Study guide
1.1 EAL Level 3 Qualification Structure & Examination Specifications
EAL Level 3 Inspection & Testing Awards Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Qualification Overview & Regulatory Framework
1.1 EAL Level 3 Qualification Structure & Examination Specifications 1.2 Statutory Framework & Electricity at Work Regulations 1989 1.3 Non-Statutory Standards: BS 7671:2018+A4:2026 and IET Guidance Note 3
2 Chapter 2: Health, Safety & Safe Isolation Procedures
2.1 Safe Isolation Principles & Step-by-Step Procedure 2.2 Test Equipment Safety & HSE Guidance Note GS38 2.3 Live Working Precautions, Risk Assessment & PPE
3 Chapter 3: Documentation, Certification & Reporting
3.1 Purpose of Initial Verification vs Periodic Inspection 3.2 Electrical Installation Certificates (EIC) & Signatories 3.3 Minor Electrical Installation Works Certificates (MEIWC) 3.4 Electrical Installation Condition Reports (EICR) & Extent/Limitations
4 Chapter 4: Safe Inspection: Supply, Earthing & Intake Equipment
4.1 Visual Inspection Principles & Methodology 4.2 Supply Intake, Metering & Distribution Network Operator Equipment 4.3 Earthing Arrangements & Protective Bonding Conductors
5 Chapter 5: Safe Inspection: Distribution Boards, Circuits & Enclosures
5.1 Distribution Boards & Consumer Units Inspection 5.2 Protective Devices, Switchgear & Coordination 5.3 Wiring Systems, Cable Selection & Installation Methods
6 Chapter 6: Safe Inspection: Routing, Protection & Special Locations
6.1 Cable Concealment, Safe Zones & Mechanical Protection 6.2 External Influences & Enclosure IP Ratings 6.3 Special Installations, Locations & Modern Technologies
7 Chapter 7: Condition Reporting & EICR Classification Coding
7.1 EICR Classification Coding: Code C1 (Danger Present) 7.2 EICR Classification Coding: Code C2 (Potentially Dangerous) 7.3 EICR Classification Coding: Code C3 & Code FI
8 Chapter 8: Safe Testing: Preparation, Sequence & Instruments
8.1 The Prescribed Testing Sequence 8.2 Test Instrument Standards & BS EN 61557 8.3 On-Site Safety Precautions & Client Coordination During Testing
9 Chapter 9: Dead Testing: Continuity of Protective Conductors
9.1 Continuity Testing Method 1 (R1 + R2) 9.2 Continuity Testing Method 2 (R2 Wandering Lead) 9.3 Main Protective Bonding Conductor Continuity
10 Chapter 10: Dead Testing: Continuity of Ring Final Circuits
10.1 Ring Final Circuit Testing: End-to-End Measurements 10.2 Ring Final Circuit Testing: Interconnection & Cross-Connection 10.3 Ring Circuit Fault Diagnosis & Reading Interpretation
11 Chapter 11: Dead Testing: Insulation Resistance & Polarity
11.1 Insulation Resistance Testing Principles & Precautions 11.2 Insulation Resistance Test Voltages & Minimum Values 11.3 Dead Polarity Testing Methods & Verification 11.4 Earth Electrode Resistance Testing
12 Chapter 12: Live Testing: Earth Fault Loop Impedance (Zs & Ze)
12.1 External Earth Fault Loop Impedance (Ze) Measurement 12.2 Circuit Earth Fault Loop Impedance (Zs) Measurement & Calculation 12.3 The 0.8 Temperature Correction Rule & Maximum Permitted Zs 12.4 Prospective Fault Current (PFC / Ipf) Testing
13 Chapter 13: Live Testing: RCDs, Phase Sequence & Functional Tests
13.1 RCD Operating Principles, Characteristics & Types 13.2 RCD Testing Procedures & Maximum Disconnection Times 13.3 Phase Sequence, Voltage Drop & Additional Functional Testing 13.4 Fault Finding & Diagnostic Methodology in Electrical Testing
14 Chapter 14: Commissioning, Handover & Practical Assessment Mastery
14.1 Initial Energisation & Final Commissioning Sequence 14.2 Completing Schedules of Inspections & Schedules of Test Results 14.3 EAL Practical Assessment Structure & Inspection Rig Scenarios 14.4 Common Candidate Errors & Exam Traps
1.1 EAL Level 3 Qualification Structure & Examination Specifications
Key Takeaways Explain This Topic AI
EAL provides three primary Level 3 inspection and testing pathways: the combined award (603/2625/6; GLH 45, TQT 50), the standalone initial verification award (600/4337/4; GLH 36, TQT 46), and the standalone periodic inspection award (600/4338/6; GLH 37, TQT 51).
