Study guide

8.2 Trigonometric Method for Multi-Leg Slings

LEEA Foundation Certificate Lifting Equipment Engineers Association, UK

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

About the LEEA Foundation Certificate The LEEA Qualification Pathway, Diplomas & the TEAM Card

2 Legislation, Standards & Regulatory Framework

1.1 Health and Safety at Work etc. Act 1974 & Management Regulations 1.2 Provision and Use of Work Equipment Regulations 1998 (PUWER 1998) 1.3 Lifting Operations and Lifting Equipment Regulations 1998 (LOLER 1998) 1.4 Standards, Marking & Documentation 1.5 Controlling Risks, Hazard Management & the 5-Step Risk Assessment

3 Principles of Mechanics & Material Properties

2.1 Forces, Mass, Weight & Center of Gravity 2.2 Mechanical Properties: Stress, Strain & Safety Factors 2.3 WLL, SWL & Rating Concepts 2.4 Heat Treatment & Metallurgy in Lifting Equipment 2.5 Units of Measure, Symbols & Conversions 2.6 Basic Machines, Mechanical Advantage, Velocity Ratio & Efficiency 2.7 Verification, Test Machines, Calibration & NDT Methods

4 Shackles, Eyebolts & Threaded Fittings

3.1 Shackles: Types, Standards & Rating 3.2 Shackle Inspection, Safe Use & Rejection Criteria 3.3 Eyebolts & Eyenuts: Types & Angular Loading 3.4 Eyebolt Installation, Inspection & Rejection Criteria 3.5 Rigging Screws & Turnbuckles

5 Chain Slings & Components

4.1 Chain Sling Construction & Grades 4.2 Chain Components: Master Links, Hooks & Couplers 4.3 Chain Sling Marking, Certification & Safe Use 4.4 Chain Sling Inspection, Wear & Rejection Criteria

6 Wire Rope Slings & Terminations

5.1 Wire Rope Construction & Cores 5.2 Wire Rope Terminations & Assemblies 5.3 Wire Rope Sling Ratings & Safe Use 5.4 Wire Rope Sling Inspection & Discard Criteria

7 Textile Slings & Below-the-Hook Accessories

6.1 Flat Woven Webbing Slings 6.2 Roundslings & High-Performance Fiber Slings 6.3 Textile Sling Inspection, Chemical & Mechanical Damage 6.4 Plate Clamps, Beam Clamps & Below-the-Hook Lifters 6.5 Fibre Rope Slings & Natural Fibre Ropes 6.6 Crane Forks & C-Hooks

8 Manual & Powered Lifting Appliances

7.1 Manual Chain Blocks & Lever Hoists 7.2 Wire Rope Pull-Lifts, Winches & Jacks 7.3 Powered Hoists: Electric & Pneumatic 7.4 Cranes, Structures & Supporting Equipment 7.5 Mobile Cranes, Tower Cranes & Offshore Cranes 7.6 Offshore Containers, Pad Eyes & Lifting Sets

9 Rigging Calculations, Mode Factors & Complex Lifts

8.1 Uniform Load Method (ULM) for Multi-Leg Slings 8.2 Trigonometric Method for Multi-Leg Slings 8.3 Hitch Mode Factors: Choked, Basket & Wrap Hitches 8.4 Center of Gravity Off-Center & Asymmetric Load Calculations

8.2 Trigonometric Method for Multi-Leg Slings

Key Takeaways Explain This Topic AI

The Trigonometric Method calculates exact sling leg tension (T) using vector resolution based on precise measured angles, represented by T = W / (N * cos theta) (where theta is the angle to the vertical) or T = W / (N * sin alpha) (where alpha is the angle to the horizontal).

Under LEEA standards and BS EN guidelines, the Trigonometric Method is ONLY permitted for dedicated, single-purpose lifting applications with fixed geometry, known center of gravity, symmetrical leg lengths, and where angles are strictly measured and verified.

As the sling leg angle to the vertical (theta) increases, leg tension grows non-linearly: at 0° (vertical) T = 0.50 W; at 30° T = 0.577 W; at 45° T = 0.707 W; at 60° T = 1.000 W; and at 75° T = 1.932 W (for a 2-leg sling).

The Trigonometric Method allows higher load utilization than ULM when sling angles are small (e.g. theta <= 30°), but requires competent engineering oversight to prevent overload if geometry shifts.

Horizontal compressive force (H = T * sin theta = (W / N) * tan theta) must always be calculated to ensure the load structure can withstand internal crushing forces exerted by the sling legs.

