Study guide
10.2 Specialised Cables: MICC & Fire-Performance Cables
City & Guilds 2365 Level 2 Diploma in Electrical Installations Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Qualification Overview
1.1 About the City & Guilds 2365 Level 2 Qualification 1.2 Study Strategy, Exam Technique & Resource Navigation
2 Health, Safety & Environmental Legislation, Risk Assessment & Permits
2.1 Statutory Framework & Health and Safety Law 2.2 Hazardous Substances, Incident Reporting & Welfare 2.3 Work Equipment, Manual Handling & PPE 2.4 Environmental Legislation, Pollution & Site Waste 2.5 Risk Assessments, Method Statements, Permits to Work & Safety Signs
3 Electrical Safety, Safe Isolation, Site Hazards & Emergencies
3.1 Safe Isolation Procedures & GS38 Compliance 3.2 Electrical Hazards & Electric Shock Physiology 3.3 Fire Safety, Site Supplies & Emergency Response 3.4 Accidents, First Aid, Emergency Procedures & Reporting
4 Working at Height & Access Equipment
4.1 Work at Height Regulations & Risk Management 4.2 Ladders, Stepladders & Podiums 4.3 Mobile Access Towers & Scaffolding Systems
5 Mathematical Principles, Units & Basic Mechanics
5.1 Mathematical Foundations & Transposition for Electricians 5.2 SI Units of Measurement in Electrotechnology 5.3 Basic Mechanics: Force, Work, Power & Mechanical Energy 5.4 Mass, Weight, Levers, Gears & Pulleys
6 Electron Theory, Resistance, Resistivity & DC Circuits
6.1 Resistance, Resistivity & Conductor Dimensions 6.2 Temperature Coefficient of Resistance 6.3 Ohm's Law, Power & Direct Current Calculations 6.4 Series, Parallel & Combination DC Circuits 6.5 Electron Theory, Conductors, Insulators & the Effects of Current
7 Magnetism, Electromagnetism & Transformers
7.1 Magnetic Fields, Flux & Solenoid Properties 7.2 Electromagnetic Induction & Motor/Generator Principles 7.3 Transformer Principles, Construction & Calculations
8 Alternating Current, Three-Phase Systems & Electronic Components
8.1 AC Waveform Generation & Key Values 8.2 AC Circuit Theory: Reactance, Impedance & Power Factor 8.3 Three-Phase Generation, Star-Delta & UK Distribution 8.4 Electronic Components in Electrical Systems
9 Industry Regulations, Technical Information & Drawings
9.1 Electrical Regulations, Standards & Part P 9.2 Electrical Drawings, Diagrams & BS EN 60617 Symbols 9.3 Technical Specifications, Schedules & Environmental Influences
10 Wiring Systems, Cables, Containment & Practical Installation
10.1 Thermoplastic, Armoured & Flexible Cables 10.2 Specialised Cables: MICC & Fire-Performance Cables 10.3 Conduit Systems: Steel & PVC 10.4 Trunking, Cable Tray & Cable Supports 10.5 Unit 204 Practical Skills: Tools, Preparation & Installing Wiring Systems
11 Final Circuits, Protective Devices, Alarm & Control Circuits
11.1 Lighting Circuits & Switching Arrangements 11.2 Power Circuits: Ring Final, Radial & Dedicated Circuits 11.3 Consumer Units, Distribution Boards & Protective Devices 11.4 Alarm, Emergency Lighting, Data & Control Circuits
12 Cable Selection & Structural Installation
12.1 Cable Current-Carrying Capacity & Correction Factors 12.2 Voltage Drop Principles & Calculations 12.3 Structural Integrity & Concealed Cable Routing
13 Supply Systems, Earthing, Shock Protection & Micro-Renewables
13.1 UK Electricity Supply Networks & Distribution 13.2 Earthing System Configurations: TN-S, TN-C-S (PME and PNB) & TT 13.3 Protective Conductors, Bonding & Earth Electrodes 13.4 Automatic Disconnection of Supply (ADS) & Maximum Zs 13.5 Micro-Renewable Energy Technologies
14 Electrical Inspection & Dead Testing Sequence
14.1 Inspection Principles & Testing Safety to GS38 14.2 Continuity Testing: Protective Conductors & Ring Circuits 14.3 Insulation Resistance & Polarity Verification
15 Live Testing, Certification & Handover
15.1 Live Testing: Earth Loop Impedance, PFC & RCD Testing 15.2 Certification, Handover & Commissioning
16 Communicating within Building Services Engineering (Unit 210)
16.1 The Construction Team: Site Management, Trades & Site Visitors 16.2 Information Sources: Legislation, Guidance & Workplace Documents 16.3 Customer Information, Company Policies & Limits of Authority 16.4 Communicating Effectively: Methods, Accessibility & Conflict
10.2 Specialised Cables: MICC & Fire-Performance Cables
Key Takeaways Explain This Topic AI
Mineral Insulated Metal Sheathed (MICC) cable (BS EN 60702) comprises solid plain copper conductors embedded within highly compressed magnesium oxide (MgO) powder insulation inside a seamless malleable copper sheath, capable of continuous operation during structural fires up to 1083°C.
