Study guide
3.5 Rigging Screws & Turnbuckles
LEEA Foundation Certificate Lifting Equipment Engineers Association, UK
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
About the LEEA Foundation Certificate The LEEA Qualification Pathway, Diplomas & the TEAM Card
2 Legislation, Standards & Regulatory Framework
1.1 Health and Safety at Work etc. Act 1974 & Management Regulations 1.2 Provision and Use of Work Equipment Regulations 1998 (PUWER 1998) 1.3 Lifting Operations and Lifting Equipment Regulations 1998 (LOLER 1998) 1.4 Standards, Marking & Documentation 1.5 Controlling Risks, Hazard Management & the 5-Step Risk Assessment
3 Principles of Mechanics & Material Properties
2.1 Forces, Mass, Weight & Center of Gravity 2.2 Mechanical Properties: Stress, Strain & Safety Factors 2.3 WLL, SWL & Rating Concepts 2.4 Heat Treatment & Metallurgy in Lifting Equipment 2.5 Units of Measure, Symbols & Conversions 2.6 Basic Machines, Mechanical Advantage, Velocity Ratio & Efficiency 2.7 Verification, Test Machines, Calibration & NDT Methods
4 Shackles, Eyebolts & Threaded Fittings
3.1 Shackles: Types, Standards & Rating 3.2 Shackle Inspection, Safe Use & Rejection Criteria 3.3 Eyebolts & Eyenuts: Types & Angular Loading 3.4 Eyebolt Installation, Inspection & Rejection Criteria 3.5 Rigging Screws & Turnbuckles
5 Chain Slings & Components
4.1 Chain Sling Construction & Grades 4.2 Chain Components: Master Links, Hooks & Couplers 4.3 Chain Sling Marking, Certification & Safe Use 4.4 Chain Sling Inspection, Wear & Rejection Criteria
6 Wire Rope Slings & Terminations
5.1 Wire Rope Construction & Cores 5.2 Wire Rope Terminations & Assemblies 5.3 Wire Rope Sling Ratings & Safe Use 5.4 Wire Rope Sling Inspection & Discard Criteria
7 Textile Slings & Below-the-Hook Accessories
6.1 Flat Woven Webbing Slings 6.2 Roundslings & High-Performance Fiber Slings 6.3 Textile Sling Inspection, Chemical & Mechanical Damage 6.4 Plate Clamps, Beam Clamps & Below-the-Hook Lifters 6.5 Fibre Rope Slings & Natural Fibre Ropes 6.6 Crane Forks & C-Hooks
8 Manual & Powered Lifting Appliances
7.1 Manual Chain Blocks & Lever Hoists 7.2 Wire Rope Pull-Lifts, Winches & Jacks 7.3 Powered Hoists: Electric & Pneumatic 7.4 Cranes, Structures & Supporting Equipment 7.5 Mobile Cranes, Tower Cranes & Offshore Cranes 7.6 Offshore Containers, Pad Eyes & Lifting Sets
9 Rigging Calculations, Mode Factors & Complex Lifts
8.1 Uniform Load Method (ULM) for Multi-Leg Slings 8.2 Trigonometric Method for Multi-Leg Slings 8.3 Hitch Mode Factors: Choked, Basket & Wrap Hitches 8.4 Center of Gravity Off-Center & Asymmetric Load Calculations
3.5 Rigging Screws & Turnbuckles
Key Takeaways Explain This Topic AI
A rigging screw (bottle screw) has a tubular body internally threaded at each end—one right-hand and one left-hand thread—accepting terminal fittings such as screwed eyes, hooks, or forks.
A turnbuckle has an open body formed of reins (a frame) with internally threaded bosses at each end, again with one right-hand and one left-hand thread.
Rotating the body draws both terminals equally inward (tensioning) or releases them outward, allowing precise length adjustment without twisting the attached ropes or stays.
Rigging screw bodies have a drilled inspection hole across each end so the user can verify that the threaded portion of each terminal fitting is adequately engaged with the body.
Rigging screws and turnbuckles are lifting accessories subject to pre-use checks and 6-monthly thorough examination; bent bodies, damaged threads, inadequate thread engagement, and missing lock nuts are rejection defects.
