Study guide

2.5 Risk Assessments, Method Statements, Permits to Work & Safety Signs

City & Guilds 2365 Level 2 Diploma in Electrical Installations Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Qualification Overview

1.1 About the City & Guilds 2365 Level 2 Qualification 1.2 Study Strategy, Exam Technique & Resource Navigation

2 Health, Safety & Environmental Legislation, Risk Assessment & Permits

2.1 Statutory Framework & Health and Safety Law 2.2 Hazardous Substances, Incident Reporting & Welfare 2.3 Work Equipment, Manual Handling & PPE 2.4 Environmental Legislation, Pollution & Site Waste 2.5 Risk Assessments, Method Statements, Permits to Work & Safety Signs

3 Electrical Safety, Safe Isolation, Site Hazards & Emergencies

3.1 Safe Isolation Procedures & GS38 Compliance 3.2 Electrical Hazards & Electric Shock Physiology 3.3 Fire Safety, Site Supplies & Emergency Response 3.4 Accidents, First Aid, Emergency Procedures & Reporting

4 Working at Height & Access Equipment

4.1 Work at Height Regulations & Risk Management 4.2 Ladders, Stepladders & Podiums 4.3 Mobile Access Towers & Scaffolding Systems

5 Mathematical Principles, Units & Basic Mechanics

5.1 Mathematical Foundations & Transposition for Electricians 5.2 SI Units of Measurement in Electrotechnology 5.3 Basic Mechanics: Force, Work, Power & Mechanical Energy 5.4 Mass, Weight, Levers, Gears & Pulleys

6 Electron Theory, Resistance, Resistivity & DC Circuits

6.1 Resistance, Resistivity & Conductor Dimensions 6.2 Temperature Coefficient of Resistance 6.3 Ohm's Law, Power & Direct Current Calculations 6.4 Series, Parallel & Combination DC Circuits 6.5 Electron Theory, Conductors, Insulators & the Effects of Current

7 Magnetism, Electromagnetism & Transformers

7.1 Magnetic Fields, Flux & Solenoid Properties 7.2 Electromagnetic Induction & Motor/Generator Principles 7.3 Transformer Principles, Construction & Calculations

8 Alternating Current, Three-Phase Systems & Electronic Components

8.1 AC Waveform Generation & Key Values 8.2 AC Circuit Theory: Reactance, Impedance & Power Factor 8.3 Three-Phase Generation, Star-Delta & UK Distribution 8.4 Electronic Components in Electrical Systems

9 Industry Regulations, Technical Information & Drawings

9.1 Electrical Regulations, Standards & Part P 9.2 Electrical Drawings, Diagrams & BS EN 60617 Symbols 9.3 Technical Specifications, Schedules & Environmental Influences

10 Wiring Systems, Cables, Containment & Practical Installation

10.1 Thermoplastic, Armoured & Flexible Cables 10.2 Specialised Cables: MICC & Fire-Performance Cables 10.3 Conduit Systems: Steel & PVC 10.4 Trunking, Cable Tray & Cable Supports 10.5 Unit 204 Practical Skills: Tools, Preparation & Installing Wiring Systems

11 Final Circuits, Protective Devices, Alarm & Control Circuits

11.1 Lighting Circuits & Switching Arrangements 11.2 Power Circuits: Ring Final, Radial & Dedicated Circuits 11.3 Consumer Units, Distribution Boards & Protective Devices 11.4 Alarm, Emergency Lighting, Data & Control Circuits

12 Cable Selection & Structural Installation

12.1 Cable Current-Carrying Capacity & Correction Factors 12.2 Voltage Drop Principles & Calculations 12.3 Structural Integrity & Concealed Cable Routing

13 Supply Systems, Earthing, Shock Protection & Micro-Renewables

13.1 UK Electricity Supply Networks & Distribution 13.2 Earthing System Configurations: TN-S, TN-C-S (PME and PNB) & TT 13.3 Protective Conductors, Bonding & Earth Electrodes 13.4 Automatic Disconnection of Supply (ADS) & Maximum Zs 13.5 Micro-Renewable Energy Technologies

