Study guide
8.4 Parking, Securing & Transporting MEWPs, and Other Site Hazards
IPAF MEWP Operator PAL Card
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: The IPAF MEWP Operator Course & PAL Card
1.1 The IPAF MEWP Operator Course, Theory Test & PAL Card
2 Chapter 2: UK Health, Safety & Statutory Regulations
2.1 Health and Safety at Work etc. Act 1974 (HASAWA) 2.2 Lifting Operations and Lifting Equipment Regulations 1998 (LOLER) 2.3 Provision and Use of Work Equipment Regulations 1998 (PUWER) 2.4 Work at Height Regulations 2005 (WAHR) & Hierarchy of Control
3 Chapter 3: British Standards, Design Classifications & Kinematics
3.1 BS 8460:2025 Code of Practice & the User's Responsibilities 3.2 BS EN 280-1 & ISO 16368 Design Groups (A and B) 3.3 Travel Types (Type 1, Type 2, Type 3) & IPAF Categories
4 Chapter 4: MEWP Categories, Machine Selection & Specifications
4.1 Static Platforms: Category 1a (Static Vertical) and Category 1b (Static Boom) 4.2 Mobile Platforms: Category 3a (Mobile Vertical) and Category 3b (Mobile Boom) 4.3 IPAF Categories, PAVs, Specialist Units & MEWP Selection
5 Chapter 5: Pre-Use Inspections & Daily Maintenance
5.1 Walk-Around Visual Inspection Protocol 5.2 Running Gear, Wheels & Tyre Management 5.3 Documentation, Operator Manuals & Daily Logbook Records
6 Chapter 6: Safety Systems, Controls & Emergency Lowering
6.1 Dual Control Station Operation & Interlocks 6.2 Load Sensing, Tilt Alarms & Anti-Entrapment Devices 6.3 Emergency Descent Systems & Defect Quarantine
7 Chapter 7: Ground Assessment, Outriggers & Stability Physics
7.1 Ground Bearing Capacity & Subsurface Hazards 7.2 Spreader Plates, Outrigger Mats & Setup 7.3 Platform Loading, Centre of Gravity & Dynamic Forces
8 Chapter 8: Environmental Hazards, Overhead Clearances & Safe Operations
8.1 Wind Speed Dynamics & Adverse Weather 8.2 Overhead Power Lines & HSE GS6 8.3 Manoeuvring, Travelling & Collision Avoidance 8.4 Parking, Securing & Transporting MEWPs, and Other Site Hazards
9 Chapter 9: Fall Protection, Catapult Effect & Emergency Rescue
9.1 Fall Protection Policy & IPAF Technical Guidance H1 9.2 PFPE Inspection, Anchor Points & Catapult Physics 9.3 Recovery & Rescue Planning and Suspension Trauma
8.4 Parking, Securing & Transporting MEWPs, and Other Site Hazards
Key Takeaways Explain This Topic AI
At the end of work, lower and stow the platform, park on firm level ground clear of traffic routes and exits, and remove the keys.
ISO 18878 requires operator training to cover securing the MEWP against unauthorised use, transport, hazardous locations and high-pressure systems.
Lead-acid batteries give off hydrogen while charging, so charge only in ventilated areas away from sparks and flames.
IPAF notes that a vehicle-mounted MEWP over 3.5 tonnes must, as a general rule, be driven by a person holding an HGV licence.
In explosive atmospheres zoned under DSEAR 2002, only a MEWP certified for that zone may be used.
Last updated: October 2026
Parking, Securing & Transporting MEWPs, and Other Site Hazards
Quick Answer: At the end of work, lower and stow the platform , park on firm, level ground clear of traffic routes, exits and overhead hazards, remove the keys and secure the machine against unauthorised use —an ISO 18878 training requirement. Charge batteries only in ventilated areas because they give off hydrogen. Loading, unloading and road transport are separate skills: IPAF runs a Loading and Unloading (LOAD) course, and vehicle-mounted MEWPs over 3.5 tonnes generally need an HGV-licensed driver. Finally, plan for the hazards that the main chapters do not cover in detail: flammable atmospheres , exhaust fumes and confined spaces , high-pressure systems , falling objects , hot work and work near water .
