Study guide

7.1 Polarity Verification & Earth Fault Loop Impedance (Ze, Zs)

City & Guilds 2391-51 Periodic Inspection & Testing of Electrical Installations Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Purpose & Statutory Framework of Periodic Inspection

1.1 Statutory Framework & Purpose of Periodic Inspection 1.2 BS 7671 Chapter 65 Requirements for Periodic Inspection & Testing 1.3 Recommended Inspection Intervals & Trigger Events

2 Chapter 2: Visual Inspection & Sampling Procedures

2.1 Visual Inspection Fundamentals on Existing Installations 2.2 Guidance Note 3 Sampling Principles & Justification 2.3 Sample Expansion & Defect Escalation Criteria

3 Chapter 3: Electrical Installation Condition Report (EICR) Structure

3.1 EICR Layout, Sections, Declarations & Summary of Condition 3.2 Compiling the Schedule of Inspections for Existing Installations 3.3 Schedule of Test Results, Circuit Details & Instrument Data

4 Chapter 4: EICR Classification Coding Principles (C1, C2, C3, FI)

4.1 Overview & Engineering Principles of Classification Codes 4.2 Code C1 (Danger Present) & Code C2 (Potentially Dangerous) Criteria 4.3 Code C3 (Improvement Recommended) & Code FI (Further Investigation) Criteria

5 Chapter 5: Classification Code Application & Practical Scenarios

5.1 Coding Scenarios: Earthing, Bonding & Shock Protection Defects 5.2 Coding Scenarios: Wiring Systems, Accessories & Thermal Effects 5.3 Overall Assessment Determination & Client Communication

6 Chapter 6: Selected Dead Tests on Existing Installations

6.1 Dead Testing Overview & Continuity of Protective Conductors 6.2 Ring Final Circuit Continuity Testing 6.3 Insulation Resistance Testing & Protection of Sensitive Equipment

7 Chapter 7: Selected Live Tests & RCD Verification

7.1 Polarity Verification & Earth Fault Loop Impedance (Ze, Zs) 7.2 Prospective Fault Current (PFC) & RCD Testing 7.3 Functional Testing & Voltage Drop Assessment

8 Chapter 8: Scope, Limitations & Safe Testing Procedures

8.1 Agreeing Extent, Operational & Agreed Limitations 8.2 Safe Isolation Procedures & GS38 Guidance 8.3 Risk Assessment & Restoring Installations to Service

9 Chapter 9: Test Result Interpretation, Temperature Correction & Certification

9.1 Interpreting Zs Values & The 80% Rule (Rule of Thumb) 9.2 Temperature Correction Factors & Historical Trend Analysis 9.3 Certification Sign-off, Competency & Instrument Calibration

7.1 Polarity Verification & Earth Fault Loop Impedance (Ze, Zs)

Key Takeaways Explain This Topic AI

Periodic inspection has no prescribed live-test order. Select and risk-assess each required measurement, and establish correct polarity before relying on results from an energised installation.

External earth fault loop impedance (Ze) is measured at the supply origin with the main switch locked open and the main earthing conductor isolated from the MET to eliminate parallel earth return paths.

Standard maximum benchmark Ze values published by DNOs are 0.35 Ω for TN-C-S (PME), 0.80 Ω for TN-S, and 21 Ω (up to 200 Ω under RCD protection) for TT earthing systems.

Total circuit earth fault loop impedance (Zs) is calculated as Zs = Ze + (R1 + R2) or measured directly; measured values at ambient temperature must not exceed 80% (0.8 multiplier) of BS 7671 Table 41.2–41.4 limits.

High-current 2-wire loop tests offer high accuracy (~25 A test current) on non-RCD circuits, while 3-wire non-trip (low-current/DC bias) tests prevent tripping 30 mA RCDs but require thermal stabilising time and path verification.

Last updated: July 2026

  • 7.1 Polarity Verification & Earth Fault Loop Impedance (Ze, Zs)
  • 1. Selecting Live Measurements During Periodic Inspection

Periodic inspection and testing has no recommended fixed sequence of dead and live tests. The inspector selects the type, order and extent of measurements from the installation condition, available records, agreed limitations and risk assessment.