The combined 603/2625/6 on-screen examination (Unit ITC3/001) comprises 60 multiple-choice questions over 120 minutes with a nominal pass threshold of 61.5% (approx. 37 correct).
For the periodic award, the bridging exam is waived only with a recognized Level 3 initial-verification qualification and sufficient current understanding. QCR/001 is 60 minutes at 62.5%; the specification conflicts on its 25/35-question count.
EAL's open-book rules permit bookmarks, tabs, highlighting, short handwritten cross-references to other parts of the publication, and official corrigenda; added sample questions, answers, diagrams, formulae and detailed notes are prohibited.
The EAS Qualifications Guide lists EAL inspection and testing awards alongside City & Guilds 2391 awards as accepted qualifications for the relevant work. Qualified Supervisor acceptance also requires appropriate core competence, experience, continuing professional development and assessment by the certification or registration body.
Last updated: November 2026
1.1 EAL Level 3 Qualification Structure & Examination Specifications
Core Principle: In the UK electrotechnical sector, demonstrating competence in inspection, testing, and condition reporting is mandatory for verifying statutory compliance under the Electricity at Work Regulations 1989 and technical safety under BS 7671:2018+A4:2026. The Excellence, Achievement & Learning (EAL) Level 3 awards assess inspection and testing knowledge and practical skills.
The Inspection & Testing Landscape in the UK Electrotechnical Sector
Inspection and testing represent the ultimate barrier against electrical shock, thermal burns, electrical fires, and equipment destruction. Every electrical installation—whether a new domestic consumer unit upgrade, a high-voltage commercial distribution network, or an industrial processing plant—must be comprehensively inspected and tested before being energized and put into service, and periodically re-examined throughout its operating lifetime.
Awarding organisations across the United Kingdom structure their qualifications around two distinct disciplines:
Initial Verification: The process of verifying that new installation work, additions, or alterations comply fully with BS 7671:2018+A4:2026, have been erected correctly in accordance with manufacturer instructions, and are safe to put into service without risk of injury or fire.
Periodic Inspection and Condition Reporting: The detailed engineering evaluation of an existing electrical installation to determine whether it remains safe for continued service, identifying deterioration, defects, damage, and dangerous conditions against current national safety benchmarks.
EAL (Excellence, Achievement & Learning Ltd) is an approved national awarding organisation recognized by Ofqual in England, Qualifications Wales, and the CCEA in Northern Ireland. EAL's inspection and testing qualifications are designed around the technical requirements of BS 7671 and IET Guidance Note 3 (GN3) .
The Three EAL Level 3 Qualification Pathways
EAL delivers three tailored qualifications to serve different electrotechnical career trajectories, ranging from standalone initial commissioning to comprehensive commercial condition reporting:
EAL Qualification Portfolio Comparison
Qualification Title Ofqual / EAL QN Unit Code(s) Target Scope Guided Learning Hours (GLH) Total Qualification Time (TQT) Practical Assessments
EAL Level 3 Award in Electrical Installation Inspection, Testing, Certification and Reporting 603/2625/6 ITC3/001 Combined Initial Verification and Periodic Inspection 45 Hours 50 Hours 2 Practical Tasks (Inspection + Testing/Reporting)
EAL Level 3 Award in the Initial Verification and Certification of Electrical Installations 600/4337/4 QIT3/001 Initial Verification of new installations and additions only 36 Hours 46 Hours 2 Practical Tasks (Inspection + Testing/Reporting)
EAL Level 3 Award in the Periodic Inspection, Testing and Certification of Electrical Installations 600/4338/6 QCRB/001 & QCR/001 Periodic inspection, testing, and EICR reporting on existing systems 37 Hours 51 Hours 2 Practical Tasks (Inspection + Testing/Reporting)
1. The Combined Award (603/2625/6)
The EAL Level 3 Award in Electrical Installation Inspection, Testing, Certification and Reporting (603/2625/6) is the flagship qualification. It unites the entire curriculum of both initial verification and periodic condition reporting into a single consolidated course of study (Unit ITC3/001). Under EAL Specification Issue 5 (Section 3), the qualification is structured with 45 Guided Learning Hours (GLH) and 50 Total Qualification Time (TQT) hours. This award is primarily selected by practicing electricians, site supervisors, electrical contractors, and maintenance engineers seeking comprehensive authority across residential, commercial, and industrial facilities.
