Study guide

8.2 Stopping Trains and Protecting the Line

Personal Track Safety PTS

Track your progress as you read

Finished sections get a check mark.

1 Introduction

About the PTS Qualification & Assessment

2 Chapter 1: Railway Infrastructure & Track Layout

1.1 Track Layout, Track Components & Permanent Way Terminology 1.2 Points, Crossings, Switch Blades & Associated Hazards 1.3 Limited Clearances, Refuges & Trackside Structures

3 Chapter 2: Sentinel Scheme, Fitness for Work & PPE

2.1 The Sentinel Scheme, Card System & Sponsorship 2.2 Medical Fitness, Drugs & Alcohol Policy & Fatigue Management 2.3 Trackside Personal Protective Equipment Standards

4 Chapter 3: Walking and Working On or Near the Line

3.1 On or Near the Line, the Lineside & Going onto the Railway 3.2 Positions of Safety, Walking Alone & Crossing the Line 3.3 Procedures When a Train Approaches

5 Chapter 4: AC Electrification & Overhead Line Safety

4.1 AC Overhead Line Equipment Principles & Components 4.2 AC Clearances, Live Equipment, Bonds & Overhead Line Permits 4.3 Overhead Line Emergencies, Emergency Switch-Off & Rescue

6 Chapter 5: DC Conductor Rail & Electrification Safety

5.1 DC Electrification Infrastructure & Operating Voltages 5.2 DC Working Distances, Safe Stepping & Bridging Risks 5.3 Flooding, Weather & DC Emergency Switch-Off

7 Chapter 6: Safe Systems of Work & Trackside Safety Roles

6.1 The Safe System of Work and Its Hierarchy 6.2 Trackside Safety Roles and How to Recognise Them 6.3 Briefings, During the Work & the Worksafe Procedure

8 Chapter 7: Safety-Critical Communications & Trackside Signage

7.1 Communicating Clearly: Safety-Critical Communications 7.2 Signals, Trackside Signs & Whistle Boards 7.3 Railway Telephones, Radio & Mobile Phones

9 Chapter 8: Railway Emergency Procedures & Stopping Trains

8.1 Emergencies: Danger to Trains and Emergency Calls 8.2 Stopping Trains and Protecting the Line 8.3 Reporting Your Concerns: Close Calls, CIRAS & Statutory Reporting

8.2 Stopping Trains and Protecting the Line

Key Takeaways Explain This Topic AI

In daylight show a red flag, or if you have none raise both arms above your head; in darkness or poor visibility show a red light or wave any light violently.

If you have a track circuit operating clip, place it on each affected line first, except where there is a fourth rail; on a third-rail line put the first clip on the running rail furthest from the conductor rail.

If you cannot contact the signaller, walk towards approaching trains and place three detonators 20 metres apart at 2 kilometres (1¼ miles) on each affected line.

Stand at least 30 metres from detonators while showing a hand danger signal, and never use a detonator more than five years old.

If the signaller tells you the line is protected, you do not need to continue to the 2-kilometre point.

Last updated: October 2026

8.2 Stopping Trains and Protecting the Line

If a line becomes unsafe, the driver of any approaching train must be alerted to the danger ahead. This is known as protecting the line . The rules are in section 8 of HB1 (stopping trains in an emergency), section 8 of the PTS handbook (RT3170), and Rule Book Handbook 2, Instructions for track workers who use emergency protection equipment (GERT8000-HB2), which applies to track workers trained to carry out emergency protection.

1. The Hand Danger Signal

In an emergency you can stop a train by giving a hand danger signal . It must be clearly visible to the driver. HB1 section 8.2 says:

Conditions How to show the hand danger signal

Daylight Show a red flag . If you do not have a red flag, raise both arms above your head . If you are riding on a vehicle, raise one arm held out horizontally.

Darkness or poor visibility Show a red light to the driver, or wave any light violently .

If possible, give the signal in a way that does not stop other trains approaching on other lines (PTS handbook section 8.2).

Give the signal from a place where the driver can see you but you are not in danger yourself.

Do not confuse it with raising one arm above your head, which only acknowledges a driver's warning horn.

