Study guide
11.2 GS38 Equipment, Earthing, RCDs & Electric Shock Rescue
JIB ECS Health, Safety & Environmental Assessment Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Assessment Overview
About the ECS Health, Safety & Environmental Assessment
2 Chapter 1: General Health and Safety Legislation & Management
1.1 The Health and Safety at Work etc. Act 1974 & Statutory Duties 1.2 Risk Assessment, Hierarchy of Controls & CDM 2015 Regulations 1.3 Safety Signs, Workplace Inspections & Reporting Unsafe Conditions
3 Chapter 2: Manual Handling Operations & Ergonomics
2.1 Manual Handling Operations Regulations 1992 & Ergonomics 2.2 The TILE Assessment Framework & Kinetic Lifting Techniques
4 Chapter 3: Accident Reporting (RIDDOR) & First Aid Provisions
3.1 RIDDOR 2013 Statutory Reporting Requirements 3.2 Site First Aid Provisions, Accident Recording & Near-Miss Reporting
5 Chapter 4: Personal Protective Equipment at Work
4.1 Personal Protective Equipment at Work Regulations & Legal Framework 4.2 PPE Selection, Standards & Respiratory Protection
6 Chapter 5: Occupational Health, Hygiene & Site Welfare
5.1 Control of Substances Hazardous to Health (COSHH) & Hazardous Materials 5.2 Noise, Hand-Arm Vibration & CDM Welfare Facilities
7 Chapter 6: Fire Safety Fundamentals & Emergency Procedures
6.1 Fire Science, Classification of Fires & Hot Work Protocols 6.2 Portable Fire Extinguishers, Emergency Alarms & Evacuation 6.3 First Aid Response After an Accident on Site
8 Chapter 7: Fire Safety in Buildings, Compartmentation & Fire-Stopping
7.1 Passive Fire Protection, Building Compartmentation & Fire Doors 7.2 Cable Penetration Sealing & Fire-Stopping Integrity 7.3 Higher-Risk Buildings, Holistic Fire Safety & Installer Competence
9 Chapter 8: Working at Height & Access Equipment
8.1 Work at Height Regulations 2005 & Fall Protection Hierarchy 8.2 Ladders, Mobile Access Towers & MEWP Safety 8.3 Scaffolds, Inspections, Harnesses & Protecting People Below
10 Chapter 9: Work Equipment Safety (PUWER) & Lifting Operations (LOLER)
9.1 PUWER 1998 Regulations & 110V Reduced Low Voltage Tool Safety 9.2 LOLER 1998 & Safe Lifting Operations 9.3 Extension Leads, Hand Lamps & Defective Tools on Site
11 Chapter 10: Special Site Hazards (Asbestos, Confined Spaces & Ground Services)
10.1 Asbestos Awareness, Health Risks & Discovery Protocols 10.2 Confined Spaces & Avoiding Underground and Overhead Services 10.3 Site Traffic, Young Workers, Lone Working & Permits to Work
12 Chapter 11: Electrotechnical Safety & The Safe Isolation Procedure
11.1 Electricity at Work Regulations 1989 & Safe Isolation Procedure 11.2 GS38 Equipment, Earthing, RCDs & Electric Shock Rescue 11.3 Optical Fibre Safety, Electrical Permits & Site Installations
13 Chapter 12: Environmental Awareness, Waste Management & Pollution Control
12.1 Waste Duty of Care & The Waste Hierarchy 12.2 Hazardous Waste, Pollution Prevention & Site Sustainability
11.2 GS38 Equipment, Earthing, RCDs & Electric Shock Rescue
Key Takeaways Explain This Topic AI
HSE Guidance Note GS38 calls for probe tips with no more than 4 mm of exposed metal (preferably 2 mm or spring-retractable), finger barriers, HBC fuses of usually no more than 500 mA or current-limiting resistors, and well-insulated leads.
Standard multimeters, neon screwdrivers and non-contact volt sticks must not be used to prove dead, because of wrong-range faults, false readings and screening limitations.
BS 7671 achieves Automatic Disconnection of Supply (ADS) by combining earthing conductors, main protective bonding of extraneous metalwork to the MET, and automatic disconnect devices like MCBs and RCDs.