Magnesium oxide insulation is exceptionally hygroscopic; exposure of unsealed cable ends to atmospheric moisture rapidly degrades insulation resistance toward 0 Ω, requiring immediate heat drying and hermetic sealing using a threaded brass pot, cold compound, and insulating sleeving disc.
Polymeric fire-resistant cables such as Prysmian FP200 Gold (BS 7629-1, a 'Standard' fire-resistant cable) combine solid copper conductors, a hard fire-resistant insulation (Insudite), an aluminium screen in contact with a tinned copper CPC, and a low smoke zero halogen (LSOH) sheath.
BS 5839 distinguishes between Standard fire-resisting cables (maintaining circuit integrity for 30 minutes under BS EN 50200) and Enhanced fire-resisting cables (maintaining circuit integrity for 120 minutes with mechanical shock and water spray) for phased-evacuation and complex premises.
BS 7671 Table 51 sets harmonised core colours (Brown L1, Black L2, Grey L3, Blue Neutral), and Regulation 514.14.1 mandates an indelible two-colour warning notice at distribution boards where older (Red/Black) and harmonised (Brown/Blue) wiring coexist.
Last updated: October 2026
10.2 Specialised Cables: MICC & Fire-Performance Cables
Life-safety systems—including automatic fire detection, emergency escape lighting, sprinkler booster pumps, and smoke evacuation extractors—must maintain circuit integrity during severe building fires. Standard thermoplastic (PVC) cables ignite and decompose rapidly at temperatures between 200°C and 300°C, releasing dense toxic fumes and causing catastrophic short circuits. To keep power and signalling available during a fire, fire-resistant wiring systems are specified by the relevant codes of practice, notably BS 5839-1 for fire detection and alarm systems and BS 5266-1 for emergency lighting.
Mineral Insulated Metal Sheathed (MICC / Pyro) Cable
Manufactured in the United Kingdom to BS EN 60702 , Mineral Insulated Metal Sheathed (MICC) cable—frequently referred to by the trade name Pyro —represents the most durable wiring system in electrotechnical engineering. ┌──────────────────────────────────────────────────────────┐
- │ Seamless Copper Outer Sheath │
- │ ┌────────────────────────────────────────────────────┐ │
- │ │ Compacted Magnesium Oxide (MgO) Powder │ │
- │ │ ┌──────────────┐ ┌──────────────┐ │ │
- │ │ │ Solid Copper │ │ Solid Copper │ │ │
- │ │ │Conductor (L) │ │Conductor (N) │ │ │
- │ │ └──────────────┘ └──────────────┘ │ │
- │ └────────────────────────────────────────────────────┘ │
- └──────────────────────────────────────────────────────────┘
- Construction and Physical Metallurgy
Conductors: High-conductivity solid plain annealed copper conductors (Class 1).
Insulation: Highly compressed, pure Magnesium Oxide (MgO) mineral powder. Magnesium oxide is an inorganic refractory ceramic with exceptional dielectric strength and high thermal conductivity.
Outer Sheath: A continuous, seamless, malleable copper tube drawn down tightly over the compressed powder. The copper sheath acts as an exceptionally low-resistance integral Circuit Protective Conductor (CPC).
Polymer Oversheath (Optional): An extruded outer polymer/LSF jacket applied over the bare copper sheath. Oversheaths are available in several colours: red is commonly used to identify fire alarm circuits, while white and other colours suit neat surface runs in decorated or historic buildings.
Exceptional Engineering Properties
Incombustibility and Extreme Temperature Withstand: Because it contains zero organic or plastic materials, MICC cannot ignite, sustain combustion, or propagate flame. Copper melts at 1083°C , while magnesium oxide melts at 2800°C . MICC can operate continuously at temperatures exceeding 250°C and maintain circuit integrity throughout full-scale structural building fires exceeding 1000°C.
Zero Smoke and Toxic Emission: Produces zero smoke, halogens, or toxic fumes, eliminating asphyxiation risks along escape corridors.
Mechanical Robustness: The cable is completely malleable and ductile. When struck by a hammer, crushed by falling masonry, or bent around tight radii, the copper conductors, compressed powder, and outer sheath deform proportionally without insulation rupture, preserving electrical isolation.
Imperviousness: The seamless copper sheath is 100% impermeable to liquid water, steam, hydrocarbons, industrial solvents, and compressed gases.
