Study guide

3.3 Procedures When a Train Approaches

Personal Track Safety PTS

Track your progress as you read

Finished sections get a check mark.

1 Introduction

About the PTS Qualification & Assessment

2 Chapter 1: Railway Infrastructure & Track Layout

1.1 Track Layout, Track Components & Permanent Way Terminology 1.2 Points, Crossings, Switch Blades & Associated Hazards 1.3 Limited Clearances, Refuges & Trackside Structures

3 Chapter 2: Sentinel Scheme, Fitness for Work & PPE

2.1 The Sentinel Scheme, Card System & Sponsorship 2.2 Medical Fitness, Drugs & Alcohol Policy & Fatigue Management 2.3 Trackside Personal Protective Equipment Standards

4 Chapter 3: Walking and Working On or Near the Line

3.1 On or Near the Line, the Lineside & Going onto the Railway 3.2 Positions of Safety, Walking Alone & Crossing the Line 3.3 Procedures When a Train Approaches

5 Chapter 4: AC Electrification & Overhead Line Safety

4.1 AC Overhead Line Equipment Principles & Components 4.2 AC Clearances, Live Equipment, Bonds & Overhead Line Permits 4.3 Overhead Line Emergencies, Emergency Switch-Off & Rescue

6 Chapter 5: DC Conductor Rail & Electrification Safety

5.1 DC Electrification Infrastructure & Operating Voltages 5.2 DC Working Distances, Safe Stepping & Bridging Risks 5.3 Flooding, Weather & DC Emergency Switch-Off

7 Chapter 6: Safe Systems of Work & Trackside Safety Roles

6.1 The Safe System of Work and Its Hierarchy 6.2 Trackside Safety Roles and How to Recognise Them 6.3 Briefings, During the Work & the Worksafe Procedure

8 Chapter 7: Safety-Critical Communications & Trackside Signage

7.1 Communicating Clearly: Safety-Critical Communications 7.2 Signals, Trackside Signs & Whistle Boards 7.3 Railway Telephones, Radio & Mobile Phones

9 Chapter 8: Railway Emergency Procedures & Stopping Trains

8.1 Emergencies: Danger to Trains and Emergency Calls 8.2 Stopping Trains and Protecting the Line 8.3 Reporting Your Concerns: Close Calls, CIRAS & Statutory Reporting

3.3 Procedures When a Train Approaches

Key Takeaways Explain This Topic AI

You must be in a position of safety at least 10 seconds before an approaching train passes.

Warning planning includes clearance, at least ten seconds in safety and every prescribed extra allowance; HB7’s current lookout restrictions also apply.

Raise one arm above your head to show the driver that you have heard the warning horn.

If a lookout gives the warning and you do not move, the lookout gives an urgent warning: a series of short sharp blasts on the whistle or horn.

If you cannot reach a position of safety, lie down but not in the four-foot, and gather loose clothing under you.

Last updated: October 2026

3.3 Procedures When a Train Approaches

Modern passenger and freight trains operate under strict physics. A passenger train travelling at 100 mph (160 km/h) covers approximately 45 metres every second and can need well over a kilometre to stop, even under emergency braking. A heavy freight train needs even further.

Train drivers cannot steer around track workers, nor can they stop in time if an individual stumbles across the rails. Consequently, the safety of track workers depends entirely on strict adherence to train approach warnings, rapid evacuation disciplines, and the rigorous enforcement of the mandatory 10-second rule under RSSB Rule Book Handbook 1 (GERT8000-HB1) .

  • Sighting Distance and Warning Time Principles
  • Current limits on lookout warning

HB7 Issue 10 section 6.8 permits lookout warning only when all its conditions are satisfied. No alternative safe system may be available, and the arrangement must be planned in advance and authorised at director level. The COSS must not act as lookout. The permissible speed of approaching trains must be no more than 25 mph , nobody may need to cross an open line to safety, and the group must not need to walk more than 25 metres along the line to reach safety. Required warning time must be no more than 45 seconds , while allowing everyone to reach safety at least 10 seconds before arrival.

Trains may approach only on the working line or an adjacent line; a train must not be able to route onto the relevant line after the lookout has seen it. Competent lookouts must be positioned for the required sighting and warnings in every applicable direction. They must have no other duties, take no part in the actual work and not be distracted. The warning must be heard by everyone, and tested before work. The system cannot be used if sighting, required staffing or the 45-second limit cannot be met. Do not use lookouts during darkness, poor visibility, or in or near a tunnel.

