Study guide

8.3 Estimating Annual Yield

City & Guilds 2922-34 Level 3 Award in the Installation and Maintenance of Small Solar Photovoltaic Systems Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 Current Exam Facts 1.2 Eligibility, Currency and Industry Recognition 1.3 Assessment Format and Permitted Materials

2 Key Documentation and Legislation

2.1 Health, Safety and Continuity Law 2.2 Building Regulations and Planning Permission 2.3 Waste, Transport and Battery Fire Documents

3 Non-Statutory Standards and Industry Guidance

3.1 BS 7671, IET Codes of Practice and Guidance Notes 3.2 MCS Standards MIS 3002, MIS 3012 and MGD Guides 3.3 Fire Guidance, Grid Codes and Manufacturer Instructions

4 Working Safely with Solar PV Systems

4.1 PV Electrical Hazards 4.2 Risk Assessment, Method Statements, Height and PPE 4.3 Dual-Supply Isolation and Prove-Dead

5 PV Cells, Modules and I-V Behaviour

5.1 Silicon Cell Technologies 5.2 Module Types and Building Integration 5.3 The I-V Curve, Irradiance, Temperature and Shading

6 Inverters, Inverter Functions and Metering

6.1 Inverter Types 6.2 Inverter AC, DC and Energy-Management Functions 6.3 Utility and Generation Metering

7 Array Behaviour, Architectures and Nameplate Symbols

7.1 Reverse Currents, Bypass Diodes and PID 7.2 Array Architectures 7.3 STC and Manufacturer Symbols

8 Site Performance: Pitch, Shade and Yield

8.1 Pitch, Orientation and Location 8.2 Shading, Loss Stack and MGD 005 8.3 Estimating Annual Yield

9 Array Capacity, DNO Connection and Equipment Siting

9.1 Calculating Maximum Array Capacity 9.2 G98, G99, G100 and Combined Generation 9.3 Equipment Siting and Permissions

10 DC Voltage, Current and Overcurrent Protection

10.1 DC Voltage and Current Multipliers 10.2 String Overcurrent Protection Rule 10.3 DC Circuit-Breakers and gPV Fuses

11 DC Isolation, Combiners, Connectors and Cables

11.1 DC Isolation and Switching 11.2 Combiner Boxes and PV Connectors 11.3 DC Cables and Earth-Fault Causes

12 DC Fault Monitoring, Surge Protection and Inverter Sizing

12.1 Insulation Monitoring, RCM and Earth-Fault Alarms 12.2 Electromagnetic Interference and DC Surge Protection 12.3 Inverter Sizing and the MPP Window

13 Inverter Location, AC Side and Labelling

13.1 Inverter Specification and Location 13.2 AC Isolation and G99 Relays 13.3 AC Cables, Voltage Drop and RCDs 13.4 Labelling the PV System

14 Testing, Commissioning, Handover and Maintenance

14.1 Initial Verification and DC Inspection 14.2 Minimum and Additional DC Tests 14.3 Handover, Client Briefing and Maintenance

15 Prosumer Installations, EEMS and Storage

15.1 Prosumer Terms and Vehicle Storage 15.2 Integrated Energy Management and the Smart Grid 15.3 G100 Export Limitation and Why Add Storage

8.3 Estimating Annual Yield

Key Takeaways Explain This Topic AI

Handbook v1.3 outcome 4.1.2 treats annual yield as a documented calculation: performance software or tools plus MCS rules where the job is an MCS estimate.

The MCS Appendix B annual figure is total generation in kilowatt-hours per year = kWp × Kk × SF, with kWp equal to the sum of STC nameplate watts.

Appendix B inputs are postcode zone, pitch to the nearest 1°, azimuth relative to due south to the nearest 5°, Kk from the MCS zone tables (Climate-SAF-PVGIS × 0.8), and SF from the shade method.

A worked teaching example is 4.3 kWp × 850 kWh/kWp × 0.94 = 3435.7 kWh/year.

Alternative software may be shown but must not outrank the MCS table estimate; if the software figure is much higher, state the assumptions and include the required caution wording.

Last updated: September 2026

8.3 Estimating annual yield

Quick Answer: Handbook v1.3 learning outcome 4.1.2 asks how you estimate yearly generation: with performance-calculation software or tools , and with MCS requirements where they apply . For an MCS-style estimate, MIS 3002 Appendix B is blunt: annual alternating-current output (kWh/year) = kWp × Kk × SF . kWp is the sum of the STC nameplate figures printed on the module labels. Kk is kilowatt-hours per kilowatt-peak from the postcode-zone tables (Climate-SAF-PVGIS data × 0.8 ). SF is the shading factor from section 8.2. A teaching example with realistic made-up table values is 4.3 kWp , Kk = 850 kWh/kWp , SF = 0.94 → 4.3 × 850 × 0.94 = 3435.7 kWh/year . Proprietary software may add a second figure, but it must not outrank the MCS estimate and needs caution wording if it is much higher.

Independent ExamFinch teaching uses the published Appendix B method and the handbook 4.1.2 information list. ExamFinch does not issue MCS certificates and does not replace the live tables on the MCS website.

Two approaches, one exam expectation

4.1.2 is not "pick a nice yearly number." It is "show the approach." On a non-MCS conversation you might use manufacturer software, a commercial design package or a spreadsheet, provided you can describe the irradiance files and the shade method. On a job that needs an MCS performance estimate, Appendix B is the standard method. Extra software is allowed as an additional estimate only if you:

  • clearly describe and justify the approach and the factors used,
  • give that extra figure no greater prominence than the MCS table result, and

add the warning text that the extra figure should be treated with caution if it is significantly better than the standard method.