2. Calling the Signaller

To stop train movements on a line, a call must be made to the signaller using any lineside phone or a mobile phone (section 8.1). HB2 says you must try to contact the signaller in the quickest way . The equipment and steps below are for when the line must be protected, especially if the signaller cannot be reached.

3. Track Circuit Operating Clips

Track circuits and axle counters are two different ways of showing the signaller where trains are. A track circuit operating clip (TCOC) is clipped over the top of each running rail. On lines signalled by track circuits , this makes the signalling equipment detect a "train" and turns the nearest signal on the approach to danger. It has no effect where trains are detected by axle counters .

If you have one, your first step is to connect a track circuit operating clip between the two running rails of each affected line.

Do not use one where there is a fourth rail (four-rail DC areas).

In third-rail areas, attach the clip to the running rail furthest from the conductor rail first , then the nearest rail; remove it in the reverse order.

Once applied, a clip must not be removed until normal working can begin or other protection has been given, and you must get the signaller's permission before removing it.

A clip can be used only once . Give used clips to your supervisor.

4. Detonators

A detonator is a small explosive device clipped onto the rail head. When a train runs over it, it explodes with a loud bang to warn the driver.

Check the date of manufacture stamped on each detonator. Do not use any detonator older than five years , or one that is rusty, decayed or damaged; return it to your issuing point.

Place detonators 20 metres (about 20 yards or 65 feet) apart , in sets of three .

If you place them at a signal, put the first next to the signal and the other two beyond it.

If there is a third rail, place them on the running rail furthest from the conductor rail where possible.

Handle detonators carefully. When you have placed them, move at least 30 metres (about 100 feet) away and make sure nobody else goes near them. If you are staying near detonators that are not at a signal, stand at least 30 metres beyond them so the driver sees your hand danger signal after exploding them, with your back to the detonators to avoid the blast. OBSTRUCTION <-------------- 2 km (1 1/4 miles) --------------> [d]--20 m--[d]--20 m--[d]

  • (unsafe line) three detonators
  • |
  • stand at least 30 m away, show the
  • hand danger signal, back to detonators
  • direction trains approach from ------------------------------------------> (towards you)
  • 5. Full Detonator Protection

HB2 section 4 and the PTS handbook set out what to do when a line is obstructed or unsafe:

Place a track circuit operating clip , if available, on each affected line (except where there is a fourth rail).

Try to contact the signaller in the quickest way.

If you cannot contact the signaller , walk towards the direction trains can approach from, so that you can place three detonators, 20 metres apart, on each line concerned at 2 kilometres (1¼ miles) . This is called full detonator protection .

Show a hand danger signal to any train that approaches on the affected line.

Things You May Meet on the Way

A train approaches before you reach 2 kilometres : if it is safe to do so, immediately place three detonators on that line and show the hand danger signal, standing at least 30 metres from the detonators.

You reach a telephone linked to the signal box, or the signal box itself : place three detonators on the affected line, then speak to the signaller. If the signaller tells you the line is protected, you do not need to continue to the 2-kilometre point.

You reach a signal fitted with a signal post replacement switch (SPRS) : if you have a key and are competent to use it, operate the switch to put the signal to danger before placing three detonators, then speak to the signaller. Ask the signaller's permission before putting the signal back to automatic.

You reach a tunnel : place three detonators on the affected line at the tunnel entrance, try again to contact the signaller, and then, taking care of your own safety, continue through the tunnel. If the 2-kilometre point is inside the tunnel, walk to the far end and place three more detonators there.

You reach a junction : trains could approach from more than one direction. Place three detonators before the junction, decide which line a train is most likely to approach on, protect that line at 2 kilometres first, then go back and protect the other lines.

After Protection Is Provided

Unless told otherwise, stay near the detonators and keep showing the hand danger signal until someone else takes over or the line is protected in some other way.

Do not remove the protection until the line is safe again, or you are told that other protection is being given.

When protection is no longer needed, remove all the detonators and any track circuit operating clips , then tell the signaller, and give the used clips to your supervisor.

Loading diagram... Protecting an Unsafe Line (HB2 and RT3170)