Study guide
12.2 Circuit Earth Fault Loop Impedance (Zs) Measurement & Calculation
EAL Level 3 Inspection & Testing Awards Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Qualification Overview & Regulatory Framework
1.1 EAL Level 3 Qualification Structure & Examination Specifications 1.2 Statutory Framework & Electricity at Work Regulations 1989 1.3 Non-Statutory Standards: BS 7671:2018+A4:2026 and IET Guidance Note 3
2 Chapter 2: Health, Safety & Safe Isolation Procedures
2.1 Safe Isolation Principles & Step-by-Step Procedure 2.2 Test Equipment Safety & HSE Guidance Note GS38 2.3 Live Working Precautions, Risk Assessment & PPE
3 Chapter 3: Documentation, Certification & Reporting
3.1 Purpose of Initial Verification vs Periodic Inspection 3.2 Electrical Installation Certificates (EIC) & Signatories 3.3 Minor Electrical Installation Works Certificates (MEIWC) 3.4 Electrical Installation Condition Reports (EICR) & Extent/Limitations
4 Chapter 4: Safe Inspection: Supply, Earthing & Intake Equipment
4.1 Visual Inspection Principles & Methodology 4.2 Supply Intake, Metering & Distribution Network Operator Equipment 4.3 Earthing Arrangements & Protective Bonding Conductors
5 Chapter 5: Safe Inspection: Distribution Boards, Circuits & Enclosures
5.1 Distribution Boards & Consumer Units Inspection 5.2 Protective Devices, Switchgear & Coordination 5.3 Wiring Systems, Cable Selection & Installation Methods
6 Chapter 6: Safe Inspection: Routing, Protection & Special Locations
6.1 Cable Concealment, Safe Zones & Mechanical Protection 6.2 External Influences & Enclosure IP Ratings 6.3 Special Installations, Locations & Modern Technologies
7 Chapter 7: Condition Reporting & EICR Classification Coding
7.1 EICR Classification Coding: Code C1 (Danger Present) 7.2 EICR Classification Coding: Code C2 (Potentially Dangerous) 7.3 EICR Classification Coding: Code C3 & Code FI
8 Chapter 8: Safe Testing: Preparation, Sequence & Instruments
8.1 The Prescribed Testing Sequence 8.2 Test Instrument Standards & BS EN 61557 8.3 On-Site Safety Precautions & Client Coordination During Testing
9 Chapter 9: Dead Testing: Continuity of Protective Conductors
9.1 Continuity Testing Method 1 (R1 + R2) 9.2 Continuity Testing Method 2 (R2 Wandering Lead) 9.3 Main Protective Bonding Conductor Continuity
10 Chapter 10: Dead Testing: Continuity of Ring Final Circuits
10.1 Ring Final Circuit Testing: End-to-End Measurements 10.2 Ring Final Circuit Testing: Interconnection & Cross-Connection 10.3 Ring Circuit Fault Diagnosis & Reading Interpretation
11 Chapter 11: Dead Testing: Insulation Resistance & Polarity
11.1 Insulation Resistance Testing Principles & Precautions 11.2 Insulation Resistance Test Voltages & Minimum Values 11.3 Dead Polarity Testing Methods & Verification 11.4 Earth Electrode Resistance Testing
12 Chapter 12: Live Testing: Earth Fault Loop Impedance (Zs & Ze)
12.1 External Earth Fault Loop Impedance (Ze) Measurement 12.2 Circuit Earth Fault Loop Impedance (Zs) Measurement & Calculation 12.3 The 0.8 Temperature Correction Rule & Maximum Permitted Zs 12.4 Prospective Fault Current (PFC / Ipf) Testing
13 Chapter 13: Live Testing: RCDs, Phase Sequence & Functional Tests
13.1 RCD Operating Principles, Characteristics & Types 13.2 RCD Testing Procedures & Maximum Disconnection Times 13.3 Phase Sequence, Voltage Drop & Additional Functional Testing 13.4 Fault Finding & Diagnostic Methodology in Electrical Testing
14 Chapter 14: Commissioning, Handover & Practical Assessment Mastery
14.1 Initial Energisation & Final Commissioning Sequence 14.2 Completing Schedules of Inspections & Schedules of Test Results 14.3 EAL Practical Assessment Structure & Inspection Rig Scenarios 14.4 Common Candidate Errors & Exam Traps
12.2 Circuit Earth Fault Loop Impedance (Zs) Measurement & Calculation
Key Takeaways Explain This Topic AI
Circuit earth fault loop impedance (Zs) represents the complete series impedance of the fault path from the supply transformer secondary winding, through the circuit line conductor to the fault point, returning via the CPC, MET, and external earth path.