A salesperson who quotes 50% above the MCS product and hides the table result has failed that rule, not "found a better climate."

The Appendix B arithmetic

Work in this order so an assessor can reconstruct the sheet:

Sum kWp from every module's STC data-plate watt-peak. Ten 430 W modules are 4.3 kWp , not "about 4 kW" and not the inverter's AC rating.

Read postcode zone from the MCS map and zone table (the same family of zones as SAP).

Measure pitch from horizontal and round to the nearest 1° .

Measure azimuth relative to due south and round to the nearest 5° (south 0°, south-east or south-west 45°, east or west 90°).

Look up Kk in that zone's table for that pitch and azimuth. Do not apply another 0.8 by hand; the published Kk already includes Climate-SAF-PVGIS × 0.8 .

Determine SF (1.00 if obviously clear; otherwise MGD 005 NS method or 1 − estimated fractional loss).

Multiply kWp × Kk × SF .

Worked example (teaching numbers, not a live table cell):

  • kWp = 4.3
  • Kk = 850 kWh/kWp (a realistic made-up look-up for this chapter)
  • SF = 0.94 (for example NS = 6 → 1 − 0.06 = 0.94)

First, 4.3 × 850 = 3655 kWh if the site were unshaded at that Kk.

Then 3655 × 0.94 = 3435.7 kWh/year.

Write the product as 3435.7 kWh/year (or the integer your centre's sheet format uses) and keep the three factors visible. If a colleague only writes "about 3,400 kWh," the assessor cannot see whether Kk or SF was dropped.

A 50% higher sales figure on the same system would be 3435.7 × 1.5 ≈ 5154 kWh/year . That gap is exactly the situation Appendix B warning text is for: keep 3435.7 kWh as the MCS estimate, explain the software assumptions, and do not lead the quote with 5154 kWh as if it replaced the table.

Information the handbook expects you to be able to state

Outcome 4.1.2 is as much a documentation outcome as a calculator outcome. Be ready to list:

Total generation (kWh/year) = kWp × Kk × SF and the three numbers you used.

Model and manufacturer of the modules and of the inverters (the estimate is for a named kit, not "a typical panel").

Nominal array power (the kWp you summed).

Array orientation and pitch (the rounded Appendix B values).

Site location (address / postcode zone, not "southern England").

Details of irradiance files if you used software (which dataset, which year range, which transposition model). For a pure MCS table estimate, the irradiance story is the published Kk source: Climate-SAF-PVGIS × 0.8.

Description of shade methods (MGD 005 NS count, clear-horizon SF = 1.00, or a defended alternative).

Financial assumptions if the pack includes payback, export tariff, self-consumption fraction, inflation or discount rate. An energy number and a money number are different claims. If you did not do finance, say so; do not let a payback slide inherit an unexplained tariff.

MCS also wants the pre-sale table in a recognisable shape: installed kWp (STC), orientation in degrees from south, inclination from horizontal, postcode region, Kk from the table, SF, and estimated annual output as the product. If the site was only evaluated remotely, Appendix B requires extra wording that orientation, inclination or shading were estimated and that actual performance may be significantly lower or higher.

  • Estimate input What you record Common fail
  • kWp Sum of STC nameplates Using inverter AC kW or rounding 4.3 down to 4
  • Postcode zone MCS / SAP zone for the site Borrowing a neighbour's southern Kk
  • Pitch Degrees from horizontal, nearest 1° Guessing "about 35" on a 15° felt garage
  • Azimuth Degrees from due south, nearest 5° Calling every roof "south"
  • Kk Table cell for zone, pitch, azimuth Multiplying the published Kk by 0.8 a second time
  • SF 1.00, or 1 − (NS × 0.01), or 1 − fractional loss Setting 1.00 because optimisers were quoted
  • Kit identity Module and inverter make/model "Tier-1 panels" with no model
  • Irradiance / shade notes Files used, or "MCS Kk + MGD 005" Silent software with no method
  • Finance (if any) Tariff, self-use fraction, inflation Payback with hidden assumptions

In practice: A salesperson emails a 3-D render that claims about 5,150 kWh/year for the 4.3 kWp garage array. Your Appendix B sheet, using Kk = 850 kWh/kWp and SF = 0.94, is 3435.7 kWh/year . You do not average 5150 and 3436. You do not delete the MCS line because the render looks expensive. You print 3435.7 kWh as the MCS estimate, attach the software figure as a secondary estimate with the factors named, and include the caution that a much higher figure should be treated with care. If the render used a different pitch, ignored the chimney, or skipped the 0.8 already inside Kk, that is a method problem, not proof that the table is "out of date."

What the product is, and what it is not

The Appendix B product is an estimated annual alternating-current yield for customer information and MCS documentation. It is not a guarantee, not a winter-month forecast, and not a self-consumption figure. Self-consumption, if quoted, is a separate calculation with occupancy and (if storage is involved) a clear statement about electrical-energy-storage certification. Do not let a yearly kWh line quietly become "this is what the bills will fall by."

If two roof planes exist, estimate each plane (its own kWp, pitch, azimuth, SF) and add the kilowatt-hours. One blended heading with one SF is how 4.1.2 documentation fails even when the arithmetic looks tidy.

The exam will try to skip a factor, swap inverter kW for module kWp, or let a glossy software number outrank the table. Slow down: nameplates → zone → pitch → azimuth → Kk → SF → multiply → show the working → keep extra software in its place.

Loading diagram... Appendix B annual yield path