RCDs giving additional protection (for example on socket-outlets up to 32 A) have a rated residual operating current of 30 mA; a general-type RCD must trip within 300 ms at its rated current.
A few milliamps can be felt, around 10–20 mA can stop you letting go, and from about 30 mA a shock can stop breathing or the heart, so rescue means isolate first, then CPR (30:2) and an AED.
Last updated: October 2026
11.2 GS38 Equipment, Earthing, RCDs & Electric Shock Rescue
Working safely on electrotechnical systems requires approved voltage detection instruments, robust earthing and bonding systems, sensitive protective devices, and decisive emergency rescue protocols. Governed by HSE Guidance Note GS38 and BS 7671 (the IET Wiring Regulations, currently BS 7671:2018+A4:2026, with the A3:2024 version valid until 15 October 2026), these measures protect operatives from fatal electric shock, severe burns, and arc-flash explosions.
HSE Guidance Note GS38: Voltage Test Equipment
HSE Guidance Note GS38 specifies design standards for electrical test equipment used on low-voltage installations (up to 1000V AC) to prevent electric shock, arcing, and flashover.
Mandatory GS38 Probe & Lead Specifications
Exposed Probe Tips : Exposed metal must not exceed 4 mm (maximum), with 2 mm or retractable spring-loaded shrouds recommended to prevent short circuits between adjacent terminals or busbars.
Finger Barriers : Probes must feature moulded finger barriers preventing hands from slipping onto energized tips.
Fuses or Resistors : The probes or leads should incorporate high breaking capacity (HBC) fuses with a low current rating (usually not exceeding 500 mA ), or current-limiting resistors, to protect against short-circuit faults.
Flexible Test Leads : Leads must be adequately insulated and flexible; many have a contrasting inner layer that shows when the outer insulation is cut or worn.
Shrouded Connectors : Terminal plugs must be deeply shrouded and recessed to prevent touch contact if partially detached.
Prohibited Equipment for Proving Dead
The electrotechnical industry strictly prohibits these tools for proving dead:
Multimeters (Digital or Analogue) : Selectable ranges introduce catastrophic error. Selecting resistance ( Ω \Omega Ω ) or current ( A / mA A/\text{mA} A / mA ) creates a dead short across live conductors. They are not fail-safe.
Neon Screwdrivers (Phase Testers) : Neon testers rely on current flowing through the user to Earth. Insulating footwear, dry floors, or broken internal resistors cause false dead readings on live circuits. Their brittle casings easily shatter.
Non-Contact Voltage Detectors (Volt Sticks) : Volt sticks detect electrostatic fields only. They cannot detect shielded conductors, Steel Wire Armoured (SWA) cables, or circuits in metal conduit, and are prone to false negatives from low battery power.
BS 7671 Protection Principles: ADS, Earthing, Bonding & RCDs
BS 7671 establishes two complementary tiers of protection: Basic Protection (preventing direct contact with normally live parts via insulation and IP2X/IP4X enclosures) and Fault Protection (preventing shock from exposed metalwork energized during an insulation fault).
Automatic Disconnection of Supply (ADS)
ADS is the standard protective measure in UK installations. An insulation fault drives high current through the protective earth loop back to the transformer, causing the protective device (fuse, MCB, or RCD) to disconnect within statutory times (e.g. 0.4 seconds for 230V socket circuits).
Earthing Conductors vs Main Protective Bonding Conductors
Earthing Conductor : Connects the installation's Main Earthing Terminal (MET) to the means of earthing (TN-S sheath, TN-C-S PME terminal, or TT earth electrode). It carries earth fault current back to the source to trip ADS devices.
Main Protective Bonding Conductor : Connects extraneous conductive parts (incoming metal water, gas, or oil service pipes and structural steel) directly to the MET. Bonding equalises potential across all metallic services, preventing dangerous touch voltages between accessible metalwork during faults.
Residual Current Devices (RCDs)
RCDs operate on the core-balance principle, monitoring current balance between Line and Neutral conductors. An earth leakage imbalance triggers disconnection.