Last updated: August 2026

While the Uniform Load Method (ULM) provides a safe, conservative rating system for general-purpose reusable slings, the Trigonometric Method calculates exact sling leg tension based on actual vector geometry. By calculating precise tension forces ( T T T ) as a function of the specific leg angle, lifting engineers can optimize sling selection for engineered lifts. However, because the Trigonometric Method relies on precise, unvarying geometry, standard regulatory bodies—including LEEA and BS EN standards —impose strict rules governing when and how trigonometric rating may be lawfully applied.

Vector Derivation and Mathematical Formulations

In any multi-leg sling system carrying a total weight W W W evenly distributed across N N N sling legs, static equilibrium requires that the sum of the vertical force components of all legs must equal the total load weight.

Let:

W = Total gross load weight (tonnes or kN) W = \text{Total gross load weight (tonnes or kN)} W = Total gross load weight (tonnes or kN)

N = Number of load-bearing sling legs N = \text{Number of load-bearing sling legs} N = Number of load-bearing sling legs

θ = β = Angle of sling leg to the vertical plumb line (degrees) \theta = \beta = \text{Angle of sling leg to the vertical plumb line (degrees)} θ = β = Angle of sling leg to the vertical plumb line (degrees)

α = Angle of sling leg to the horizontal load surface (degrees) \alpha = \text{Angle of sling leg to the horizontal load surface (degrees)} α = Angle of sling leg to the horizontal load surface (degrees)

Because the vertical plumb line and the horizontal load plane are perpendicular, θ + α = 90 ∘ \theta + \alpha = 90^\circ θ + α = 9 0 ∘ .

1. Formula Using Angle to Vertical ( θ \theta θ )

The vertical force component supported by each leg is V = W N V = \frac{W}{N} V = N W ​ . From right-triangle trigonometry at the hook apex: cos ⁡ θ = Vertical Force per Leg Tension per Leg = W / N T \cos\theta = \frac{\text{Vertical Force per Leg}}{\text{Tension per Leg}} = \frac{W / N}{T} cos θ = Tension per Leg Vertical Force per Leg ​ = T W / N ​

  • Solving for Leg Tension ( T T T ): T = W N ⋅ cos ⁡ θ T = \frac{W}{N \cdot \cos\theta} T = N ⋅ cos θ W ​
  • 2. Formula Using Angle to Horizontal ( α \alpha α )

If the angle is measured from the horizontal surface of the load ( α \alpha α ): sin ⁡ α = W / N T ⟹ T = W N ⋅ sin ⁡ α \sin\alpha = \frac{W / N}{T} \implies T = \frac{W}{N \cdot \sin\alpha} sin α = T W / N ​ ⟹ T = N ⋅ sin α W ​

Equivalence of Formulas

Since cos ⁡ θ = sin ⁡ ( 90 ∘ − θ ) = sin ⁡ α \cos\theta = \sin(90^\circ - \theta) = \sin\alpha cos θ = sin ( 9 0 ∘ − θ ) = sin α , both equations yield identical leg tension values. Riggers must verify which angle convention is being referenced to avoid catastrophic errors (e.g., confusing a 30 ∘ 30^\circ 3 0 ∘ angle to vertical with a 30 ∘ 30^\circ 3 0 ∘ angle to horizontal).

LEEA Regulations & Conditions for Trig Method Use

Under LEEA guidelines and BS EN 818 / BS EN 13414 , general-purpose multi-leg slings intended for routine, day-to-day site lifting must ALWAYS be rated and marked according to the Uniform Load Method.

The Trigonometric Method is ONLY PERMITTED when ALL of the following engineering criteria are satisfied:

Dedicated Single-Purpose Lift: The sling assembly is manufactured and used exclusively for a single, specific load item (e.g., a turbine rotor or pre-fabricated offshore module).

Fixed and Known Geometry: The picking points, lug positions, and hook height are permanently fixed and cannot change during handling.

Verified Center of Gravity: The location of the load's Center of Gravity (CG) is accurately known, verified by engineering calculation or weighing, and centered relative to the picking points.

Matched Leg Lengths: The sling legs are manufactured to exact, precision tolerances to ensure equal load sharing.

Specialized Tagging: The sling identification tag is explicitly stamped with the specific load geometry, exact leg angle, and dedicated Working Load Limit (e.g., "RATED FOR TURBINE SKID #4 ONLY AT 25° TO VERTICAL" ).

