Study guide

7.2 Polarity Verification

City & Guilds 2391-52 Combined Inspection & Testing of Electrical Installations Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 About the 2391-52 Exam 1.2 How to Use This Guide & Open-Book Exam Strategy

2 Chapter 2: Statutory & Non-Statutory Documents

2.1 Statutory Documents 2.2 Non-Statutory Documents 2.3 Roles, Responsibilities & the Statutory/Non-Statutory Relationship

3 Chapter 3: Certification & Documentation

3.1 The Electrical Installation Certificate (EIC) & Schedules 3.2 The Minor Electrical Installation Works Certificate (MEIWC) 3.3 The Electrical Installation Condition Report (EICR) & Schedules 3.4 Why the Documents Exist: Reasons, Information Needed, Recording & Retention

4 Chapter 4: Initial Verification & Safe Isolation

4.1 Safe Isolation & Safety Management 4.2 Visual Inspection Requirements 4.3 Initial Verification: Requirements & Process 4.4 Additions & Alterations to an Existing Installation 4.5 Inspection Methods: The Senses, Verifying Items & IP Classification

5 Chapter 5: Sequence of Tests & Test Instruments

5.1 The Correct Sequence of Tests 5.2 Test Instruments: Selection, Calibration & Accuracy 5.3 Factors That Affect Test Results & Tests That May Be Unnecessary at Periodic Inspection

6 Chapter 6: Continuity Testing

6.1 Continuity of Protective Conductors (R1+R2) 6.2 Continuity of Ring Final Circuits (r1, rn, r2) 6.3 Main & Supplementary Protective Bonding Continuity

7 Chapter 7: Insulation Resistance & Polarity

7.1 Insulation Resistance Testing 7.2 Polarity Verification 7.3 Verifying SELV, PELV & Electrical Separation

8 Chapter 8: Earth Fault Loop Impedance

8.1 Ze & Zs Measurement 8.2 Zs Limits, Disconnection Times & the 0.8 Rule 8.3 Prospective Fault Current (PFC/PSCC)

9 Chapter 9: RCD & Earth Electrode Testing

9.1 RCD Testing 9.2 Earth Electrode Resistance on TT Systems

10 Chapter 10: Periodic Inspection & EICR Reporting

10.1 Purpose, Scope & Limitations of Periodic Inspection 10.2 Sampling & Extent of Inspection 10.3 Observation Classification Codes C1/C2/C3/FI 10.4 Outcomes, Inspection Intervals & Completing the EICR

11 Chapter 11: Phase Sequence, Functional Testing & Voltage Drop

11.1 Check of Phase Sequence 11.2 Functional Testing 11.3 Verification of Voltage Drop

12 Chapter 12: The 2391-502 Practical Assignment

12.1 The Practical Assignment & Establishing a Safe System of Work 12.2 Carrying Out the Practical: Inspection, Tests, Verification & Documentation

7.2 Polarity Verification

Key Takeaways Explain This Topic AI

Polarity verification confirms every single-pole switch, fuse, and circuit breaker is in the phase (line) conductor only — not the neutral — and that ES lampholders have the centre contact on phase

A switch in the neutral leaves the load live when "off", which is lethal for maintenance; an ES lampholder with the outer thread on phase is a shock hazard when changing a lamp

Dead polarity (test #4) is continuity-based: link phase and CPC at the board, then test at each accessory with the switch toggled ON and OFF to confirm the switch breaks the phase

Live polarity is confirmed after energisation using an approved voltage indicator: L–N ≈ 230 V, L–E ≈ 230 V, N–E ≈ 0 V at each socket/outlet

  • Polarity is recorded on the schedule of inspections and the schedule of test results
  • Last updated: August 2026

7.2 Polarity Verification

Quick Answer: Polarity verification confirms that every single-pole protective device, switch, and fuse is connected in the phase (line) conductor only , that Edison-screw (ES) lampholders have the centre contact connected to phase, and that socket outlets are correctly wired. Polarity is checked dead (during continuity, test #4) and confirmed live after energisation.

