Study guide
5.1 Control of Substances Hazardous to Health (COSHH) & Hazardous Materials
JIB ECS Health, Safety & Environmental Assessment Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Assessment Overview
About the ECS Health, Safety & Environmental Assessment
2 Chapter 1: General Health and Safety Legislation & Management
1.1 The Health and Safety at Work etc. Act 1974 & Statutory Duties 1.2 Risk Assessment, Hierarchy of Controls & CDM 2015 Regulations 1.3 Safety Signs, Workplace Inspections & Reporting Unsafe Conditions
3 Chapter 2: Manual Handling Operations & Ergonomics
2.1 Manual Handling Operations Regulations 1992 & Ergonomics 2.2 The TILE Assessment Framework & Kinetic Lifting Techniques
4 Chapter 3: Accident Reporting (RIDDOR) & First Aid Provisions
3.1 RIDDOR 2013 Statutory Reporting Requirements 3.2 Site First Aid Provisions, Accident Recording & Near-Miss Reporting
5 Chapter 4: Personal Protective Equipment at Work
4.1 Personal Protective Equipment at Work Regulations & Legal Framework 4.2 PPE Selection, Standards & Respiratory Protection
6 Chapter 5: Occupational Health, Hygiene & Site Welfare
5.1 Control of Substances Hazardous to Health (COSHH) & Hazardous Materials 5.2 Noise, Hand-Arm Vibration & CDM Welfare Facilities
7 Chapter 6: Fire Safety Fundamentals & Emergency Procedures
6.1 Fire Science, Classification of Fires & Hot Work Protocols 6.2 Portable Fire Extinguishers, Emergency Alarms & Evacuation 6.3 First Aid Response After an Accident on Site
8 Chapter 7: Fire Safety in Buildings, Compartmentation & Fire-Stopping
7.1 Passive Fire Protection, Building Compartmentation & Fire Doors 7.2 Cable Penetration Sealing & Fire-Stopping Integrity 7.3 Higher-Risk Buildings, Holistic Fire Safety & Installer Competence
9 Chapter 8: Working at Height & Access Equipment
8.1 Work at Height Regulations 2005 & Fall Protection Hierarchy 8.2 Ladders, Mobile Access Towers & MEWP Safety 8.3 Scaffolds, Inspections, Harnesses & Protecting People Below
10 Chapter 9: Work Equipment Safety (PUWER) & Lifting Operations (LOLER)
9.1 PUWER 1998 Regulations & 110V Reduced Low Voltage Tool Safety 9.2 LOLER 1998 & Safe Lifting Operations 9.3 Extension Leads, Hand Lamps & Defective Tools on Site
11 Chapter 10: Special Site Hazards (Asbestos, Confined Spaces & Ground Services)
10.1 Asbestos Awareness, Health Risks & Discovery Protocols 10.2 Confined Spaces & Avoiding Underground and Overhead Services 10.3 Site Traffic, Young Workers, Lone Working & Permits to Work
12 Chapter 11: Electrotechnical Safety & The Safe Isolation Procedure
11.1 Electricity at Work Regulations 1989 & Safe Isolation Procedure 11.2 GS38 Equipment, Earthing, RCDs & Electric Shock Rescue 11.3 Optical Fibre Safety, Electrical Permits & Site Installations
13 Chapter 12: Environmental Awareness, Waste Management & Pollution Control
12.1 Waste Duty of Care & The Waste Hierarchy 12.2 Hazardous Waste, Pollution Prevention & Site Sustainability
5.1 Control of Substances Hazardous to Health (COSHH) & Hazardous Materials
Key Takeaways Explain This Topic AI
The Control of Substances Hazardous to Health Regulations 2002 (COSHH) govern exposure to chemicals, dusts, fumes, vapours, gases, and biological agents, but exclude asbestos, lead, and ionising radiation which have separate dedicated statutory regulations.
Hazardous substances enter the human body via four primary routes: inhalation (the most rapid and common route on site), ingestion (hand-to-mouth transfer), skin absorption (permeation of epidermal lipid barriers), and injection (puncture wounds or high-pressure equipment).
Health effects are categorized as acute (immediate damage such as acid burns, asphyxiation, or dizziness) or chronic (long-term cumulative damage including occupational asthma, lung fibrosis, silicosis, and dermatitis).
Barrier creams serve only as supplementary pre-work skin-conditioning aids and must never be treated as substitutes for chemical-resistant protective gloves.