If a sling rated by the Trigonometric Method is accidentally used for a different load with a wider angle, severe overload and structural failure can result.

Angle vs. Tension Multiplier Analysis

To visualize how leg tension increases as sling legs spread wider, consider a 2-leg sling lifting a 1.0-tonne load ( W = 1.0 t , N = 2 W = 1.0\text{ t}, N = 2 W = 1.0 t , N = 2 ). The vertical load component per leg is 0.5 tonnes 0.5\text{ tonnes} 0.5 tonnes .

Angle to Vertical ( θ \theta θ ) Angle to Horizontal ( α \alpha α ) cos ⁡ θ \cos\theta cos θ Tension per Leg ( T T T ) Tension Factor ( T / W T / W T / W ) Percentage Increase over Vertical

  • 0° 90° 1.0000 0.500 t 0.500\text{ t} 0.500 t 0.500 Baseline (0%)
  • 15° 75° 0.9659 0.518 t 0.518\text{ t} 0.518 t 0.518 +3.6%
  • 30° 60° 0.8660 0.577 t 0.577\text{ t} 0.577 t 0.577 +15.5%
  • 45° 45° 0.7071 0.707 t 0.707\text{ t} 0.707 t 0.707 +41.4%
  • 60° 30° 0.5000 1.000 t 1.000\text{ t} 1.000 t 1.000 +100.0%
  • 75° 15° 0.2588 1.932 t 1.932\text{ t} 1.932 t 1.932 +286.4%

Key engineering observations from this data:

At θ = 45 ∘ \theta = 45^\circ θ = 4 5 ∘ , leg tension is 1.414 1.414 1.414 times the vertical load share ( 0.707 W 0.707 W 0.707 W ).

At θ = 60 ∘ \theta = 60^\circ θ = 6 0 ∘ , leg tension doubles relative to vertical baseline ( 1.000 W 1.000 W 1.000 W ), meaning each leg carries the entire weight of the load.

Beyond 60 ∘ 60^\circ 6 0 ∘ , tension grows exponentially. At θ = 75 ∘ \theta = 75^\circ θ = 7 5 ∘ , each leg experiences nearly double the total load weight ( 1.932 W 1.932 W 1.932 W ).

Horizontal Compressive Vector Forces

In addition to vertical leg tension, angled sling legs exert powerful inward horizontal forces ( H H H ) on the load. These compressive forces attempt to crush structural members, buckling slender beams or cylindrical shells.

The horizontal force per sling leg is calculated as: H = T ⋅ sin ⁡ θ = ( W N ⋅ cos ⁡ θ ) ⋅ sin ⁡ θ = W N ⋅ tan ⁡ θ H = T \cdot \sin\theta = \left(\frac{W}{N \cdot \cos\theta}\right) \cdot \sin\theta = \frac{W}{N} \cdot \tan\theta H = T ⋅ sin θ = ( N ⋅ cos θ W ​ ) ⋅ sin θ = N W ​ ⋅ tan θ

For a 2-leg sling lifting weight W W W :

At θ = 30 ∘ \theta = 30^\circ θ = 3 0 ∘ : H = ( W / 2 ) ⋅ tan ⁡ ( 30 ∘ ) = 0.289 W H = (W / 2) \cdot \tan(30^\circ) = 0.289 W H = ( W /2 ) ⋅ tan ( 3 0 ∘ ) = 0.289 W

At θ = 45 ∘ \theta = 45^\circ θ = 4 5 ∘ : H = ( W / 2 ) ⋅ tan ⁡ ( 45 ∘ ) = 0.500 W H = (W / 2) \cdot \tan(45^\circ) = 0.500 W H = ( W /2 ) ⋅ tan ( 4 5 ∘ ) = 0.500 W

At θ = 60 ∘ \theta = 60^\circ θ = 6 0 ∘ : H = ( W / 2 ) ⋅ tan ⁡ ( 60 ∘ ) = 0.866 W H = (W / 2) \cdot \tan(60^\circ) = 0.866 W H = ( W /2 ) ⋅ tan ( 6 0 ∘ ) = 0.866 W

When lifting fragile or thin-walled structures, a spreader beam must be used to absorb these horizontal compressive forces, keeping the sling legs vertical below the beam.