2. Standalone Initial Verification (600/4337/4)
The 600/4337/4 award is dedicated exclusively to initial verification (Unit QIT3/001). Candidates focus purely on new installations, circuit extensions, minor works, and initial commissioning. It excludes the condition assessment codes (C1, C2, C3, FI) associated with Electrical Installation Condition Reports (EICRs). EAL Specification Issue 5 defines this award as requiring 36 GLH and 46 TQT hours. It is suitable for practicing electricians who concentrate on new build installations or additions.
3. Standalone Periodic Inspection (600/4338/6)
The 600/4338/6 award is tailored for experienced operatives who inspect and report on existing electrical systems, requiring 37 GLH and 51 TQT hours. The bridging-exam exemption requires a recognized Level 3 initial-verification qualification and sufficient current understanding of its learning outcomes . Qualifying candidates take the periodic QCR/001 exam and practical assessments. Other candidates must pass the QCRB/001 bridging component before progressing to QCR/001. This exemption does not replace the award’s Level 3 electrotechnical entry requirements.
EAS Recognition and Qualified Supervisor Requirements
The Electrotechnical Assessment Specification (EAS) sets minimum requirements used by certification and registration bodies when assessing electrical enterprises. The EAS Qualifications Guide lists accepted qualifications for particular work categories. It does not make one short-course award a complete route to Qualified Supervisor (QS) status.
Accepted Inspection and Testing Qualifications
EAL 603/2625/6 and City & Guilds 2391-52 appear in the initial verification and periodic inspection tables.
EAL 600/4337/4 and City & Guilds 2391-50 appear in the initial verification table.
EAL 600/4338/6 and City & Guilds 2391-51 appear in the periodic inspection table.
These are accepted alternatives for those inspection and testing requirements; their assessment structures differ.
What Else a QS Applicant Needs
The applicable EAS work category also requires underpinning electrotechnical competence and the relevant qualifications. A QS applicant needs at least two years' evidence of responsibility for the technical standard of electrotechnical work, ongoing continuing professional development, and acceptance by the certification or registration body.
A QS has day-to-day responsibility for the safety, quality and technical standard of the enterprise's work and for accurate verification records. Holding an inspection and testing award alone does not confer QS status, scheme registration or unrestricted authority to certify other people's work.
On-Screen Examination Specifications & Parameters
The theoretical knowledge component of each EAL qualification is assessed via an externally set, on-screen multiple-choice examination delivered at an approved EAL assessment centre.
Examination Format & Performance Benchmarks
Specification Parameter Combined Award (603/2625/6) Standalone Initial (600/4337/4) Standalone Periodic Bridging Exam Standalone Periodic Standard Exam
Unit Reference ITC3/001 QIT3/001 QCRB/001 QCR/001
Target Candidate Combined candidates Initial verification candidates Periodic candidates without the bridging exemption All periodic candidates
Question Count 60 Multiple-Choice Questions 55 Multiple-Choice Questions 35 Multiple-Choice Questions 35 Questions (Appendix 2) / 25 Questions (Section 6.1 table)
Time Limit 120 Minutes (2.0 Hours) 90 Minutes (1.5 Hours) 60 Minutes (1.0 Hour) 60 Minutes (1.0 Hour)
Pacing Allocation 2.0 minutes per question ~1.64 minutes per question ~1.71 minutes per question ~1.71 minutes per question (if 35 Qs)
Nominal Pass Threshold 61.5% 62.0% 63.0% 62.5%
Exam Delivery Mechanism Secure On-Screen Computer Based Secure On-Screen Computer Based Secure On-Screen Computer Based Secure On-Screen Computer Based
Permitted Book Status Open Book (IET GN3 only) Open Book (IET GN3 only) Open Book (IET GN3 only) Open Book (IET GN3 only)
Warning
Specification Discrepancy Disclosure: Unit QCR/001 Question Count
Candidates and assessment centres should note an internal discrepancy within official EAL Qualification Specification Issue 5:
Section 6.1 Summary Table: Lists Unit QCR/001 as comprising 25 questions with a 60-minute time limit.
Appendix 2 (Detailed Examination Specifications): Lists Unit QCR/001 as comprising 35 questions with a 60-minute time limit and a 62.5% pass threshold.
To ensure pacing readiness, candidates should prepare for the higher demand scenario of 35 questions in 60 minutes , which equates to approximately 1.71 minutes per question , rather than assuming the more relaxed 2.4 minutes per question implied by a 25-question format.