Electromagnetic Compatibility (EMC): The continuous solid copper sheath provides an absolute Faraday shield against radio frequency interference (RFI) and electromagnetic interference (EMI).
The Critical Vulnerability: Hygroscopic Nature of MgO
Despite its extraordinary physical strength, MICC cable possesses one critical vulnerability: magnesium oxide is intensely hygroscopic .
When a cable end is cut and left exposed to ambient air, the dry compressed powder greedily absorbs atmospheric moisture. Moisture travels rapidly along the cable core by capillary action. As water molecules penetrate the porous ceramic, the insulation resistance plummets from several hundred megohms (> 500 MΩ) down to zero ohms (0 Ω) , converting the mineral insulation into a conductive slurry that causes immediate phase-to-earth dead shorts.
Drying Out Moist Cable (The Sweating Procedure)
If moisture penetrates an unsealed MICC cable end, the installer must sweat out the moisture using an LPG blowtorch or gas flame:
Apply heat to the copper sheath starting approximately 150 mm to 300 mm back from the exposed cut end.
Maintain gentle, circular flame movement to heat the copper without melting the conductor copper or annealing it excessively.
Slowly advance the flame along the sheath toward the open cut end, driving vaporized moisture out into the air as a visible wisp of steam.
Allow the cable to cool slightly, and immediately apply a temporary seal or terminate with a permanent brass pot. Sweating Out Moisture from MICC Cable:
- [Solid Copper Sheath] ──► [Flame Applied 300 mm back] ──► [Advance Flame]
- ──► [Steam Driven Out Forward] ──► [Exposed Cut End]
- Step-by-Step MICC Termination Sequence
Terminating an MICC cable requires specialized trade tools and methodical craftsmanship to ensure a permanent, hermetic, moisture-proof seal:
Gland Assembly: Slide the brass compression gland nut, compression olive (compression ring), and gland body over the cable before stripping.
Ringing and Stripping: Adjust the cutting blade of an MICC ringing tool to score a neat, square line around the copper sheath circumference at the exact stripping depth. Using an MICC rotary stripper (or hand-held joist stripper), rotate the tool clockwise around the cable. The hardened blade peels the copper sheath away as a continuous coiled shaving, exposing the conductors and compacted powder.
De-powdering: Wipe the conductors clean with a dry rag. Scrape away approximately 2 mm of loose powder from inside the sheath rim to provide a clean seating shoulder for the seal.
Screwing on the Brass Pot: Push an internally threaded brass pot over the conductors. The leading edge of the pot features a tapered, self-tapping thread. Using a pot-wrench or screw-pot tool, rotate the pot clockwise with firm forward pressure. The pot cuts its own matching threads directly into the soft outer copper sheath until the sheath edge seats flush against the interior shoulder of the pot.
Injecting Cold Compound: Knead a two-part cold sealing compound (mastic or epoxy resin). Force the compound firmly into the open mouth of the brass pot from one side using a potting tool or thumbs. Packing from one side prevents trapping air pockets or moisture bubbles against the powder face.
Fitting the Insulating Sleeving Disc: Thread flexible silicone or neoprene insulating sleeves over each exposed copper conductor. Push the pre-formed insulating disc down over the conductors and seat it squarely into the rim of the brass pot.
Pot Crimping: Place a brass pot crimping tool over the assembly. Tighten the tool to compress and crimp the upper brass rim of the pot down over the perimeter of the insulating disc, permanently locking the compound and conductors in a hermetic mechanical seal.
Immediate Insulation Testing: Connect an insulation resistance tester set to 500 V DC or 1000 V DC between conductors, and between each conductor and the copper sheath. The reading must be verified immediately. A healthy seal typically yields an insulation resistance reading well above 100 MΩ . Any reading below 1.0 MΩ indicates trapped moisture or air, requiring the pot to be cut off and the seal remade.
Modern Polymeric Fire-Resistant Cables (BS 7629-1 / FP200 Gold)
While MICC provides the ultimate fire endurance, its specialized tooling and labor-intensive termination led to the development of lightweight, easily terminated polymeric fire-performance cables , the most widely recognized being Prysmian FP200 Gold (manufactured to BS 7629-1 ). ┌──────────────────────────────────────────────────────────┐
- │ Tough LSOH Thermoplastic Outer Sheath │
- │ ┌────────────────────────────────────────────────────┐ │
- │ │ Laminated Aluminium Screen Tape │ │
- │ │ ┌──────────────┐ ┌────────────┐ ┌──────────┐ │ │
- │ │ │Silicone Cores│ │ Drain Wire │ │ Silicone │ │ │
- │ │ │ (Phase Con.) │ │(Tinned Cu) │ │ (Neutral)│ │ │
- │ │ └──────────────┘ └────────────┘ └──────────┘ │ │
- │ └────────────────────────────────────────────────────┘ │
- └──────────────────────────────────────────────────────────┘
- Construction and Fire-Resisting Mechanism
Conductors: Solid plain annealed copper conductors (Class 1).