The CLP Regulation mandates standardized red-diamond hazard pictograms, complemented by 16-section Safety Data Sheets (SDS) and HSE EH40 Workplace Exposure Limits (WELs) evaluated over 8-hour LTELs and 15-minute STELs.
Last updated: October 2026
5.1 Control of Substances Hazardous to Health (COSHH) & Hazardous Materials
Hazardous substances represent a widespread risk across construction and electrotechnical sites. Electricians routinely handle or disturb chemical agents, dusts, toxic fumes, and synthetic resins. Mastering the statutory provisions of the Control of Substances Hazardous to Health Regulations 2002 (COSHH) and the Classification, Labelling and Packaging (CLP) framework is essential for passing the ECS assessment and safeguarding long-term health.
The Control of Substances Hazardous to Health Regulations 2002 (COSHH)
The Control of Substances Hazardous to Health Regulations 2002 (as amended) (COSHH) require employers to control exposure to substances that cause ill health. Under COSHH, duty-holders must assess health risks, introduce preventative controls following the hierarchy of prevention, maintain extraction equipment, monitor exposure, and provide health surveillance.
Scope and Substances Covered by COSHH
COSHH regulates hazardous substances encountered in industrial and construction work:
Chemicals: Solvents, adhesives, cleaning solutions, acids, alkalis, and lubricants.
Dusts: Inhalable and respirable dusts, including silica from chasing or drilling.
Fumes, Vapours & Gases: Rosin fumes from soldering flux, solvent vapours from adhesives, and battery off-gassing.
Biological Agents: Bacteria, fungi, and viruses in unhygienic voids, sewers, or damp soil.
Excluded Substances Under Dedicated Legislation
COSHH does not cover all hazardous materials. Specific high-hazard substances are governed by dedicated statutory instruments:
Asbestos: Regulated under the Control of Asbestos Regulations 2012 (CAR) .
Lead & Lead Compounds: Regulated under the Control of Lead at Work Regulations 2002 (CLAW) .
Ionising Radiation: Regulated under the Ionising Radiations Regulations 2017 (IRR) .
Routes of Hazardous Substance Entry
Hazardous substances cause physiological damage only after entering biological tissues via four primary pathways:
Inhalation: Breathing dusts, fumes, vapours, or gases into the respiratory tract. This is the most common and rapid route of exposure on site. Respirable particulates enter lung alveoli and cross into the bloodstream.
Ingestion: Swallowing chemical residues through hand-to-mouth transfer when eating, drinking, smoking, or vaping with unwashed hands.
Skin Absorption: Direct contact where chemical agents (e.g., solvents, degreasers, resins) penetrate the skin lipid barrier into the bloodstream without an open wound.
Injection: Punctures caused by contaminated sharps, such as jagged cable armouring wires or discarded needles in derelict risers.
Acute vs Chronic Health Effects & Occupational Dermatitis
Exposure to hazardous substances generates two distinct categories of physiological harm:
Acute Effects: Immediate reactions occurring within seconds or minutes of exposure (e.g., chemical burns, solvent dizziness, acute asphyxiation).
Chronic Effects: Long-term illnesses resulting from repeated, cumulative exposure over months or years (e.g., occupational asthma, silicosis, organ damage).
Occupational Contact Dermatitis
Dermatitis is a prevalent inflammatory skin condition among electricians:
Irritant Contact Dermatitis: Caused by physical or chemical abrasion stripping natural skin oils (e.g., repeated exposure to solvent cements, degreasers, or cement dust).
Allergic Contact Dermatitis: An irreversible immune response triggered once an operative becomes sensitised to a chemical (e.g., epoxy jointing resins, nickel, or colophony). Subsequent trace exposures trigger severe eczema.
Critical Safety Rule on Barrier Creams: Barrier creams serve solely as supplementary skin-conditioning aids. Barrier creams are never a substitute for chemical-resistant gloves. They offer zero reliable protection against hazardous chemicals.
The CLP Regulation & Chemical Hazard Classification
Chemical classification across the UK is governed by the GB CLP Regulation . The system replaces older orange square symbols with standardised diamond-shaped hazard pictograms featuring a red border, white background, and black symbol to warn operatives of physical, health, and environmental dangers before handling products on site.
Safety Data Sheets (SDS) & The 16 Standard Sections
Manufacturers must supply a Safety Data Sheet (SDS) organized into 16 standardised sections for every hazardous product:
Section 1 — Identification: Product name, manufacturer details, emergency hotline.
