Study guide

10.3 Site Traffic, Young Workers, Lone Working & Permits to Work

JIB ECS Health, Safety & Environmental Assessment Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Assessment Overview

About the ECS Health, Safety & Environmental Assessment

2 Chapter 1: General Health and Safety Legislation & Management

1.1 The Health and Safety at Work etc. Act 1974 & Statutory Duties 1.2 Risk Assessment, Hierarchy of Controls & CDM 2015 Regulations 1.3 Safety Signs, Workplace Inspections & Reporting Unsafe Conditions

3 Chapter 2: Manual Handling Operations & Ergonomics

2.1 Manual Handling Operations Regulations 1992 & Ergonomics 2.2 The TILE Assessment Framework & Kinetic Lifting Techniques

4 Chapter 3: Accident Reporting (RIDDOR) & First Aid Provisions

3.1 RIDDOR 2013 Statutory Reporting Requirements 3.2 Site First Aid Provisions, Accident Recording & Near-Miss Reporting

5 Chapter 4: Personal Protective Equipment at Work

4.1 Personal Protective Equipment at Work Regulations & Legal Framework 4.2 PPE Selection, Standards & Respiratory Protection

6 Chapter 5: Occupational Health, Hygiene & Site Welfare

5.1 Control of Substances Hazardous to Health (COSHH) & Hazardous Materials 5.2 Noise, Hand-Arm Vibration & CDM Welfare Facilities

7 Chapter 6: Fire Safety Fundamentals & Emergency Procedures

6.1 Fire Science, Classification of Fires & Hot Work Protocols 6.2 Portable Fire Extinguishers, Emergency Alarms & Evacuation 6.3 First Aid Response After an Accident on Site

8 Chapter 7: Fire Safety in Buildings, Compartmentation & Fire-Stopping

7.1 Passive Fire Protection, Building Compartmentation & Fire Doors 7.2 Cable Penetration Sealing & Fire-Stopping Integrity 7.3 Higher-Risk Buildings, Holistic Fire Safety & Installer Competence

9 Chapter 8: Working at Height & Access Equipment

8.1 Work at Height Regulations 2005 & Fall Protection Hierarchy 8.2 Ladders, Mobile Access Towers & MEWP Safety 8.3 Scaffolds, Inspections, Harnesses & Protecting People Below

10 Chapter 9: Work Equipment Safety (PUWER) & Lifting Operations (LOLER)

9.1 PUWER 1998 Regulations & 110V Reduced Low Voltage Tool Safety 9.2 LOLER 1998 & Safe Lifting Operations 9.3 Extension Leads, Hand Lamps & Defective Tools on Site

11 Chapter 10: Special Site Hazards (Asbestos, Confined Spaces & Ground Services)

10.1 Asbestos Awareness, Health Risks & Discovery Protocols 10.2 Confined Spaces & Avoiding Underground and Overhead Services 10.3 Site Traffic, Young Workers, Lone Working & Permits to Work

12 Chapter 11: Electrotechnical Safety & The Safe Isolation Procedure

11.1 Electricity at Work Regulations 1989 & Safe Isolation Procedure 11.2 GS38 Equipment, Earthing, RCDs & Electric Shock Rescue 11.3 Optical Fibre Safety, Electrical Permits & Site Installations

13 Chapter 12: Environmental Awareness, Waste Management & Pollution Control

12.1 Waste Duty of Care & The Waste Hierarchy 12.2 Hazardous Waste, Pollution Prevention & Site Sustainability

10.3 Site Traffic, Young Workers, Lone Working & Permits to Work

Key Takeaways Explain This Topic AI

Pedestrian routes keep people and vehicles apart; if the system is not working, tell your supervisor rather than dodging traffic.

Never ride on plant or vehicles unless they are designed to carry passengers and have a seat for you.

Young people under 18 are at particular risk because they are inexperienced and may not recognise danger, so employers must risk assess and supervise them.

When working alone, make sure someone responsible knows where you are and agree regular check-ins.

A permit to work is a written safe system of work that allows high-risk work to start only when the specified precautions are in place.

Last updated: October 2026

10.3 Site Traffic, Young Workers, Lone Working & Permits to Work

The Special Site Hazards topic is not only about asbestos, confined spaces and buried cables. The ECS syllabus also expects you to understand the dangers to pedestrians from vehicles on site, the additional risks to young people and lone workers, and how permit-to-work systems control high-risk jobs. In these areas your own behaviour, such as where you walk, what you ride on and who knows where you are, makes the difference.

