Study guide

14.3 EAL Practical Assessment Structure & Inspection Rig Scenarios

EAL Level 3 Inspection & Testing Awards Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Qualification Overview & Regulatory Framework

1.1 EAL Level 3 Qualification Structure & Examination Specifications 1.2 Statutory Framework & Electricity at Work Regulations 1989 1.3 Non-Statutory Standards: BS 7671:2018+A4:2026 and IET Guidance Note 3

2 Chapter 2: Health, Safety & Safe Isolation Procedures

2.1 Safe Isolation Principles & Step-by-Step Procedure 2.2 Test Equipment Safety & HSE Guidance Note GS38 2.3 Live Working Precautions, Risk Assessment & PPE

3 Chapter 3: Documentation, Certification & Reporting

3.1 Purpose of Initial Verification vs Periodic Inspection 3.2 Electrical Installation Certificates (EIC) & Signatories 3.3 Minor Electrical Installation Works Certificates (MEIWC) 3.4 Electrical Installation Condition Reports (EICR) & Extent/Limitations

4 Chapter 4: Safe Inspection: Supply, Earthing & Intake Equipment

4.1 Visual Inspection Principles & Methodology 4.2 Supply Intake, Metering & Distribution Network Operator Equipment 4.3 Earthing Arrangements & Protective Bonding Conductors

5 Chapter 5: Safe Inspection: Distribution Boards, Circuits & Enclosures

5.1 Distribution Boards & Consumer Units Inspection 5.2 Protective Devices, Switchgear & Coordination 5.3 Wiring Systems, Cable Selection & Installation Methods

6 Chapter 6: Safe Inspection: Routing, Protection & Special Locations

6.1 Cable Concealment, Safe Zones & Mechanical Protection 6.2 External Influences & Enclosure IP Ratings 6.3 Special Installations, Locations & Modern Technologies

7 Chapter 7: Condition Reporting & EICR Classification Coding

7.1 EICR Classification Coding: Code C1 (Danger Present) 7.2 EICR Classification Coding: Code C2 (Potentially Dangerous) 7.3 EICR Classification Coding: Code C3 & Code FI

8 Chapter 8: Safe Testing: Preparation, Sequence & Instruments

8.1 The Prescribed Testing Sequence 8.2 Test Instrument Standards & BS EN 61557 8.3 On-Site Safety Precautions & Client Coordination During Testing

9 Chapter 9: Dead Testing: Continuity of Protective Conductors

9.1 Continuity Testing Method 1 (R1 + R2) 9.2 Continuity Testing Method 2 (R2 Wandering Lead) 9.3 Main Protective Bonding Conductor Continuity

10 Chapter 10: Dead Testing: Continuity of Ring Final Circuits

10.1 Ring Final Circuit Testing: End-to-End Measurements 10.2 Ring Final Circuit Testing: Interconnection & Cross-Connection 10.3 Ring Circuit Fault Diagnosis & Reading Interpretation

11 Chapter 11: Dead Testing: Insulation Resistance & Polarity

11.1 Insulation Resistance Testing Principles & Precautions 11.2 Insulation Resistance Test Voltages & Minimum Values 11.3 Dead Polarity Testing Methods & Verification 11.4 Earth Electrode Resistance Testing

12 Chapter 12: Live Testing: Earth Fault Loop Impedance (Zs & Ze)

12.1 External Earth Fault Loop Impedance (Ze) Measurement 12.2 Circuit Earth Fault Loop Impedance (Zs) Measurement & Calculation 12.3 The 0.8 Temperature Correction Rule & Maximum Permitted Zs 12.4 Prospective Fault Current (PFC / Ipf) Testing

13 Chapter 13: Live Testing: RCDs, Phase Sequence & Functional Tests

13.1 RCD Operating Principles, Characteristics & Types 13.2 RCD Testing Procedures & Maximum Disconnection Times 13.3 Phase Sequence, Voltage Drop & Additional Functional Testing 13.4 Fault Finding & Diagnostic Methodology in Electrical Testing

