Study guide

16.2 Information Sources: Legislation, Guidance & Workplace Documents

City & Guilds 2365 Level 2 Diploma in Electrical Installations Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Qualification Overview

1.1 About the City & Guilds 2365 Level 2 Qualification 1.2 Study Strategy, Exam Technique & Resource Navigation

2 Health, Safety & Environmental Legislation, Risk Assessment & Permits

2.1 Statutory Framework & Health and Safety Law 2.2 Hazardous Substances, Incident Reporting & Welfare 2.3 Work Equipment, Manual Handling & PPE 2.4 Environmental Legislation, Pollution & Site Waste 2.5 Risk Assessments, Method Statements, Permits to Work & Safety Signs

3 Electrical Safety, Safe Isolation, Site Hazards & Emergencies

3.1 Safe Isolation Procedures & GS38 Compliance 3.2 Electrical Hazards & Electric Shock Physiology 3.3 Fire Safety, Site Supplies & Emergency Response 3.4 Accidents, First Aid, Emergency Procedures & Reporting

4 Working at Height & Access Equipment

4.1 Work at Height Regulations & Risk Management 4.2 Ladders, Stepladders & Podiums 4.3 Mobile Access Towers & Scaffolding Systems

5 Mathematical Principles, Units & Basic Mechanics

5.1 Mathematical Foundations & Transposition for Electricians 5.2 SI Units of Measurement in Electrotechnology 5.3 Basic Mechanics: Force, Work, Power & Mechanical Energy 5.4 Mass, Weight, Levers, Gears & Pulleys

6 Electron Theory, Resistance, Resistivity & DC Circuits

6.1 Resistance, Resistivity & Conductor Dimensions 6.2 Temperature Coefficient of Resistance 6.3 Ohm's Law, Power & Direct Current Calculations 6.4 Series, Parallel & Combination DC Circuits 6.5 Electron Theory, Conductors, Insulators & the Effects of Current

7 Magnetism, Electromagnetism & Transformers

7.1 Magnetic Fields, Flux & Solenoid Properties 7.2 Electromagnetic Induction & Motor/Generator Principles 7.3 Transformer Principles, Construction & Calculations

8 Alternating Current, Three-Phase Systems & Electronic Components

8.1 AC Waveform Generation & Key Values 8.2 AC Circuit Theory: Reactance, Impedance & Power Factor 8.3 Three-Phase Generation, Star-Delta & UK Distribution 8.4 Electronic Components in Electrical Systems

9 Industry Regulations, Technical Information & Drawings

9.1 Electrical Regulations, Standards & Part P 9.2 Electrical Drawings, Diagrams & BS EN 60617 Symbols 9.3 Technical Specifications, Schedules & Environmental Influences

10 Wiring Systems, Cables, Containment & Practical Installation

10.1 Thermoplastic, Armoured & Flexible Cables 10.2 Specialised Cables: MICC & Fire-Performance Cables 10.3 Conduit Systems: Steel & PVC 10.4 Trunking, Cable Tray & Cable Supports 10.5 Unit 204 Practical Skills: Tools, Preparation & Installing Wiring Systems

11 Final Circuits, Protective Devices, Alarm & Control Circuits

11.1 Lighting Circuits & Switching Arrangements 11.2 Power Circuits: Ring Final, Radial & Dedicated Circuits 11.3 Consumer Units, Distribution Boards & Protective Devices 11.4 Alarm, Emergency Lighting, Data & Control Circuits

12 Cable Selection & Structural Installation

12.1 Cable Current-Carrying Capacity & Correction Factors 12.2 Voltage Drop Principles & Calculations 12.3 Structural Integrity & Concealed Cable Routing

13 Supply Systems, Earthing, Shock Protection & Micro-Renewables

13.1 UK Electricity Supply Networks & Distribution 13.2 Earthing System Configurations: TN-S, TN-C-S (PME and PNB) & TT 13.3 Protective Conductors, Bonding & Earth Electrodes 13.4 Automatic Disconnection of Supply (ADS) & Maximum Zs 13.5 Micro-Renewable Energy Technologies

14 Electrical Inspection & Dead Testing Sequence

14.1 Inspection Principles & Testing Safety to GS38 14.2 Continuity Testing: Protective Conductors & Ring Circuits 14.3 Insulation Resistance & Polarity Verification

15 Live Testing, Certification & Handover

15.1 Live Testing: Earth Loop Impedance, PFC & RCD Testing 15.2 Certification, Handover & Commissioning

16 Communicating within Building Services Engineering (Unit 210)

16.1 The Construction Team: Site Management, Trades & Site Visitors 16.2 Information Sources: Legislation, Guidance & Workplace Documents 16.3 Customer Information, Company Policies & Limits of Authority 16.4 Communicating Effectively: Methods, Accessibility & Conflict

16.2 Information Sources: Legislation, Guidance & Workplace Documents

Key Takeaways Explain This Topic AI

Unit 210 legislation covers data protection (UK GDPR and the Data Protection Act 2018), equal opportunities (Equality Act 2010), health and safety and employment law.