14 Electrical Inspection & Dead Testing Sequence

14.1 Inspection Principles & Testing Safety to GS38 14.2 Continuity Testing: Protective Conductors & Ring Circuits 14.3 Insulation Resistance & Polarity Verification

15 Live Testing, Certification & Handover

15.1 Live Testing: Earth Loop Impedance, PFC & RCD Testing 15.2 Certification, Handover & Commissioning

16 Communicating within Building Services Engineering (Unit 210)

16.1 The Construction Team: Site Management, Trades & Site Visitors 16.2 Information Sources: Legislation, Guidance & Workplace Documents 16.3 Customer Information, Company Policies & Limits of Authority 16.4 Communicating Effectively: Methods, Accessibility & Conflict

2.5 Risk Assessments, Method Statements, Permits to Work & Safety Signs

Key Takeaways Explain This Topic AI

A hazard is anything with the potential to cause harm, and a risk combines the likelihood of that harm with how severe it would be.

The HSE's five steps are: identify the hazards, decide who might be harmed, evaluate the risks and decide on precautions, record significant findings (required with five or more employees), and review.

A method statement sets out the step-by-step safe system of work for a task; if site conditions differ from it, stop and tell your supervisor.

A permit to work is a formal written authorisation for specified high-risk work, issued by an authorised person for a stated scope and time and cancelled when the work ends.

Safety signs: prohibition (red circle with a bar), warning (yellow triangle), mandatory (blue circle), safe condition (green rectangle) and fire equipment (red rectangle).

Last updated: October 2026

2.5 Risk Assessments, Method Statements, Permits to Work & Safety Signs

Learning outcome 3 of Unit 201 (7 of the 25 test questions) is about establishing a safe working environment. Before any task starts you should understand how the risks were assessed, what the agreed safe method is, whether a permit is needed, and what the safety signs around you mean.

Hazard and Risk

Unit 201 learning outcome 4 asks you to define a hazard. Keep the two terms separate:

A hazard is anything with the potential to cause harm: a live conductor, a fragile roof, a trailing lead, a solvent, asbestos.

A risk is the likelihood that the hazard will actually cause harm, combined with how serious that harm would be.

Many companies score risk with a simple matrix:

Risk rating = Likelihood × Severity \text{Risk rating} = \text{Likelihood} \times \text{Severity} Risk rating = Likelihood × Severity

  • Score Likelihood Severity
  • 1 Very unlikely Minor injury, no time off
  • 2 Unlikely Injury needing first aid
  • 3 Possible Injury causing time off work
  • 4 Likely Major injury
  • 5 Very likely Fatality or permanent disability

A rating of 1 to 4 is usually treated as low, 5 to 12 as medium and 15 to 25 as high. For example, drilling into a wall where live cables may be concealed might score likelihood 3 × severity 5 = 15 (high). Using a cable detector, following the drawings, keeping to the prescribed zones and isolating the circuits nearby reduces the likelihood to 1, giving a residual rating of 5.

Situations that can constitute a hazard

The Unit 201 range lists the workplace situations you must be able to recognise. Each one has typical controls:

Situation Typical controls

Temporary electrical supplies 110 V centre-tapped-to-earth supplies, RCD protection, protected distribution units, regular inspection

Trailing leads and cables Route leads overhead or along walls, use cable protectors at crossings, keep leads short and tidy

  • Slippery or uneven surfaces Clean up spills, cover holes, good lighting, suitable footwear
  • Dust and fumes Dust extraction on tools, wet cutting, ventilation, suitable respiratory protection

Handling and transporting equipment or materials Manual handling assessment, trolleys and lifting aids, team lifts

  • Contaminants and irritants COSHH assessment, gloves, barrier creams and good washing facilities
  • Fire Hot work permits, safe storage of flammables, extinguishers, clear escape routes
  • Working at height Follow the work at height hierarchy (Chapter 4)

Hazardous malfunctions of equipment Pre-use checks, take faulty equipment out of use and label it, report defects

Improper use, maintenance and storage of tools and equipment Training, the right tool for the job, maintenance records, secure and dry storage

The Five Steps to Risk Assessment

The HSE's approach, used to meet Regulation 3 of the Management of Health and Safety at Work Regulations 1999, has five steps:

Identify the hazards.

