k 0.7071 × V p k = 2 2 π ≈ 1.11
Peak Factor (Crest Factor) : The ratio of the peak maximum value to the RMS value: Peak Factor = V p k V r m s = V p k 0.7071 × V p k = 2 ≈ 1.414 \text{Peak Factor} = \frac{V_{pk}}{V_{rms}} = \frac{V_{pk}}{0.7071 \times V_{pk}} = \sqrt{2} \approx 1.414 Peak Factor = V r m s V p k = 0.7071 × V p k V p k = 2 ≈ 1.414
AC Waveform Parameter Symbol Mathematical Derivation (Sine Wave) Multiplier from Peak ( V p k V_{pk} V p k ) Numerical Example ( 230 V 230\text{ V} 230 V RMS Mains)
Peak Value V p k V_{pk} V p k Given or 2 × V r m s \sqrt{2} \times V_{rms} 2 × V r m s 1.000 × V p k 1.000 \times V_{pk} 1.000 × V p k 325.3 V 325.3\text{ V} 325.3 V
Peak-to-Peak V p k − p k V_{pk-pk} V p k − p k 2 × V p k 2 \times V_{pk} 2 × V p k 2.000 × V p k 2.000 \times V_{pk} 2.000 × V p k 650.5 V 650.5\text{ V} 650.5 V
RMS (Effective) V r m s V_{rms} V r m s V p k / 2 V_{pk} / \sqrt{2} V p k / 2 0.707 × V p k 0.707 \times V_{pk} 0.707 × V p k 230.0 V 230.0\text{ V} 230.0 V
Average (Half-Cycle) V a v g V_{avg} V a vg ( 2 / π ) × V p k (2 / \pi) \times V_{pk} ( 2/ π ) × V p k 0.637 × V p k 0.637 \times V_{pk} 0.637 × V p k 207.0 V 207.0\text{ V} 207.0 V
Form Factor k f k_f k f V r m s / V a v g V_{rms} / V_{avg} V r m s / V a vg 1.11 1.11 1.11 (dimensionless) 1.11 1.11 1.11
Peak (Crest) Factor k p k_p k p V p k / V r m s V_{pk} / V_{rms} V p k / V r m s 1.414 1.414 1.414 (dimensionless) 1.414 1.414 1.414
Tip
Standard analogue meters and basic digital multimeters (DMMs) do not compute actual RMS values. Instead, they rectify the AC waveform, measure the average value, and internally multiply the reading by 1.11 1.11 1.11 (the sinusoidal form factor) to display an estimated RMS reading. If used on non-sinusoidal waveforms—such as phase-cut dimmer switches, LED drivers, or variable-frequency drive (VFD) inverter outputs—these average-responding meters can produce errors exceeding 30 % 30\% 30% . Electricians must use True RMS instruments when testing modern electronic installations.
- Step-by-Step Worked Calculations
- Worked Example 1: Periodic Time and Frequency Calculations
Problem: A high-frequency induction heating generator operates with a measured periodic time of 0.4 ms 0.4\text{ ms} 0.4 ms per cycle. Determine its operating frequency in kiloHertz ( kHz \text{kHz} kHz ). In addition, calculate the periodic time of a standard UK 50 Hz 50\text{ Hz} 50 Hz supply in milliseconds.
Solution:
Convert periodic time to base SI units (seconds): T = 0.4 ms = 0.4 × 10 − 3 s = 0.0004 s T = 0.4\text{ ms} = 0.4 \times 10^{-3}\text{ s} = 0.0004\text{ s} T = 0.4 ms = 0.4 × 1 0 − 3 s = 0.0004 s
Calculate frequency using f = 1 / T f = 1/T f = 1/ T : f = 1 0.0004 s = 2 , 500 Hz = 2.5 kHz f = \frac{1}{0.0004\text{ s}} = 2,500\text{ Hz} = 2.5\text{ kHz} f = 0.0004 s 1 = 2 , 500 Hz = 2.5 kHz
Calculate the periodic time of UK 50 Hz 50\text{ Hz} 50 Hz mains: T = 1 50 Hz = 0.02 s = 20 ms T = \frac{1}{50\text{ Hz}} = 0.02\text{ s} = 20\text{ ms} T = 50 Hz 1 = 0.02 s = 20 ms
Worked Example 2: Determining Waveform Values from Peak Voltage
Problem: An oscilloscope connected across an isolating transformer displays a pure sinusoidal voltage with a positive peak amplitude of 170 V 170\text{ V} 170 V . Calculate:
The peak-to-peak voltage ( V p k − p k V_{pk-pk} V p k − p k ).
The RMS voltage ( V r m s V_{rms} V r m s ).
The average voltage over one half-cycle ( V a v g V_{avg} V a vg ).
Solution:
Peak-to-peak voltage: V p k − p k = 2 × V p k = 2 × 170 V = 340 V V_{pk-pk} = 2 \times V_{pk} = 2 \times 170\text{ V} = 340\text{ V} V p k − p k = 2 × V p k = 2 × 170 V = 340 V
RMS voltage: V r m s = 0.7071 × V p k = 0.7071 × 170 V = 120.21 V ≈ 120 V V_{rms} = 0.7071 \times V_{pk} = 0.7071 \times 170\text{ V} = 120.21\text{ V} \approx 120\text{ V} V r m s = 0.7071 × V p k = 0.7071 × 170 V = 120.21 V ≈ 120 V
Average voltage: V a v g = 0.6366 × V p k = 0.6366 × 170 V = 108.22 V V_{avg} = 0.6366 \times V_{pk} = 0.6366 \times 170\text{ V} = 108.22\text{ V} V a vg = 0.6366 × V p k = 0.6366 × 170 V = 108.22 V
Worked Example 3: Calculating Instantaneous Voltage at a Given Angle
Problem: A 230 V 230\text{ V} 230 V RMS, 50 Hz 50\text{ Hz} 50 Hz sinusoidal supply energizes a circuit. Calculate the instantaneous voltage ( v v v ) at an angle of 30 ∘ 30^\circ 3 0 ∘ after the waveform crosses zero rising positively, and determine the time ( t t t ) elapsed at this point.
Solution:
Determine the peak voltage: V p k = 2 × 230 V = 1.4142 × 230 V = 325.27 V V_{pk} = \sqrt{2} \times 230\text{ V} = 1.4142 \times 230\text{ V} = 325.27\text{ V} V p k = 2 × 230 V = 1.4142 × 230 V = 325.27 V
Calculate instantaneous voltage using v = V p k sin θ v = V_{pk} \sin\theta v = V p k sin θ : v = 325.27 × sin ( 30 ∘ ) = 325.27 × 0.5000 = 162.64 V v = 325.27 \times \sin(30^\circ) = 325.27 \times 0.5000 = 162.64\text{ V} v = 325.27 × sin ( 3 0 ∘ ) = 325.27 × 0.5000 = 162.64 V
Calculate the elapsed time corresponding to 30 ∘ 30^\circ 3 0 ∘ of rotation in a 50 Hz 50\text{ Hz} 50 Hz system:
One full cycle ( 360 ∘ 360^\circ 36 0 ∘ ) requires T = 20 ms T = 20\text{ ms} T = 20 ms .
Fraction of cycle = 30 ∘ / 360 ∘ = 1 / 12 30^\circ / 360^\circ = 1/12 3 0 ∘ /36 0 ∘ = 1/12 . t = 20 ms 12 ≈ 1.67 ms t = \frac{20\text{ ms}}{12} \approx 1.67\text{ ms} t = 12 20 ms ≈ 1.67 ms