The Equality Act 2010 protects nine characteristics: age, disability, gender reassignment, marriage and civil partnership, pregnancy and maternity, race, religion or belief, sex, and sexual orientation.

Manufacturer guidance comes as installation instructions, service and maintenance instructions, and user instructions for the customer.

Delivery notes are checked against the order and the goods before signing, and time sheets record the hours worked on each job for wages and charging.

Work programmes (bar or Gantt charts) show the order and timing of tasks so labour and deliveries can be planned.

Last updated: October 2026

16.2 Information Sources: Legislation, Guidance & Workplace Documents

Learning outcome 2 is the largest part of the Unit 210 test: 9 of the 20 questions (45%). It covers the legislation and guidance that apply to the industry, the information used in the workplace, the information given to customers, and company policies. This section covers the first two; Section 16.3 covers the rest.

Statutory Legislation

Area Main law What it means at work

Data protection UK GDPR and the Data Protection Act 2018 Personal information about customers and colleagues must be kept secure and used only for the purpose it was collected for. Never share customers' details, door or alarm codes, or key arrangements, and do not post photos of customers' homes without permission.

Equal opportunities Equality Act 2010 (the Disability Discrimination Act still applies in Northern Ireland) It is unlawful to discriminate against, harass or victimise people because of a protected characteristic, in recruitment, at work or when providing services.

Health and safety Health and Safety at Work etc. Act 1974 and the regulations made under it The duties of employers and employees covered in Unit 201.

Employment Employment Rights Act 1996, Working Time Regulations 1998 and National Minimum Wage Act 1998 A written statement of the main terms of employment from the first day; an average working week of no more than 48 hours unless you opt out; a 20-minute break if you work more than 6 hours; 11 hours' rest between working days; 5.6 weeks' paid holiday a year; and at least the national minimum wage (with a separate apprentice rate).

The nine protected characteristics (Equality Act 2010)

Age, disability, gender reassignment, marriage and civil partnership, pregnancy and maternity, race, religion or belief, sex, and sexual orientation.

Regulations, Standards, Codes of Practice and Manufacturer Guidance

Regulations are statutory instruments made under Acts of Parliament, such as the Electricity at Work Regulations 1989, the Building Regulations and the water fittings regulations. Breaking them is a criminal offence.

British Standards such as BS 7671 (wiring), BS 5839 (fire alarms) and BS 5266 (emergency lighting) are non-statutory, but following them is the accepted way to show that the law has been met.

Codes of practice give practical guidance. HSE Approved Codes of Practice have a special legal status, and industry codes such as the IET Guidance Notes explain how to meet the standards.

Manufacturer guidance comes in three forms, and BS 7671 requires equipment to be installed taking the manufacturer's instructions into account:

Type Purpose Who uses it

Installation instructions How to fix, connect and commission the product: fixings, cable sizes, clearances, torque settings The installer

Service and maintenance instructions Inspection and servicing intervals, procedures, spare parts and fault finding Maintenance staff and service engineers

User instructions How to operate the product safely and look after it The customer, handed over at completion

Loading diagram... Where Workplace Information Comes From

Information Used in the Workplace

Document Purpose Your responsibility

Job specification Describes the work to be done and the standards, materials and finishes required Install exactly what is specified; query anything unclear before starting

Plans and drawings Show layouts, routes, positions and details (Section 9.2) Work from the current revision and record any changes for the as-fitted drawings

Work programmes Bar (Gantt) charts showing the order, start dates and durations of tasks, so labour, deliveries and trades can be coordinated Keep to your planned dates and tell your supervisor early about delays

Delivery notes List the goods delivered by a supplier Check the goods against the delivery note and order for quantity and damage before signing, and note any shortages or damage on the note

Time sheets Record the hours worked, and on which job Complete them accurately: they are used for wages, for charging the client (especially daywork) and for costing jobs

Policy documents The company's health and safety policy (required in writing by employers with five or more employees), environmental policy and customer service policy Read and follow them; they set out how the company expects work to be done

Other everyday documents include job sheets (the tasks for the day), variation orders (written instructions for changes to the work), daywork sheets (records of extra work charged at hourly rates), requisitions and purchase orders (requests for materials), and the site diary .

Example: reading a simple work programme

  • Task Week 1 Week 2 Week 3 Week 4
  • First fix containment ■ ■
  • Cable installation ■ ■
  • Plastering (other trade) ■ ■
  • Second fix and testing ■

Here cable installation must finish during week 3 before plastering takes over, so a two-day delay to the cables would hold up the plasterers and everyone after them.

Keeping information up to date

Information is only useful if it is current. Before starting work, check that you have the latest revision of each drawing and specification (Section 9.2), because work done from a superseded drawing may have to be removed. Return or clearly mark out-of-date copies, record changes made on site so that the as-fitted drawings can be updated, and keep signed records such as toolbox talk registers, inspection reports and test results where your company requires them. Good document control protects the company if there is a later dispute about what was agreed or installed.

Tip

If a delivery is short or damaged, write it on the delivery note before you sign. A signed, unmarked note is evidence that everything arrived complete and in good condition.