Zs may be established by suitable measurement or calculation. For an ordinary predominantly resistive TN circuit, use Ze + (R1 + R2); for TT include the consumer electrode contribution as well as the external supply and circuit paths.
Parallel paths can reduce a live Zs reading compared with a calculation based on the intended CPC. Compare like-for-like results, allowing for temperature, reactance, source changes, instrument uncertainty and RCD uplift.
Investigate an unexplained measured/calculated discrepancy. Check the tester, contacts and test conditions as well as possible circuit defects; a fixed difference alone does not prove a high-resistance joint or a complete pass.
Choose the tester mode for the circuit and RCD arrangement. High-current modes suit appropriate unprotected paths; low-current no-trip modes reduce unwanted tripping but do not guarantee it on every circuit. Follow the instrument accuracy and connection requirements.
Last updated: November 2026
12.2 Circuit Earth Fault Loop Impedance (Zs) Measurement & Calculation
Core Testing Principle: Circuit earth fault loop impedance ( Z s Z_s Z s ) quantifies the total opposition encountered by an earth fault current circulating through an installation circuit. BS 7671 permits Z s Z_s Z s to be established either by direct live testing at the furthest outlet or by adding the measured dead continuity ( R 1 + R 2 ) (R_1 + R_2) ( R 1 + R 2 ) to the external loop impedance ( Z e Z_e Z e ). An unexplained discrepancy needs investigation of both the circuit and the measurement conditions.
The Complete Circuit Earth Fault Loop Path
When a line-to-earth fault of negligible impedance occurs at an electrical accessory or luminaire, fault current circulates through a closed circuit spanning both external distribution assets and internal installation conductors. The total impedance of this complete loop is designated Z s Z_s Z s . THE COMPLETE CIRCUIT FAULT LOOP (Zs)
- ┌────────────────────────────────────────────────────────────────────────┐
- │ 1. Substation Transformer Secondary Winding │
- │ │ │
- │ 2. DNO Service Cable Line Conductor ──────────────────┐ External Path │
- │ │ │ (Ze) │
- │ 3. Cutout Fuse & Consumer Unit Main Switch │ │
- │ │ ▼ │
- │ 4. Circuit Overcurrent Protective Device (MCB / RCBO) │
- │ │ │
- │ 5. Circuit Line Conductor (R1) ───────────────────────┐ Internal Path │
- │ │ │ (R1 + R2) │
- │ ▼ POINT OF FAULT (Short Circuit Line to Metal Chassis) │
- │ │ │ │
- │ 6. Circuit Protective Conductor (R2) ─────────────────┘ │
- │ │ │
- │ 7. Distribution Board Earth Bar │
- │ │ │
- │ 8. Installation Earthing Conductor & Main Earthing Terminal (MET) │
- │ │ │
- │ 9. DNO Earth Return Path (Lead Sheath / PEN / Earth Mass) │
- │ │ │
- │ 10. Substation Neutral Star Point (Loop Closes at Source) │
- └────────────────────────────────────────────────────────────────────────┘
- The Fundamental Calculation Formula
Under BS 7671 Regulation 643.7.3 and IET Guidance Note 3, the familiar calculation for an ordinary predominantly resistive TN circuit is:
Z s = Z e + ( R 1 + R 2 ) Z_s = Z_e + (R_1 + R_2) Z s = Z e + ( R 1 + R 2 )
Where:
Z s Z_s Z s : Total circuit earth fault loop impedance (Ω). For TT, include the consumer electrode as well as the externally defined Z e Z_e Z e and internal circuit paths; the TN expression below must not omit it.
Z e Z_e Z e : External earth fault loop impedance determined for the supply by an appropriate method (Ω).
( R 1 + R 2 ) (R_1+R_2) ( R 1 + R 2 ) : Relevant dead continuity resistance of the circuit line and CPC to the point assessed. For a small, predominantly resistive circuit this is the familiar calculation; account for temperature and significant reactance where relevant.
The Two BS 7671 Accepted Methods of Determining Z s Z_s Z s
BS 7671 authorizes inspectors to establish Z s Z_s Z s for every circuit using either of two recognized approaches:
Method 1: Direct Live Measurement
Where live measurement is justified, use a suitable loop tester complying with BS EN 61557-3 or providing equivalent performance/safety, with the required protective connections in service:
Standard Socket Outlets: The loop tester is plugged in using an approved 13 A socket test lead featuring a standard BS 1363 3-pin plug.