Vehicles and Pedestrians

Being struck by a moving vehicle is one of the main causes of death on construction sites. CDM 2015 requires construction sites to be organised so that pedestrians and vehicles can move safely , and traffic routes must be suitable and properly maintained. A good site traffic plan includes:

Segregated routes : separate, clearly marked pedestrian walkways with barriers, and separate gates for people and vehicles.

One-way systems and turning areas, so that reversing is kept to a minimum.

Trained vehicle marshals (banksmen) to guide reversing vehicles where reversing cannot be avoided.

Visibility aids such as mirrors, cameras and reversing alarms, plus high-visibility clothing for everyone on foot.

Speed limits , lighting and safe crossing points.

What this means for you:

Use the pedestrian routes provided. If you keep having to dodge site traffic because the routes do not work, tell your supervisor about the danger . Do not just walk round the edges of the site or have a quiet word with the drivers.

Never ride on plant or vehicles unless they are designed to carry passengers and have a proper seat for you. Riding on the back of a dumper, in a telehandler bucket or on the step of a lorry kills workers every year, whatever the distance or the weather.

Stay out of blind spots. If you cannot see the driver's face, the driver cannot see you.

Never walk under suspended loads or through areas where plant is working without the marshal's signal.

Young People at Work

A young person is anyone under 18. Health and safety guidance lists young people as being at particular risk because they are inexperienced and may not recognise danger ; they may also be keen to impress or reluctant to ask questions. The Management of Health and Safety at Work Regulations 1999 require employers to:

Carry out a risk assessment that takes account of the young person's inexperience and immaturity before they start work.

Not employ young people on work beyond their physical or psychological capacity, or involving harmful exposure to toxic substances, radiation, extreme heat or cold, noise or vibration, unless it is necessary for their training, they are supervised by a competent person, and the risk is reduced as low as reasonably practicable.

Provide close supervision , clear instructions and training.

Young people get the same PPE and the same legal protection as everyone else. Nothing in law allows them to be left to work alone to gain experience.

Lone Working

Working alone is not automatically illegal, but it must be risk assessed . Some work must not be done alone, such as entering a confined space, work on or near live conductors where accompaniment is one of the precautions, or work where an injury would leave you unable to summon help. Where lone working is allowed:

Make sure someone responsible knows where you are , what you are doing and when you expect to finish.

Agree regular check-in times by phone or radio, and what will happen if you miss one.

Carry a charged phone or a lone-worker alarm .

Keep to the agreed safe working arrangements: do not skip PPE or take on extra tasks because nobody is watching.

If you have a problem, ask for help rather than trying to sort it out yourself.

Permit-to-Work Systems

A permit to work is a written safe system of work used to control certain types of high-risk work. It allows work to start only when site procedures have been clarified and the specified precautions are in place. Permits are commonly used for:

  • Work Typical permit controls
  • Hot work Combustibles cleared, extinguisher present, fire watch after the work
  • Confined space entry Atmosphere tested, ventilation, rescue plan and rescue equipment
  • Work on high-voltage electrical systems Isolation, earthing, the equipment made safe and the work defined
  • Excavation near buried services Plans checked, services located, hand-dig zone marked
  • Roof work and fragile surfaces Access, edge protection, covers and weather limits

A permit states what the work is, where it is, which hazards have been controlled, which precautions must stay in place, and how long it is valid . It is signed by the person issuing it and accepted by the person in charge of the work, and it must be handed back and cancelled when the work is finished. A permit is not a way of speeding up a job, guaranteeing payment or checking tools; its purpose is to help ensure a safe system of work.

Excavations

Before anyone enters an excavation, it must be inspected by a competent person who understands the risks of the sides collapsing, falling materials, flooding and buried services. Excavations must be inspected at the start of each shift and after any event that could affect their stability, such as a fall of material. Keep spoil, materials and plant back from the edge, and never enter an unsupported trench where the sides could collapse.

ECS Exam Focus

Dodging site traffic on your route: tell your supervisor about the danger.

Riding in plant: only if it is designed to carry passengers .

Young people: at risk because they are inexperienced and may not recognise danger .

Working alone: make sure someone responsible knows where you are .

Purpose of a permit to work: to help ensure a safe system of work .

Before entering an excavation: inspection by a competent person .