14 Chapter 14: Commissioning, Handover & Practical Assessment Mastery

14.1 Initial Energisation & Final Commissioning Sequence 14.2 Completing Schedules of Inspections & Schedules of Test Results 14.3 EAL Practical Assessment Structure & Inspection Rig Scenarios 14.4 Common Candidate Errors & Exam Traps

14.3 EAL Practical Assessment Structure & Inspection Rig Scenarios

Key Takeaways Explain This Topic AI

Under EAL Qualification Specification Issue 5 (Section 6), each qualification requires two centre-marked practical assessments: Initial Verification requires Practical 1 (Initial Inspection) and Practical 2 (Initial Verification Assessment); Periodic Inspection and the Combined Award require Practical 1 (Periodic Inspection) and Practical 2 (Periodic Inspection and Testing Assessment).

Practical assessment grading is strictly Pass or Refer; under EAL re-assessment policy, a candidate who is referred is required to retake ONLY the referred task element following centre feedback and appropriate remedial tuition.

Distinguish EAL’s published assessment requirements from revision exercises and centre arrangements. The four activities in this section are original study examples; obtain actual assessment resources, timing and instructions through the authorized centre process.

Safe isolation and live-test precautions are essential practical competences. Follow the centre’s authorized assessment instructions; the public specification does not publish an automatic-referral rule for every listed omission or a universal ten-step marking rubric.

A necessary live separate Ze measurement requires full EAWR14 justification, all-source isolation of outgoing circuits, diverted-current precautions and suitable equipment/PPE. Restore and verify required earthing before outgoing energisation; do not treat main-switch-OFF alone as sufficient.

Last updated: November 2026

14.3 EAL Practical Assessment Structure & Inspection Rig Scenarios

Core Examination Standard: The EAL Level 3 Inspection & Testing qualifications evaluate candidates through rigorous, centre-marked practical assessments governed by Section 6 of EAL’s published IT3 qualification specification . The practical assessments are set by EAL and marked by the approved centre, with internal standardisation and external quality assurance. Their detailed tasks and resources belong to the authorized assessment packs.

Official EAL Practical Assessment Structure (Issue 5, Section 6)

In official EAL documentation, practical assessment across all three qualifications is structured around two centre-marked practical assessments : OFFICIAL EAL PRACTICAL ASSESSMENT SUITE (ISSUE 5, SECTION 6)

  • ┌────────────────────────────────────────────────────────────────────────┐
  • │ INITIAL VERIFICATION QUALIFICATION (QN: 600/4337/4 - UNIT QIT3/001) │
  • │ • Practical 1: Initial Inspection Assessment │
  • │ • Practical 2: Initial Verification Assessment │
  • ├────────────────────────────────────────────────────────────────────────┤
  • │ PERIODIC INSPECTION QUALIFICATION (QN: 600/4338/6 - UNIT QCR/001) │
  • │ • Practical 1: Periodic Inspection Assessment │
  • │ • Practical 2: Periodic Inspection and Testing Assessment │
  • ├────────────────────────────────────────────────────────────────────────┤
  • │ COMBINED QUALIFICATION (QN: 603/2625/6 - UNIT ITC3/001) │
  • │ • Practical 1: Periodic Inspection Assessment │
  • │ • Practical 2: Periodic Inspection and Testing Assessment │
  • └────────────────────────────────────────────────────────────────────────┘
  • Official Grading: Pass or Refer Only

Under EAL regulations, practical assessments are graded strictly as Pass or Refer . Meet the required criteria in the authorized assessment instructions; the public qualification specification does not publish a universal numerical or automatic-referral rubric.

Official EAL Re-Assessment Policy

EAL’s published IT3 qualification specification (Section 6) defines a clear, candidate-centered re-assessment policy:

Retake Referred Task Element Only: If a candidate fails to achieve a Pass in any practical assessment element, they are required to retake ONLY the referred task element (not the entire assessment suite, and not previously passed units or elements).