Any live measurement must be justified and controlled because energised work introduces shock and arc hazards. Establish correct polarity by a suitable method before relying on a live test whose safe interpretation depends on polarity, and stop if the readings indicate an unsafe condition. This safety dependency does not turn the following topics into a universal mandatory sequence.

2. Live Polarity Verification Procedures

Live polarity testing confirms that all single-pole switching and protective devices (MCBs, fuses, switches) are connected exclusively in the line conductor, that the incoming supply conductors are connected to their correct respective terminals (Line to Line, Neutral to Neutral, Earth to Earth), and that center-contact Edison screw lamp holders have their center contact connected to the line conductor.

Live polarity is verified using a GS38-compliant approved two-pole voltage indicator and proving unit. Voltage measurements must be taken systematically across all live terminals:

Line-to-Neutral ( L − N L-N L − N ): Nominal supply voltage of 230 V AC (acceptable tolerance range 230 V +10% / -6%, i.e., 216.2 V to 253 V).

Line-to-Earth ( L − E L-E L − E ): Nominal supply voltage of 230 V AC (matching the L-N voltage in a healthy system).

Neutral-to-Earth ( N − E N-E N − E ): Nominal voltage of 0 V AC (practically < 5 V AC due to minor neutral volt drop under load).

If an inspector records 230 V between Neutral and Earth and 0 V between Line and Earth, a reversed polarity condition exists at the supply or distribution intake. Testing must immediately halt, the installation isolated, and the Distribution Network Operator (DNO) or installer notified.

3. External Earth Fault Loop Impedance ( Z e Z_e Z e ​ ) Measurement at Origin

External earth fault loop impedance ( Z e Z_e Z e ​ ) represents the impedance of the earth fault loop path external to the electrical installation. The loop path comprises:

The DNO supply transformer secondary winding.

The line conductor from the transformer to the installation intake.

The main earthing conductor and DNO return path back to the transformer neutral point (via cable sheath in TN-S, combined PEN conductor in TN-C-S/PME, or general mass of earth in TT).

Critical Isolation Procedure for Z e Z_e Z e ​

To measure true Z e Z_e Z e ​ accurately without measuring parallel paths created by structural steelwork, metallic gas/water services, or main protective bonding conductors, the following isolation protocol is strictly required:

Obtain permission to interrupt supply and perform safe isolation of the installation intake.

Lock the Main Switch in the OFF position .

Disconnect the Main Earthing Conductor from the Main Earthing Terminal (MET).

Connect the loop tester probes directly to the incoming supply side of the main switch (Line and Neutral) and the disconnected Main Earthing Conductor (Earth).

Execute a 2-wire high-current loop test.

Reconnect the Main Earthing Conductor to the MET immediately after test completion and verify tightness before closing the main switch.

CRITICAL SAFETY WARNING: While the main earthing conductor is disconnected from the MET during a Z e Z_e Z e ​ test, the installation is completely ungrounded. The main switch MUST remain locked OFF throughout the test duration to prevent any dangerous fault voltages from appearing on exposed metalwork.

DNO Benchmark Values for Z e Z_e Z e ​

The maximum declared Z e Z_e Z e ​ values published by UK Distribution Network Operators (BS 7671 / IET On-Site Guide) depend on the supply earthing arrangement:

  • TN-C-S (PME): Maximum declared Z e = 0.35 Ω Z_e = \mathbf{0.35\ \Omega} Z e ​ = 0.35 Ω
  • TN-S: Maximum declared Z e = 0.80 Ω Z_e = \mathbf{0.80\ \Omega} Z e ​ = 0.80 Ω

TT System: Maximum declared Z e = 21 Ω Z_e = \mathbf{21\ \Omega} Z e ​ = 21 Ω (values up to 200 Ω 200\ \Omega 200 Ω are acceptable provided RCD protection operates within required times).

4. Earth Fault Loop Impedance ( Z s Z_s Z s ​ ) & Temperature Correction (80% Rule)

Total earth fault loop impedance ( Z s Z_s Z s ​ ) at any point in a circuit is the sum of the external impedance ( Z e Z_e Z e ​ ) and the circuit protective conductor impedance ( R 1 + R 2 R_1+R_2 R 1 ​ + R 2 ​ ): Z s = Z e + ( R 1 + R 2 ) Z_s = Z_e + (R_1 + R_2) Z s ​ = Z e ​ + ( R 1 ​ + R 2 ​ )

Alternatively, Z s Z_s Z s ​ can be measured directly at the furthest point of the circuit using a loop impedance tester with the installation fully energised.