Insulation: A hard, damage-resistant fire-resistant insulation (Prysmian's Insudite , classified as type EI5) designed to keep the conductors separated and the circuit working for the rated time in a fire. Some other fire-resistant cables use silicone-based insulation that forms a protective ceramic layer when it burns.
Electrostatic Screen: An aluminium/polyester laminated metallic screening tape folded longitudinally over the insulated cores, providing 100% electrostatic screening against electromagnetic noise.
Circuit Protective Conductor (drain wire): An uninsulated tinned copper conductor in continuous contact with the aluminium screen, so the screen is earthed automatically. Sleeve it green-and-yellow and connect it to the earth terminal at every termination.
Outer Sheath: A robust, white or red Low Smoke Zero Halogen (LSOH) thermoplastic jacket that emits virtually no toxic halogens (such as hydrogen chloride) and minimal smoke when burned.
Standard vs. Enhanced Fire Performance (BS 5839-1)
British Standard BS 5839-1 (Fire detection and fire alarm systems for buildings) categorizes fire-resisting cables into two distinct performance tiers based on fire survival duration:
Performance Classification Testing Standard Test Duration & Stress Conditions Typical Building Applications
Standard Fire-Resisting Cable (e.g., FP200 Gold) BS EN 50200 Class PH30 (plus the BS 5839-1 requirements) Survives at least 30 minutes of fire with mechanical shock. Single-stage simultaneous evacuation buildings: low-rise offices, retail shops, single-story schools, standard commercial premises.
Enhanced Fire-Resisting Cable (e.g., Prysmian FP PLUS, or MICC) BS EN 50200 Class PH120 and BS 8434-2 120 minutes total: 60 minutes flame and shock, followed by 60 minutes flame, shock, and direct high-pressure water jet deluge . Phased-evacuation buildings: hospitals, high-rise residential towers (over 30 m), large multi-story shopping complexes, airports, and critical emergency voice evacuation (PA/VA) systems.
Note
In phased-evacuation buildings, occupants in immediate danger on the fire floor and the floor above are evacuated first, while other floors remain sheltered. The fire alarm wiring serving upper floors must withstand fire, falling debris, and firefighter water hose spray for up to 2 hours without signal loss, dictating the mandatory use of Enhanced fire-resisting cables.
Conductor Identification to BS 7671 Table 51
In 2004, the UK harmonized its cable conductor colour code with European CENELEC standard HD 308 S2 , incorporated into BS 7671 Table 51 (fully mandatory since 31 March 2006).
Harmonised vs. Pre-Harmonised Conductor Colours
- Conductor Function Pre-Harmonised UK Colours (Pre-2004) Harmonised BS 7671 Colours (Current Standard)
- Single-Phase: Line (L) Red Brown
- Single-Phase: Neutral (N) Black Blue
- Three-Phase: Line 1 (L1) Red Brown
- Three-Phase: Line 2 (L2) Yellow Black
- Three-Phase: Line 3 (L3) Blue Grey
- Three-Phase: Neutral (N) Black Blue
- Protective Conductor (PE / CPC) Green or Green-and-Yellow Green-and-Yellow (Bi-Colour)
- The Danger of Mixed Colours and Regulation 514.14.1
The introduction of harmonized colours introduced a critical trade hazard: in older UK installations, Black was Neutral, but in modern harmonised three-phase wiring, Black is Line 2 (Phase 2) . Furthermore, Blue was formerly Line 3, but is now Neutral!
To prevent electricians from mistakenly connecting a 400 V phase conductor to a neutral bar or touch-accessible equipment, BS 7671 Regulation 514.14.1 mandates:
Where an addition or alteration is made to an installation such that wiring to two different versions of BS 7671 coexists (pre-harmonised and harmonised colours), an indelible, clearly readable caution notice must be permanently affixed at or near the appropriate distribution board or consumer unit. ┌─────────────────────────────────────────────────────────────────┐
- │ CAUTION │
- │ This installation has wiring colours to two versions of │
- │ BS 7671. Great care should be taken before undertaking │
- │ extension, alteration or repair that all conductors are │
- │ correctly identified. │
- └─────────────────────────────────────────────────────────────────┘
Warning
Failure to install the dual-colour warning notice at a consumer unit or distribution board where new brown/blue cables interface with legacy red/black wiring constitutes a direct Code C3 (Improvement Recommended) or Code C2 (Potentially Dangerous) non-compliance on an Electrical Installation Condition Report (EICR).