Decide who might be harmed and how (operatives, other trades, occupants, visitors, the public).

Evaluate the risks and decide on precautions.

Record your significant findings , which is a legal requirement for employers with five or more employees .

Review the assessment and update it if necessary , for example after an accident, a near miss or a change of method.

Removing or reducing risk before relying on PPE

Unit 201 asks what should be done to remove or minimise risks before deciding that PPE is needed. Work down the hierarchy of control (Section 2.3):

  • Level Electrical example
  • Eliminate Isolate and work dead; prefabricate containment at ground level instead of working at height
  • Substitute Use 110 V or battery tools instead of 230 V; use a water-based product instead of a solvent
  • Engineering controls Dust extraction on chasers, machine guards, edge protection, barriers around open floors
  • Administrative controls Method statements, permits, signs, training, supervision, job rotation
  • PPE Only for the risk that remains: eye protection, gloves, hearing protection, hard hat
  • Method Statements

A method statement (often combined with the risk assessment as "RAMS") is the written safe system of work for a task. It typically sets out:

  • the scope and location of the work;
  • the sequence of operations, step by step;
  • the hazards and the controls taken from the risk assessment;
  • the isolation arrangements, plant, tools and access equipment;
  • the PPE required;
  • the competence, training and supervision needed;

emergency and first-aid arrangements, and who to contact.

Your level of responsibility: read it, ask questions and sign it at the briefing; follow it exactly; and if conditions on site are different (for example the circuit cannot be isolated, or you find suspect asbestos), stop and tell your supervisor . Never improvise a different method.

Permits to Work

A permit to work is a formal, written system for controlling high-risk work such as work on or near high-voltage equipment, work in confined spaces, hot work and some live work. A permit:

describes exactly what work is authorised, where, and on which equipment;

lists the hazards and the precautions that must be in place first, such as isolations, locks, gas testing or a fire watch;

is issued by an authorised (responsible) person and accepted, by signature, by the competent person doing the work;

is valid only for a stated period and must be handed back and cancelled when the work is complete or stopped.

Work must never stray outside what the permit allows.

Term Meaning

Responsible person Someone appointed by the employer to take charge of the work or the installation, for example to issue permits and control isolations

Competent person Someone with the training, technical knowledge and experience to do the task safely, or who is supervised by such a person (EAWR Regulation 16)

Loading diagram... Permit to Work Life Cycle

Safety Signs

The Health and Safety (Safety Signs and Signals) Regulations 1996 require employers to provide safety signs where a risk cannot be adequately controlled by other means. The signs use standard shapes and colours:

Type Shape and colour Meaning Examples

Prohibition Red circle with a red diagonal bar, black symbol on white You must not do this No smoking; no unauthorised access

Warning Yellow triangle with a black border and black symbol Danger or hazard ahead Danger of electric shock; overhead cables

Mandatory Blue circle with a white symbol You must do this Wear head protection; wear eye protection

Safe condition Green rectangle or square with a white symbol The safe way, or emergency information Fire exit; first aid; eyewash

Fire equipment Red rectangle or square with a white symbol Location of firefighting equipment Fire extinguisher; fire alarm call point

Signs work alongside guarding : barriers around excavations and floor openings, covers over holes, and hoardings that keep the public away from the work.

Selecting and Checking Tools and Portable Equipment

The Unit 201 range also lists selecting and checking the correct power tools, hand tools and portable electrical equipment. Before use, check that the tool is the right one for the job and in good condition, that portable equipment has been inspected (and carries any in-date label your company uses), that site tools run from 110 V or batteries, and that guards and attachments are fitted correctly. Sections 2.3 and 10.5 cover these checks in detail.

Tip

Learn the sign colours as a set: red means stop or fire equipment, yellow means warning, blue means you must, and green means safe.