ISO 18878:2025 lists several topics that every MEWP operator's theory training must include but that are easy to overlook: issues associated with transporting a MEWP, understanding that the MEWP must be secured against unauthorised use, hazardous locations (flammable or explosive atmospheres) and hazards associated with high-pressure systems. This section brings them together.
Parking and Making the MEWP Safe at the End of Work
A MEWP left elevated, unlocked or parked in the wrong place is a hazard to everyone on site. At the end of each task or shift:
Lower and stow : Fully lower the platform, retract booms and extensions, and stow outriggers as the manual requires. Never leave a MEWP elevated and unattended.
Choose the parking spot : Park on firm, level ground, away from excavations, traffic routes, fire exits, doorways, overhead cables and areas where other plant will work. Indoors, do not block escape routes or sprinkler and alarm equipment.
Secure the machine : Apply the parking brake (or wheel brakes on a PAV), switch off, and remove the ignition and selector keys . Store keys where only authorised operators can get them. Where a battery isolator or lockable compound is provided, use it.
Record : Report any defect found during the shift, and record your operating experience in your ePAL log book.
Warning
Keys left in a parked MEWP invite unauthorised use by untrained people. Securing the machine is part of the operator's job, and ISO 18878 requires operators to understand it.
Charging and Refuelling
Battery charging : Lead-acid batteries give off hydrogen while charging. Charge only in a well-ventilated area designated for the purpose, away from sparks, flames and smoking, with the battery trays open if the manufacturer requires it. Electrolyte is corrosive, so wear the PPE the manufacturer specifies when checking levels.
Refuelling : Refuel with the engine off and the platform stowed, away from ignition sources, using the correct fuel. Clean up spills before restarting.
Loading, Unloading and Road Transport
Loading a MEWP onto a vehicle or trailer is a common point for overturns and runaways. Operators who load and unload need specific training; IPAF runs a separate Loading and Unloading (LOAD) course for delivery drivers.
- Task Key controls
- Choosing the area Firm, level ground away from traffic and pedestrians; good lighting
Ramps and beavertails Check the ramps are rated for the machine's weight, correctly fitted and not slippery; travel slowly in the stowed position, within the manufacturer's slope rating and orientation
Securing the load Use the manufacturer's tie-down points and suitable lashings; never ride in the platform during loading
Driving the vehicle IPAF notes that, as a general rule, a vehicle-mounted MEWP over 3.5 tonnes must be driven by a person with an HGV licence; vehicles over 3 m high need a travel-height notice in the cab
Weights and permits IPAF and the UK government publish guidance on machine weights, permissible loads and engineering-plant rules for MEWPs used on the road
- Other Site Hazards to Plan For
- Hazardous Locations
In refineries, chemical plants, paint shops and some food and pharmaceutical sites, flammable gases, vapours or dusts can create explosive atmospheres. Under the Dangerous Substances and Explosive Atmospheres Regulations 2002 (DSEAR) , these areas are zoned, and only equipment certified for the zone may be used. A standard MEWP is an ignition source; use only a machine specified for that zone (Section 4.3) and follow the site permit system.
Exhaust Fumes and Confined or Enclosed Spaces
Diesel and LPG engines produce carbon monoxide and other fumes. Indoors, in basements, tunnels or poorly ventilated buildings, use electric machines or provide ventilation and monitoring as the risk assessment requires. BS 8460:2025 adds guidance on confined spaces, where rescue is also harder to plan.
High-Pressure Systems
MEWP hydraulic systems run at very high pressure. A pinhole leak can inject oil through the skin, so never search for leaks with your hand —use card or wood, and get urgent medical help for any injection injury. Hydraulic components can hold pressure after shutdown; leave repairs to competent technicians. Treat tyres, accumulators and gas struts with the same respect.
Falling Objects
Dropped tools and materials are a hazard to people below. Keep the platform tidy, tether tools when working over people, keep materials inside the platform, never throw anything from the platform, and keep the exclusion zone in place (Section 8.3).
Hot Work
Welding, cutting and grinding from a platform can damage hydraulic hoses, harness webbing and lanyards, and start fires. Hot work needs a permit, protection for the machine and PPE, a suitable fire extinguisher, and a fire watch as the site requires.
Water, Exiting at Height and Other Special Cases
Working next to or over water needs a decision on life jackets versus harnesses (Section 9.1), and exiting the platform at height is not allowed unless a rigorous risk assessment shows it is the safest method (Section 9.3).