  • Step-by-Step Worked Numerical Examples
  • Worked Example 1: Precision Trigonometric Tension Calculation

Problem: A dedicated offshore compressor skid weighing 14.5 tonnes 14.5\text{ tonnes} 14.5 tonnes is fitted with a custom 4-leg wire rope sling. The rigging geometry is fixed such that each leg forms an angle of exactly θ = 22 ∘ \theta = 22^\circ θ = 2 2 ∘ to the vertical plumb line. A spreader frame ensures equal load sharing across all 4 legs ( N = 4 N = 4 N = 4 ). Calculate:

Tension in each sling leg ( T T T ).

Total inward horizontal compressive force acting on the skid frame.

Solution:

Calculate Leg Tension ( T T T ): T = W N ⋅ cos ⁡ θ = 14.5 tonnes 4 ⋅ cos ⁡ ( 22 ∘ ) T = \frac{W}{N \cdot \cos\theta} = \frac{14.5\text{ tonnes}}{4 \cdot \cos(22^\circ)} T = N ⋅ cos θ W ​ = 4 ⋅ cos ( 2 2 ∘ ) 14.5 tonnes ​ cos ⁡ ( 22 ∘ ) = 0.9272 \cos(22^\circ) = 0.9272 cos ( 2 2 ∘ ) = 0.9272 T = 14.5 4 ⋅ 0.9272 = 14.5 3.7087 = 3.910 tonnes per leg T = \frac{14.5}{4 \cdot 0.9272} = \frac{14.5}{3.7087} = 3.910\text{ tonnes per leg} T = 4 ⋅ 0.9272 14.5 ​ = 3.7087 14.5 ​ = 3.910 tonnes per leg

Calculate Horizontal Compressive Force per Side ( H H H ): H = W N ⋅ tan ⁡ ( 22 ∘ ) = 14.5 4 ⋅ 0.4040 = 3.625 × 0.4040 = 1.465 tonnes per leg H = \frac{W}{N} \cdot \tan(22^\circ) = \frac{14.5}{4} \cdot 0.4040 = 3.625 \times 0.4040 = 1.465\text{ tonnes per leg} H = N W ​ ⋅ tan ( 2 2 ∘ ) = 4 14.5 ​ ⋅ 0.4040 = 3.625 × 0.4040 = 1.465 tonnes per leg

Since there are two legs on each side of the frame, the total horizontal compression along the longitudinal axis is 2 × 1.465 = 2.93 tonnes 2 \times 1.465 = 2.93\text{ tonnes} 2 × 1.465 = 2.93 tonnes .

Worked Example 2: Comparing Trigonometric Method vs. ULM Capacity

Problem: Compare the rated capacity of a 2-leg 16mm Grade 80 chain sling ( W L L s i n g l e = 8.0 tonnes WLL_{single} = 8.0\text{ tonnes} W L L s in g l e ​ = 8.0 tonnes ) operating at a fixed angle of θ = 20 ∘ \theta = 20^\circ θ = 2 0 ∘ to the vertical using:

The Uniform Load Method.

The Trigonometric Method.

Solution:

ULM Capacity: For 20 ∘ 20^\circ 2 0 ∘ to vertical ( 0 ∘ 0^\circ 0 ∘ – 45 ∘ 45^\circ 4 5 ∘ range), ULM factor is 1.4 1.4 1.4 : W L L U L M = 1.4 × 8.0 t = 11.2 tonnes WLL_{ULM} = 1.4 \times 8.0\text{ t} = 11.2\text{ tonnes} W L L UL M ​ = 1.4 × 8.0 t = 11.2 tonnes

Trigonometric Capacity: W L L T r i g = 2 ⋅ W L L s i n g l e ⋅ cos ⁡ ( 20 ∘ ) = 2 ⋅ 8.0 ⋅ 0.9397 = 15.035 tonnes WLL_{Trig} = 2 \cdot WLL_{single} \cdot \cos(20^\circ) = 2 \cdot 8.0 \cdot 0.9397 = 15.035\text{ tonnes} W L L T r i g ​ = 2 ⋅ W L L s in g l e ​ ⋅ cos ( 2 0 ∘ ) = 2 ⋅ 8.0 ⋅ 0.9397 = 15.035 tonnes

Engineering Analysis: The Trigonometric Method allows a higher payload ( 15.03 t 15.03\text{ t} 15.03 t vs 11.2 t 11.2\text{ t} 11.2 t ) because the actual angle ( 20 ∘ 20^\circ 2 0 ∘ ) is significantly steeper than the conservative 45 ∘ 45^\circ 4 5 ∘ baseline assumed by ULM. However, this higher capacity is ONLY legal if the lift satisfies all LEEA requirements for dedicated, fixed-geometry lifting!