Purpose

Polarity verification is dead test #4 (and is also confirmed live after energisation). It confirms that:

Every single-pole switch, fuse, and circuit breaker is connected in the phase (line) conductor only — not the neutral

  • Edison-screw (ES) lampholders have the centre contact connected to phase and the outer screw thread to neutral
  • Socket outlets have the phase conductor on the correct terminal
  • Why It Matters

A single-pole switch in the neutral conductor leaves the load energised (live) when the switch is "off" — lethal for anyone undertaking maintenance who believes the circuit is isolated. An ES lampholder with the outer screw thread on phase presents a shock hazard when changing a lamp, since the exposed thread is touchable while the lamp is being inserted or removed. Correct polarity is therefore a fundamental safety requirement.

Dead Test Method (Continuity-Based)

With the supply isolated:

Link phase and CPC at the distribution board (as for the R1+R2 continuity test).

At each accessory, test between the switched phase terminal and the CPC:

With the switch ON — a low reading confirms continuity through the phase conductor and switch.

With the switch OFF — a high reading confirms the switch breaks the phase conductor. If the reading stays low with the switch off, the switch is in the wrong conductor (neutral) or is bypassed.

For socket outlets , test between the phase pin and the CPC terminal at the socket — a low reading confirms the phase conductor is on the correct terminal (consistent with the continuity method).

This method simultaneously verifies continuity of the phase conductor and confirms that single-pole switching devices are in the phase conductor.

Live Test Method (After Energisation)

After the installation is energised, use an approved voltage indicator to confirm polarity at each socket/outlet. The instrument must be proved on a known live source before and after each test — the prove-test-prove sequence required by GS38 and the HSE guidance on electrical test equipment:

Prove the indicator on the proving unit or a known live supply — confirm all indicators function.

Test at the accessory — confirm L–N, L–E, and N–E readings.

Prove again on the known live source — confirm the indicator still functions.

This three-point sequence guards against a failed indicator producing a false "dead" reading. The expected readings at a correctly wired single-phase socket are:

  • L–N ≈ 230 V (single-phase nominal)
  • L–E ≈ 230 V
  • N–E ≈ 0 V (no significant voltage between neutral and earth)

These readings confirm phase is on the correct terminal. If L–E reads ~0 V and N–E reads ~230 V, the phase and neutral have been transposed. A reading of 0 V across all three combinations suggests a lost supply or a faulty indicator — re-prove the instrument before concluding the circuit is dead.

Why Both Dead and Live Tests?

The dead continuity-based test confirms the wiring topology before energisation — that the switch is in the phase conductor and the socket terminals are correctly allocated. The live test confirms the same outcome under real conditions after the supply is connected, and catches any error introduced during final connection at the board or at the accessory. Both are required because either test alone can miss a fault: a dead test cannot reveal a phase-neutral transpose introduced at the final connection, and a live test on its own does not confirm that the switch breaks the phase (it only confirms terminal voltages).

Edison-Screw (ES) Lampholders

For ES lampholders, the centre (eye) contact must be connected to the phase conductor and the outer screw thread to neutral. Polarity testing (dead or live) confirms this arrangement. BC (bayonet cap) lampholders do not have a polarised contact and do not require polarity confirmation at the holder, though the switch must still be in the phase conductor.

Dead vs Live Polarity — Summary Table

  • Aspect Dead polarity test Live polarity test
  • Test # #4 (dead) Confirmed live after energisation

Method Continuity: link phase + CPC at board, test at accessory with switch ON/OFF Approved voltage indicator at each outlet: L–N, L–E, N–E

Confirms Switch/fuse/circuit breaker in phase conductor; socket terminal allocation; ES centre on phase Phase on correct terminal at socket/outlet; no phase-neutral transpose

  • State Installation isolated Installation energised
  • Recording

Polarity is recorded on the schedule of inspections (confirmed as satisfactory) and the schedule of test results . Both the dead continuity-based check and the live confirmation contribute to the overall polarity verification.

Worked Example

A radial socket circuit is tested dead with phase and CPC linked at the board. At the first socket, the tester measures between the phase pin and CPC and reads 0.35 Ω — low, confirming the phase conductor is continuous and on the correct terminal. At the switch controlling an outside light, with the switch ON the reading is 0.4 Ω and with the switch OFF the reading is >999 Ω (open circuit), confirming the switch breaks the phase conductor. After energisation, the tester confirms L–N = 230 V, L–E = 230 V, N–E = 0 V at the socket. Polarity is satisfactory and recorded.