Open-Book Examination Regulations & Permitted Reference Notes
EAL operates specific open-book examination regulations set out in Section 6.1 of the Qualification Specification to ensure fair and rigorous assessment across all accredited centres:
Important
Permitted Reference Material: IET Guidance Note 3 (GN3)
EAL names IET Guidance Note 3: Inspection & Testing as the permitted examination reference but does not name an edition in its public specification. Confirm the accepted edition with the centre. This guide teaches the current BS 7671:2018+A4:2026 requirements.
Permitted Annotations and Additions:
Bookmarks and page tabs: Dividing tabs and adhesive flags used to mark key sections, chapters, and tables.
Highlighting: Standard highlighter pens applied to text or tables within the book.
Short cross-reference notes: Brief handwritten notes that reference other parts of the document (e.g., noting a relevant regulation number, appendix, or table cross-reference).
Official corrigenda and amendments: Errata slips or official amendment sheets published by the IET or BSI.
Strictly Prohibited Annotations and Materials:
Sample examination questions, mock questions, or practice answers.
Detailed technical notation, explanations, or crib summaries.
Diagrams, sketches, or flowcharts added by hand.
Mathematical formulae or calculation shortcuts written into margins or blank pages.
Any loose sheets, inserts, or supplementary materials not officially issued by the IET/BSI.
Any content that could provide an unfair advantage to the learner.
Permitted Calculating Equipment:
A standard, non-programmable scientific calculator.
Strictly Prohibited Equipment:
Programmable graphing calculators, smartphones, smartwatches, digital tablets, cameras, internet-enabled wearables, and any unapproved external reference books (such as BS 7671 itself or the On-Site Guide, unless an individual centre unit explicitly specifies otherwise).
Centres must check that reference materials do not give an unfair advantage. EAL requires clean copies to be available where a book’s suitability is unclear. Resolve doubtful additions with the centre before the examination and follow its examination instructions.
Practical Assessments and Original Practice Activities
Passing the on-screen exam is only one requirement. EAL Specification section 6.1 lists two practical assessments for each award:
600/4337/4: Initial Inspection Assessment and Initial Verification Assessment.
600/4338/6 and 603/2625/6: Periodic Inspection Assessment and Periodic Inspection and Testing Assessment.
EAL sets these assessments and the centre marks them, subject to internal standardisation and external quality assurance. Learners must pass all associated assessments. The assessment instructions and resource requirements are supplied in EAL's assessment documentation; the public specification does not establish a universal rig layout, fault count or task duration.
Original Practice Activities
Use a separate training installation to practise systematic visual inspection of supply equipment, earthing and bonding, enclosures, protective devices, wiring and accessories. Explain each observed defect and, for periodic work, justify its classification from the actual danger. These are study activities, not a published EAL fault list.
Practise safe isolation, protective-conductor and ring continuity, insulation resistance, polarity, and the applicable supply, loop, RCD and functional checks. Decide which measurements are necessary, protect connected equipment, and record actual results on appropriate certificates or reports and their schedules. Use the worked sections of this guide to interpret results and justify safe next steps.
EAL section 6.3 requires formal assessment rigs to be kept secure and used only for recorded assessments, not prior training.
Reassessment
A learner referred in a practical assessment retakes only the referred task element, after feedback and appropriate tuition. An on-screen exam failure may be resat after feedback and tuition, subject to EAL's current charges.
Examination Strategy & Time Management in Guidance Note 3
With 60 questions in 120 minutes on the 603/2625/6 exam, pacing is vital. Successful candidates adopt structured navigation methods:
Do Not Treat the Exam as a Reading Test: Attempting to look up all 60 questions in Guidance Note 3 guarantees running out of time. Candidates must possess instant recall of statutory law, basic testing sequences, instrument standards, and standard safety formulas.
Targeted GN3 Lookup: Reserve the book for specific tabulated values (such as maximum permitted earth fault loop impedance tables in Appendix B, minimum insulation resistance thresholds in the current edition's tables, or specific testing voltage tolerances).
Strategic Tab Placement: Use the contents and index of your permitted GN3 edition to locate:
- The initial verification sequence and individual test methods
- Periodic inspection, limitations and condition reporting
- Insulation resistance test voltages and minimum values
- Maximum earth fault loop impedance values and temperature correction
- Model certificates, reports and schedules
Check the publisher's errata and practise locating these topics before the exam; section and table numbers change between editions.