Study guide
3.4 Why the Documents Exist: Reasons, Information Needed, Recording & Retention
City & Guilds 2391-52 Combined Inspection & Testing of Electrical Installations Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 About the 2391-52 Exam 1.2 How to Use This Guide & Open-Book Exam Strategy
2 Chapter 2: Statutory & Non-Statutory Documents
2.1 Statutory Documents 2.2 Non-Statutory Documents 2.3 Roles, Responsibilities & the Statutory/Non-Statutory Relationship
3 Chapter 3: Certification & Documentation
3.1 The Electrical Installation Certificate (EIC) & Schedules 3.2 The Minor Electrical Installation Works Certificate (MEIWC) 3.3 The Electrical Installation Condition Report (EICR) & Schedules 3.4 Why the Documents Exist: Reasons, Information Needed, Recording & Retention
4 Chapter 4: Initial Verification & Safe Isolation
4.1 Safe Isolation & Safety Management 4.2 Visual Inspection Requirements 4.3 Initial Verification: Requirements & Process 4.4 Additions & Alterations to an Existing Installation 4.5 Inspection Methods: The Senses, Verifying Items & IP Classification
5 Chapter 5: Sequence of Tests & Test Instruments
5.1 The Correct Sequence of Tests 5.2 Test Instruments: Selection, Calibration & Accuracy 5.3 Factors That Affect Test Results & Tests That May Be Unnecessary at Periodic Inspection
6 Chapter 6: Continuity Testing
6.1 Continuity of Protective Conductors (R1+R2) 6.2 Continuity of Ring Final Circuits (r1, rn, r2) 6.3 Main & Supplementary Protective Bonding Continuity
7 Chapter 7: Insulation Resistance & Polarity
7.1 Insulation Resistance Testing 7.2 Polarity Verification 7.3 Verifying SELV, PELV & Electrical Separation
8 Chapter 8: Earth Fault Loop Impedance
8.1 Ze & Zs Measurement 8.2 Zs Limits, Disconnection Times & the 0.8 Rule 8.3 Prospective Fault Current (PFC/PSCC)
9 Chapter 9: RCD & Earth Electrode Testing
9.1 RCD Testing 9.2 Earth Electrode Resistance on TT Systems
10 Chapter 10: Periodic Inspection & EICR Reporting
10.1 Purpose, Scope & Limitations of Periodic Inspection 10.2 Sampling & Extent of Inspection 10.3 Observation Classification Codes C1/C2/C3/FI 10.4 Outcomes, Inspection Intervals & Completing the EICR
11 Chapter 11: Phase Sequence, Functional Testing & Voltage Drop
11.1 Check of Phase Sequence 11.2 Functional Testing 11.3 Verification of Voltage Drop
12 Chapter 12: The 2391-502 Practical Assignment
12.1 The Practical Assignment & Establishing a Safe System of Work 12.2 Carrying Out the Practical: Inspection, Tests, Verification & Documentation
3.4 Why the Documents Exist: Reasons, Information Needed, Recording & Retention
Key Takeaways Explain This Topic AI
Assessment criterion 1.2 lists the reasons for inspection and testing: insurance, legislation, licensing, change of occupancy, change of use, substantial alteration or addition, and damage
Before starting, the inspector needs the design intent and previous certification, an agreed extent and limitations, and an agreed sampling regime - all three are recorded on the report
Initial verification certifies that new work complies at the moment it is energised; periodic inspection reports the condition of an installation already in service - different documents, different signatories, different test philosophies
Certificates and reports are the evidence of compliance with the Electricity at Work Regulations, so they are retained for the life of the installation and handed on at change of ownership
The certificate should be given to the person ordering the work, who passes it to the owner or occupier; the inspector keeps a copy
Last updated: August 2026
Why an Inspection Happens at All
Assessment criterion 1.2 asks you to explain reasons for conducting types of inspection and testing , and the qualification specification lists them explicitly. They are worth learning as a set, because a question will often give you a scenario and ask which reason applies.
- Reason What triggers it
- Insurance An insurer requires evidence that the installation is safe before cover is written or renewed
Legislation The Electricity at Work Regulations 1989 require systems to be maintained so as to prevent danger; the Landlord and Tenant legislation applying in each nation requires a current report for rented dwellings
Licensing Premises licensed for public entertainment, food, or houses in multiple occupation are commonly required by the licensing authority to hold a current report
Change of occupancy A new occupier may use the installation very differently from the last one
Change of use A building converted from, say, retail to a nursery brings different external influences and different protective requirements
Substantial alteration or addition New work triggers initial verification of that work and a check that the existing installation can support it
Damage Flood, fire, impact, vermin, or an overload event may have compromised insulation and terminations that look intact
The first three are essentially external obligations imposed on the duty holder; the last four are changes in the installation or its use. An exam scenario that mentions a landlord, an insurer, or a licence is pointing at the first group.
Information the Inspector Needs Before Starting
Assessment criterion 1.6 lists three things you must establish before any test lead is connected.
1. Information to carry out the work to BS 7671 and GN3
The design — circuit schedules, distribution board records, the intended use and the maximum demand.
Previous certification — the original Electrical Installation Certificate, any Minor Works Certificates, and the most recent Condition Report. These give you the baseline Ze, prospective fault current and earthing arrangement, and tell you what has changed.
The characteristics of the supply — earthing arrangement, nominal voltage, number of phases, and the protective device at the origin.
Details of any special locations or equipment on site that bring additional requirements.
Where records do not exist — common on older installations — that absence is itself a finding. The inspector must then determine the supply characteristics by measurement and enquiry, and record the lack of records on the report.
2. Agreeing the extent and limitations
The extent is what the inspection covers: the whole installation, one distribution board, one floor. The limitations are what it does not cover, and they come in two flavours — those agreed with the client in advance (not lifting fitted floor coverings, not shutting down a server room) and those the inspector meets on the day (a locked plant room, a sealed accessory). Both are recorded.
Agreeing this in writing before starting protects everybody. The client knows what they are buying; the inspector knows what they are responsible for; and the person who reads the report in three years knows what was never looked at.
3. Determining the sampling regime
Periodic inspection is carried out on a sample rather than 100% of the installation. The proportion is the inspector’s professional judgement based on age, condition, usage and the records available — and it is agreed with the client, recorded on the report, and extended if defects appear. Sampling is covered fully in section 10.2.
Initial Verification and Periodic Inspection Compared
Assessment criterion 1.3 asks you to compare the two processes. The comparison is worth holding as a table, because exam stems frequently describe one and offer answers drawn from the other.
- Initial verification Periodic inspection and testing
- Applies to New installations, and new work added to an existing one An installation already in service
Question being answered Does this comply with BS 7671 and is it safe to energise? Is this in a satisfactory condition for continued use?
Document issued Electrical Installation Certificate, or Minor Electrical Installation Works Certificate Electrical Installation Condition Report
Extent 100% of the new work An agreed sample, extended where defects appear
Sequence Prescribed: dead tests before live tests Not prescribed — live tests often come first, to establish it is safe to isolate
Signatories Design, construction, and inspection and testing (may be one person, or three) The inspector, plus whoever authorises the report for issue
Deficiencies Corrected and re-tested before the certificate is issued Recorded as coded observations; the inspector does not normally rectify
Non-compliance with the current edition Must be corrected, or recorded as a departure Judged on whether it presents danger, not on whether it matches the latest text
The last row is the one candidates most often get wrong. An installation wired to the 16th Edition is not automatically unsatisfactory because it no longer matches BS 7671:2018+A4:2026. The inspector asks whether the deviation presents or may present danger .