Mandatory Feedback & Remedial Tuition: The re-assessment may take place only after the candidate receives structured feedback detailing their specific shortfall and completes appropriate remedial tuition from the assessment centre.

Specification Mandates vs. Training Centre Implementation Practices

Candidates must clearly distinguish between the official EAL qualification specification and the operational delivery practices established by accredited training centres:

Note

Training activities and formal assessments: The four activities below organise revision; they are original teaching examples, not disclosed EAL assessment tasks or a claim that every centre follows four timed stages. EAL requires formal assessment rigs to be kept secure and prohibits their use for prior training. Practise on separate training resources. Obtain assessment arrangements and permitted materials from the centre without requesting confidential assessor content.

Training Activity 1: Safe Isolation Protocol (Single & Three-Phase)

Demonstrate safe isolation with appropriate planning, equipment and checks. EAWR12/13 address isolation and preventing re-energisation; EAWR14 applies to necessary work on/near live conductors. Follow the authorized assessment instructions and demonstrate the required safe actions. ILLUSTRATIVE SAFE-ISOLATION CHECKLIST

  • ┌────────────────────────────────────────────────────────────────────────┐
  • │ 1. PLAN: Consult dutyholder; identify work boundary and every source. │
  • │ 2. IDENTIFY: Locate and verify correct isolating switch disconnector. │
  • │ 3. INSPECT TESTER: Inspect GS38 two-pole detector & dedicated proving unit.│
  • │ 4. FIRST PROVE: Prove voltage detector against suitable proving source immediately.│
  • │ 5. ISOLATE: Secure every relevant source to the work boundary. │
  • │ 6. LOCK-OFF & TAG: Fit lock-off bracket, unique padlock, and safety tag.│
  • │ Retain key directly in your pocket (never leave on bench/in lock). │
  • ├────────────────────────────────────────────────────────────────────────┤
  • │ 7. PROVE DEAD ACROSS ALL CONDUCTOR COMBINATIONS: │
  • │ • Single-Phase (3 tests): L-N, L-E, N-E │
  • │ • Three-Phase (10 tests): L1-L2, L2-L3, L3-L1, │
  • │ L1-N, L2-N, L3-N, │
  • │ L1-E, L2-E, L3-E, N-E │
  • ├────────────────────────────────────────────────────────────────────────┤
  • │ 8. SECOND PROVE: Re-prove detector on the suitable source immediately after. │
  • │ 9. VERIFY PROXIMITY: Ensure adjacent equipment remains safe / shielded. │
  • │ 10. WORK: Only within the proved-dead boundary and agreed safe system. │
  • └────────────────────────────────────────────────────────────────────────┘

Caution

Prove the detector before and after checking dead. Use an appropriate two-pole voltage indicator, inspected with its leads and checked on a proving unit or suitable known source. A general multimeter is not the recommended proving-dead instrument: wrong range/connections or other failures can mislead. Test all relevant conductor combinations at the work point, including neutral-to-earth, and protect against adjacent live parts. Retain control of the isolation key and consider stored energy and alternative supplies. An accessible supply-side terminal may remain live even though downstream circuits are isolated.

Training Activity 2: Visual Inspection Scenarios

Use a separate training installation or original photographs to practise recognizing defects. The following are teaching examples; the official pack determines assessment resources and methods.

Candidates must inspect the installation systematically against BS 7671 Section 642 / Section 652 and record each defect clearly on an observation schedule. ILLUSTRATIVE VISUAL INSPECTION DEFECTS