Last updated: August 2026
Rigging Screws & Turnbuckles
Rigging screws and turnbuckles are adjustable tensioning fittings used to set precise lengths in standing rigging, guardrail and lashing systems, sling legs, and guys. Although they perform no lifting motion themselves, they are lifting accessories when incorporated into a lifting or load-retaining system, and they are examined against the same marking, rating, and inspection disciplines as shackles and eyebolts.
1. Construction: Rigging Screw vs. Turnbuckle
- Feature Rigging Screw (Bottle Screw) Turnbuckle
- Body Tubular (closed) body enclosing the threads Open body consisting of reins (a forged frame)
Threads Internally threaded at each end— one right-hand, one left-hand Internally threaded bosses at each end— one right-hand, one left-hand
Terminal fittings Screwed eyes, hooks, or forks of various forms Screwed eyes, hooks, or forks of various forms
Thread verification Drilled inspection hole across each end of the body Thread engagement visible directly through the open frame
Typical uses Static guys, standing rigging, lashings, tensioning where a closed body protects threads Guardrails, shade and lashing systems, light tensioning duties RIGGING SCREW (TUBULAR BODY) TURNBUCKLE (OPEN BODY)
- (EYE)===[======= BODY =======]===(FORK) (EYE)===[REIN] [REIN]===(FORK)
- RH thread | LH thread open frame
- ^ inspection hole drilled
- through body wall
- 2. The Adjustment Principle: Right-Hand + Left-Hand Threads
Because one end of the body carries a right-hand thread and the other a left-hand thread, rotating the body in one direction draws both terminals inward simultaneously ; rotating it the other way releases them. This gives precise, positive length adjustment without rotating the attached rope, stay, or sling—and without twisting the terminals.
Locking: Once the correct tension is set, the terminal lock nuts (where fitted) must be tightened hard against the body to prevent the assembly vibrating loose.
No shock loading: Rigging screws and turnbuckles are designed for steady tension. Impact or snatch loads can strip threads or bend the frame; they must not be used as dynamic shock-absorbing links.
Adjustment range: Never screw the terminals out beyond the maximum safe take-up; adequate thread engagement must be maintained at all times (see the inspection hole rule below).
3. The Drilled Inspection Hole (Thread Engagement Check)
A rigging screw's tubular body hides the threads, so the user cannot see whether each terminal is safely engaged. To solve this, the body is drilled with an inspection hole across each end :
Screw each terminal in until its threaded end appears at (or beyond) the inspection hole .
If the terminal end does not reach the hole, engagement is inadequate—the fitting could pull out under load.
When adjusting out, never back a terminal so far that its end retreats behind the inspection hole.
This simple drilled witness hole is a frequently examined detail: its purpose is to facilitate checking that the threaded portion of the terminal fitting has adequately engaged with the body .
4. Rating, Marking & Safe Use
WLL marking: The assembly must be marked with its Working Load Limit, manufacturer's mark, and traceability code; the rating applies to straight axial tension only.
Matching threads: Terminal fittings must match the body thread form and pitch exactly (metric coarse, UNC, or Whitworth); mixing thread forms strips the first threads and gives a false sense of security (the same fatal hazard described for eyebolts in Section 3.3).
No side loading: Load must remain axial. Side pulls bend the frame and open the thread flanks.
No welding or heating: As with all certified lifting accessories, welding or flame heating destroys heat treatment and is prohibited.
5. Inspection & Rejection Criteria
As lifting accessories, rigging screws and turnbuckles require a pre-use visual check before every use and a thorough examination by a Competent Person at least every 6 months (LOLER Regulation 9(3)(a)(i), Section 1.3).
- Defect Rejection Action
- Thread engagement below the inspection-hole witness Reject / re-fit correctly before use
- Bent or distorted body, reins, or frame Reject
- Stripped, galled, corroded, or damaged threads Reject
- Cracks at the body-to-terminal junction (check with MPI if suspected) Reject
- Missing lock nuts or seized adjustment Repair or reject
- WLL / identification marking illegible or missing Withdraw from service
Practical note: When used for sling-leg length adjustment on asymmetric loads (Section 8.4), a turnbuckle forms part of the load path—its WLL, not merely its adjustment range, must be verified against the calculated leg tension.