The 80% Rule (0.8 Temperature Correction Multiplier)

BS 7671 Tables 41.2, 41.3, and 41.4 publish maximum permitted Z s Z_s Z s ​ values based on conductors operating at their maximum permitted operating temperature ( 70 °C for thermoplastic/PVC insulated cables and 90 °C for thermosetting/XLPE cables) under fault conditions.

However, when an inspector measures Z s Z_s Z s ​ during a periodic inspection, the conductors are at ambient temperature (typically 20 °C ). Because copper conductor resistance increases with temperature at a rate of approximately 0.4% per °C (temperature coefficient α 20 = 0.004 \alpha_{20} = 0.004 α 20 ​ = 0.004 ), the measured cold value Z s ( meas ) Z_{s(\text{meas})} Z s ( meas ) ​ will be significantly lower than the hot fault value.

To account for this temperature rise, BS 7671 and C&G 2391-51 require the 80% Rule : Z s ( meas ) ≤ 0.8 × Z s ( max_tabulated ) Z_{s(\text{meas})} \le 0.8 \times Z_{s(\text{max\_tabulated})} Z s ( meas ) ​ ≤ 0.8 × Z s ( max_tabulated ) ​

If the measured Z s Z_s Z s ​ value exceeds 80% of the tabulated maximum, a detailed temperature calculation using Appendix 14 formulas is required, or the circuit must be flagged as non-compliant.

Protective Device Rating & Type Disconnection Time Tabulated Max Z s Z_s Z s ​ (BS 7671 Table 41.3) 80% Max Permitted Z s Z_s Z s ​ Limit (Rule of Thumb)

  • 6 A Type B MCB (BS EN 60898) 0.4 s / 5 s 7.28 Ω 7.28\ \Omega 7.28 Ω 5.82 Ω \mathbf{5.82\ \Omega} 5.82 Ω
  • 16 A Type B MCB (BS EN 60898) 0.4 s / 5 s 2.73 Ω 2.73\ \Omega 2.73 Ω 2.18 Ω \mathbf{2.18\ \Omega} 2.18 Ω
  • 32 A Type B MCB (BS EN 60898) 0.4 s / 5 s 1.37 Ω 1.37\ \Omega 1.37 Ω 1.10 Ω \mathbf{1.10\ \Omega} 1.10 Ω
  • 32 A Type C MCB (BS EN 60898) 0.4 s / 5 s 0.68 Ω 0.68\ \Omega 0.68 Ω 0.54 Ω \mathbf{0.54\ \Omega} 0.54 Ω
  • 32 A Type D MCB (BS EN 60898) 0.4 s / 5 s 0.34 Ω 0.34\ \Omega 0.34 Ω 0.27 Ω \mathbf{0.27\ \Omega} 0.27 Ω
  • 5. High-Current vs. Non-Trip Loop Testing Methodologies

When testing Z s Z_s Z s ​ on circuits protected by Residual Current Devices (RCDs or RCBOs), traditional 2-wire high-current loop tests (which inject a test current of 15 A to 25 A for 10 ms to 20 ms) will trip 30 mA RCDs instantly.

To overcome this, modern multifunction testers utilize two primary loop testing modes:

High-Current 2-Wire Test: Injects 20–25 A test current across Line and Earth. Provides exceptional measurement precision (resolution down to 0.01 Ω 0.01\ \Omega 0.01 Ω ) and immunises the result against parallel earth currents and noise. Used exclusively on non-RCD protected circuits, main distribution boards, and during Z e Z_e Z e ​ testing.

Non-Trip 3-Wire Test (Low-Current / DC Bias): Injects a low test current (typically < 15 mA <15\text{ mA} < 15 mA ) at a level intended not to operate the RCD, or applies a direct current (DC) saturation bias to saturate the core balance transformer of the RCD before injecting the measurement pulse.

Limitation: Non-trip tests are sensitive to electrical noise from operating loads (electronic ballasts, IT power supplies, VFDs) and can produce elevated or fluctuating impedance readings. Circuit loads should be turned off during non-trip testing to ensure accuracy.