  • ┌────────────────────────────────────────────────────────────────────────┐
  • │ 1. INGRESS PROTECTION (IP) DEFECTS │
  • │ • Open top knockout permits access to live parts; required IP not met│
  • │ • Missing blanking piece exposing live busbar / terminal (fails IPXXB) │
  • ├────────────────────────────────────────────────────────────────────────┤
  • │ 2. ENCLOSURE AND ASSEMBLY DEFECTS │
  • │ • Missing/unsuitable component compromising the verified assembly │
  • │ • Unsealed entry fails required IP or maker’s assembly arrangement│
  • ├────────────────────────────────────────────────────────────────────────┤
  • │ 3. CABLE ROUTING & MECHANICAL PROTECTION DEFECTS │
  • │ • Unprotected sharp stud edge can damage a cable at the penetration │
  • │ • Shallow concealed cable lacks prescribed-zone/alternative protection │
  • ├────────────────────────────────────────────────────────────────────────┤
  • │ 4. ACCESSORY POLARITY & SWITCHING ERRORS │
  • │ • Wrong polarity at ES centre contact where643.6 requires line; note E14/E27 exception │
  • │ • Single-pole light switch connected in the neutral conductor │
  • ├────────────────────────────────────────────────────────────────────────┤
  • │ 5. EARTHING & BONDING NON-COMPLIANCES │
  • │ • Main protective bonding conductor undersized (e.g. 4 mm² on PME) │
  • │ • Missing 'Safety Electrical Connection - Do Not Remove' warning label │
  • └────────────────────────────────────────────────────────────────────────┘
  • Training Activity 3: Testing and Verification

Practise on a separate training resource with identified circuits, equipment and sources. The actual formal-assessment installation and instructions are specified in EAL’s authorized pack, not a universal lighting/ring/cooker rig defined by this guide.

Planning the Verification

For initial verification, perform the relevant 643.2–643.6 dead tests in their required order. Prepare and check suitable instruments/leads; verify protective-conductor and ring continuity, insulation resistance, applicable SELV/PELV/separation and floor/wall measures, then polarity. Use the correct voltage and precautions for the circuit/equipment rather than 500 V for everything. PLAN / INSPECT / SAFE ISOLATION

  • ↓
  • RELEVANT DEAD TESTS IN REQUIRED ORDER
  • ↓
  • BEFORE ENERGISING THE INSTALLATION

Confirm origin supply polarity and relevant protective measures.

Remove test links; restore and verify connections; reinstate barriers.

  • ↓
  • CONTROLLED ENERGISATION AND APPLICABLE LIVE/FUNCTIONAL CHECKS
  • Determine source/loop/fault-current information appropriately;
  • verify the actual protective measures, RCD and button functions,

maintained phase sequence and applicable equipment operation.

Additional verification depends on the protective measure and installation. The minimum RCD instrument test is AC at IΔn, with the correct general/S-type limits;5× is optional diagnostics. Phase sequence can be verified by dead identification; live rotation checks are used where needed.

Warning

Separate live Ze testing: Where necessary, exclude parallel returns under a safe controlled procedure. Justify live work under all EAWR14 conditions; isolate and secure every source to outgoing circuits, assess diverted current before handling earthing and use suitable GS38/instrument protection and risk-assessed PPE. Restore and verify required earthing before outgoing energisation. Do not leave protective connections disconnected for downstream live testing.

Training Activity 4: Recording and Self-Checking

In the final documentation phase, candidates compile all verified raw data into standard BS 7671 documentation (Electrical Installation Certificate or Electrical Installation Condition Report with accompanying schedules). REVISION SELF-CHECK — NOT AN EAL MARKING RUBRIC

  • Safety: actual isolation boundary, live-work justification and restored protection
  • Measurements: valid method, actual instrument uncertainty and expected circuit data
  • Reasoning: explain ring patterns, IR results and the applicable protection limit
  • Records: current form, relevant numerical results, defined outcomes and attachments

Do not assume a universal±5% assessment tolerance or automatic referral from one listed clerical error. Follow the actual assessment instructions; use the current source and manufacturer data when assessing the result. The 0.8Zs screen has a defined purpose and does not replace every detailed thermal/protection assessment.

Candidate Feedback and Referral Retake

If a candidate is referred on any single task element (for example, miscalculating ring circuit spur values or leaving an inspection box blank):

The assessor provides clear, constructive feedback detailing the exact failure criterion.

The candidate is scheduled for remedial tuition focused on that specific weakness.

The candidate retakes only the referred task element , preserving all other passed elements of Practical 1 and Practical 2.