Section 2 — Hazard Identification: CLP pictograms, signal words ( Danger or Warning ), hazard statements.
Section 4 — First-Aid Measures: Emergency protocols for inhalation, skin/eye contact, ingestion.
Section 7 — Handling & Storage: Safe handling practices, ventilation, storage conditions.
Section 8 — Exposure Controls / Personal Protection: Statutory Workplace Exposure Limits (WELs) and mandatory PPE specifications (e.g., BS EN 374 gloves, BS EN 149 respirators).
Workplace Exposure Limits (WELs) & HSE Guidance EH40
The HSE publishes statutory Workplace Exposure Limits (WELs) in guidance document EH40 :
Long-Term Exposure Limit (LTEL): Maximum permissible airborne concentration averaged over an 8-hour Time-Weighted Average (TWA) to protect against chronic diseases.
Short-Term Exposure Limit (STEL): Maximum permissible airborne concentration averaged over a 15-minute TWA to prevent acute irritation or narcosis from short peak exposures.
WELs are expressed in parts per million ( ppm ) for gases and vapours, or milligrams per cubic metre ( mg/m³ ) for dusts and fumes.
Electrotechnical Hazardous Substances & Practical Controls
Common hazardous materials in electrical installations require targeted precautions:
PVC Solvent Cements & Adhesives: Release volatile organic compounds (VOCs). Ensure cross-ventilation and wear BS EN 374 nitrile gloves.
Degreasers & Contact Cleaners: Aerosols presenting fire and inhalation hazards. Isolate electrical supplies, eliminate ignition sources, and wear eye protection.
Battery Electrolytes (Substations & UPS): Sulfuric acid in lead-acid cells and potassium hydroxide in NiCd cells cause severe burns. Wear chemical visors, acid aprons, and neoprene gauntlets, with eyewash access.
Transformer Cooling Oils (Legacy PCBs): Pre-1986 transformers may contain carcinogenic Polychlorinated Biphenyls (PCBs). Never disturb suspect oil; report for specialist hazmat testing.
Soldering Flux & Lead Solder: Rosin flux emits toxic fumes causing asthma. Solder contains toxic lead. Deploy tip LEV extraction and wash hands before meals.
CLP Hazard Pictograms & Electrotechnical Meanings
- CLP Pictogram Symbol CLP Hazard Classification Practical Electrotechnical Site Application
- Flame Flammable liquid, aerosol, or gas Solvent cement, aerosol contact degreasers
- Corrosion Skin burns, eye damage, metal corrosion Battery sulfuric acid, caustic cleaning agents
- Skull & Crossbones Acute toxicity (fatal / toxic) Specialized biocides, industrial fumigants
Health Hazard (Star) Carcinogen, mutagen, respiratory sensitiser Rosin flux fumes (colophony), polyurethane resins
- Exclamation Mark Irritant, skin sensitiser, harmful Cable-pulling lubricants, jointing pastes
- Gas Cylinder Gas under pressure Compressed nitrogen, refrigerant cylinders
- Flame Over Circle Oxidising liquid, solid, or gas Chemical oxidisers, oxygen cylinders for brazing
- Exploding Bomb Explosive, self-reactive substance Cartridge-operated fixing tools and power charges
- Environment Hazardous to aquatic environment Dielectric transformer coolants, chemical resins
- ECS Exam Focus: Spotting and Avoiding Harmful Substances
You cannot tell by smell whether a product is harmful: many harmful substances have no smell at all.
Recognise a hazardous substance by the hazard symbol (pictogram) on the container label.
After a COSHH assessment, the risks and controls must be explained to the operatives using the substance .
Bitumens, solvents, epoxy resins and cement can cause skin problems. Asbestos is extremely harmful if inhaled but does not significantly affect the skin.
Clean very dirty hands with soap and water or a proprietary hand cleanser, never white spirit, paraffin or thinners, which strip the skin's natural oils and cause dermatitis.
Lead usually enters the blood by swallowing it from contaminated hands, so wash before eating, drinking or smoking.
Personal hygiene protects your own health and the health of others, including your family, from contamination you could carry home.
Sunlight : ultraviolet rays cause sunburn and premature skin ageing, and the most serious effect is an increased chance of skin cancer . Cover up, use sunscreen and take breaks in the shade.
Asbestos can cause asbestosis, lung cancer and mesothelioma; all types are hazardous, and suspected asbestos means stop work and report it (section 10.1).