Additional Protection : BS 7671 requires 30 mA RCD additional protection for (among others) socket-outlets rated up to 32 A, mobile equipment up to 32 A used outdoors, and circuits in locations such as bathrooms.
Tripping Parameters : A general-type RCD must disconnect within 300 ms at its rated residual current ( 1 × I Δ n 1 \times I_{\Delta n} 1 × I Δ n , 30 mA), and its product standard (BS EN 61008 or BS EN 61009) requires 40 ms at 5 × I Δ n 5 \times I_{\Delta n} 5 × I Δ n (150 mA). The test button checks the tripping mechanism, not the tripping time.
Physiology of Electric Shock (50 Hz AC)
Electric shock injury depends on current magnitude, duration, and pathway across the body:
Current (50 Hz AC) Physiological Effect on the Human Body
1 mA – 5 mA Perception threshold; faint tingling sensation; no loss of muscular control.
10 mA – 20 mA "Let-go" threshold; painful shock; involuntary muscle contractions (tetany); cannot release grip.
30 mA – 50 mA Severe muscle spasms; thoracic paralysis; respiratory arrest and asphyxiation if current persists.
50 mA – 100 mA Ventricular fibrillation becomes likely; uncoordinated cardiac fluttering halts blood circulation; rapid brain death.
> 1 A (1000 mA) Sustained myocardial contraction; immediate cardiac arrest; severe internal tissue burns.
GS38 Safety Criteria for Voltage Indicators
Component GS38 Compliance Standard Safety Hazard Prevented
Probe Tips Max 4 mm exposed metal (preferably 2 mm or retractable) Eliminates short circuits and explosive arc flash between phases.
Probe Body Robust moulded finger barriers / guard ridges Prevents fingers from slipping forward onto exposed live metal.
Test Leads Adequately insulated flexible leads (many with a contrasting inner layer) Visual identification of cuts, abrasion, or insulation damage.
Lead Protection HBC fuses (usually 500 mA or less) or current-limiting resistors Safely clears short-circuit fault currents without lead rupture.
Plugs & Terminals Deeply shrouded, recessed connectors Protects against contact with live pins if leads partially dislodge.
Electric Shock Emergency Rescue Protocol
Immediate, disciplined action saves lives during an electric shock emergency:
Never Touch the Casualty Directly : Touching a casualty still in contact with a live source completes an electrical circuit through your body, causing secondary electrocution.
Break Contact Safely :
Primary action : Switch off the supply at the main isolator, circuit breaker, or emergency stop.
Secondary action : If the switch is inaccessible, separate the casualty using an approved non-conductive rescue hook , dry timber pole, or dry rope, standing on an insulating mat.
Call Emergency Services (999/112) : Request an ambulance immediately, stating "electrical shock incident".
Resuscitation (CPR & AED) :
Check breathing for up to 10 seconds.
If unresponsive and not breathing normally, begin CPR immediately at 100–120 compressions per minute and depth of 5–6 cm, maintaining a 30:2 compression-to-breath ratio.
Deploy an Automated External Defibrillator (AED) immediately; follow prompts to treat ventricular fibrillation.
Burn Care & Hospitalisation : Cool electrical burns under clean cold running water for at least 20 minutes; cover loosely with sterile dressings. All electric shock casualties require hospital evaluation, as delayed cardiac arrhythmias and internal tissue trauma can emerge hours later.
ECS Exam Focus: Electric Shock Facts
The lowest current that can harm the body is measured in milliamps ; a person is in serious danger of a fatal shock at or above about 30 mA .
A 30 mA RCD should prevent a fatal shock; fuses and circuit breakers protect cables, not people.
An RCD operates on an earth fault , not on overload or short circuit.
The specific effects of a major shock are burns and cardiac arrest ; the most serious effect of touching a live part is that the heart stops.
About 50V AC is the maximum the body can withstand in dry conditions without long-term effects.
You cannot see, hear or smell electricity, so always assume a cable is live until proved otherwise.
The nominal single-phase voltage in the UK is 230V (400V three-phase).
If a workmate gets an electric shock, cut off the power and call for help ; never pull them clear with your hands.