Luminaires and fixed equipment: Use the instrument-approved two- or three-lead connection at the relevant point, with suitable live-work controls. Connect neutral where that test mode requires it.
Operational Advantage: Measures the true impedance under real operating voltage ( 230 V 230\text{ V} 230 V ), automatically incorporating all parallel metallic paths (structural steel, conduit, shared CPCs).
Method 2: Calculation Method ( Z s = Z e + ( R 1 + R 2 ) Z_s = Z_e + (R_1 + R_2) Z s = Z e + ( R 1 + R 2 ) )
The inspector calculates Z s Z_s Z s mathematically by adding the dead continuity test result ( R 1 + R 2 ) (R_1 + R_2) ( R 1 + R 2 ) obtained during dead testing (as recorded on the Schedule of Test Results) to the appropriately determined external loop impedance ( Z e Z_e Z e ):
Calculated Z s = Z e + ( R 1 + R 2 ) \text{Calculated } Z_s = Z_e + (R_1 + R_2) Calculated Z s = Z e + ( R 1 + R 2 )
Operational Advantage: Eliminates the safety hazard of conducting live tests at remote, elevated, or wet locations (e.g. external floodlights, swimming pool pump rooms, industrial process plants). Furthermore, it avoids nuisance tripping of upstream RCDs and eliminates reading instability caused by network noise.
Comparing Measured and Calculated Z s Z_s Z s
The calculation Z e + ( R 1 + R 2 ) Z_e+(R_1+R_2) Z e + ( R 1 + R 2 ) is especially useful for small circuits where resistance dominates. A live result may be lower because current also returns through parallel CPCs, metallic containment or bonded paths. That does not remove the need to verify the intended protective conductor.
Compare the same point and protection arrangement. Temperature, a changed supply value, conductor reactance, test-lead/contact resistance, instrument uncertainty, electrical noise and RCD uplift can affect the results. A difference is evidence to assess, not proof of a particular defect.
Result Assessment
Measured value lower Check whether parallel paths or test conditions explain it; retain independent continuity evidence.
Values close Consistent results support the assessment but do not prove every termination flawless.
Measured value unexpectedly higher Check mode, contacts, repeatability, source/temperature conditions and the actual circuit. Investigate a possible high-resistance connection and take protective action where danger is identified.
Use the applicable protective-device limit and its temperature basis for acceptance. There is no universal 0.03 Ω or 0.10 Ω difference that certifies or condemns every circuit.
No-Trip Testing Technology & Modern Test Instruments
Choose a mode and connection approved by the instrument manufacturer for the supply and RCD arrangement. Actual current, duration, range and accuracy depend on the tester; display resolution is not the same as measurement accuracy. HIGH-CURRENT LOOP MODE LOW-CURRENT / NO-TRIP MODE
- Typical purpose: suitable Typical purpose: RCD-protected
- non-RCD-protected test path circuit without intentional tripping
- Greater test signal Smaller signal; noise/contact effects matter
- Can trip an upstream RCD Existing leakage or unsuitable conditions
- can still cause a trip
Use the specified leads, voltage/category rating and operating range.
High-Current Testing
The tester applies a controlled load and determines loop impedance from its measurement of the supply response. Familiar instruments offer high-current modes such as 6 A or 25 A, but these are product specifications, not universal BS 7671 parameters. Do not use a high-current L–E mode through an RCD where it would cause an unwanted trip or unsafe test condition. A test current is not a repair method for oxidised or defective terminals.
Low-Current No-Trip Testing
A suitable no-trip mode limits the residual test current or uses the manufacturer’s measurement method to reduce RCD operation. The familiar 30 mA RCD non-operating point is 0.5IΔn=15 mA under the specified product test conditions; existing leakage and circuit conditions still matter. Select a mode suitable for the actual RCD type. Some instruments offer two-wire and three-wire arrangements; use the prescribed connections rather than assuming one universal circuit or DC-saturation mechanism.
Investigating Unstable Readings
Check leads, contact quality, range and repeatability first. Electronic loads, switching, generation and RCD uplift can affect a low-current measurement. Follow the tester's noise indication and instructions, and coordinate any necessary load isolation. Do not simply disconnect every electronic load regardless of the test conditions or accept an unexplained odd reading. A properly established calculation can avoid unnecessary remote live testing; it still needs valid source and continuity information and the appropriate protection assessment.