Working out warning time

The COSS considers stopping work, placing tools down and reaching safety, adds five seconds for each additional direction the site lookout watches , then adds at least ten seconds in the position of safety. Use HB7’s sighting chart and the applicable method; its warning-time aid also includes a five-second allowance when working alone. Chart speeds above 25 mph may be relevant to equipment warning ; they do not authorise a human-lookout system at those speeds.

For an illustrative group needing 15 seconds to stop and reach safety, with a lookout watching one additional direction, the subtotal is 15 + 5 + 10 = 30 seconds . That arithmetic alone authorises nothing: every condition above, sufficient sighting and the planned safe system must also be satisfied. A 90 mph human-lookout example does not comply with the current 25 mph restriction.

The Mandatory 10-Second Rule

The fundamental operational rule governing train approaches under RSSB Handbook 1 is the 10-second rule :

Important

Every person on or near the line must be standing stationary inside the designated Position of Safety at least 10 seconds before an approaching train reaches their location.

This 10-second buffer is non-negotiable for four vital safety reasons:

Human Error and Stumble Buffer : If a worker slips or stumbles on loose ballast while evacuating the track, the 10-second buffer provides time to recover and reach safety before impact.

Driver Assurance : Train drivers approaching a worksite at speed experience intense stress. Seeing personnel standing stationary in a position of safety 10 seconds out reassures the driver that the line is clear and prevents unwarranted emergency brake applications.

Turbulence Stabilization : It allows workers to plant their feet firmly and brace themselves before the train's bow-wave pressure and aerodynamic slipstream hit.

Group Accounting : It gives the COSS and lookouts time to check that every member of the group is clear of the line.

Step-by-Step Actions Upon Hearing the Warning

When a train approaches, a lookout gives the warning by whistle, horn or touch (shouting as well if necessary), or the sirens and lights of a warning system operate. The driver will also sound the train horn on seeing people on or near the line. +----------------------------------------------------------------------------------------+

  • | TRAIN APPROACH EVACUATION SEQUENCE |
  • | |
  • | [1. WARNING SOUNDED] ───► Lookout horn, LOWS siren, or approaching train horn |
  • | │ |
  • | ▼ |
  • | [2. STOP WORK] ───► Instantly cease all tasks; never finish the job |
  • | │ |
  • | ▼ |
  • | [3. PLACE TOOLS] ───► Lay tools flat in cess or clear of rails; never throw |
  • | │ |
  • | ▼ |
  • | [4. MOVE TO SAFETY] ───► Walk briskly to Position of Safety; reach it >= 10s before |
  • | │ |
  • | ▼ |
  • | [5. STAND & FACE] ───► Stand stationary, face approaching train, watch for hazards|
  • | │ |
  • | ▼ |
  • | [6. ACKNOWLEDGE] ───► If the driver sounds the horn, raise one arm above head |
  • +----------------------------------------------------------------------------------------+
  • Step 1: Immediately Stop Work

The instant the warning sounds, stop work immediately :

Never attempt to finish driving a screw, tightening a fishplate bolt, or taking one final measurement.

Do not hesitate or look around to see where the train is before reacting.

Immediate cessation of work is the difference between life and death.

Step 2: Put Down Tools Safely

Tools and equipment must be managed swiftly and deliberately:

Lay heavy power tools, impact wrenches, rail tongs, and ballast forks flat on the ground.

Ensure tools are placed completely clear of the running rails and outside the vehicle clearance envelope.

In third-rail electrified territory, never place metallic tools near conductor rails.

Never drop or throw tools, which can cause them to bounce onto the rail head or strike colleagues.

Secure loose lightweight items (such as surveying tape, plans, or bags) that could be sucked up by aerodynamic air currents.

HB1 says tools and equipment must not be placed closer than 2 metres (6 feet 6 inches) to a line on which a train could pass, unless you are absolutely sure they will not be hit by a passing train or moved by its slipstream.

Step 3: Move Directly to the Position of Safety

Move promptly along the pre-briefed evacuation path:

Walk briskly, deliberately, and carefully across the ballast shoulder.

Never run : Running on loose, uneven track ballast leads to twisted ankles, slips, and dangerous falls across the running rails.

Do not step on the rails or sleepers; walk ballast to ballast. On DC lines never step on a conductor rail or between a conductor rail and the adjacent running rail.

Conduct and Vigilance in the Position of Safety

Reaching the Position of Safety is not the end of the safety procedure. While the train is passing, workers must maintain active situational awareness.

Stand Still and Face the Approaching Train

Once inside the Position of Safety:

Stand stationary : Do not pace around, bend over, adjust boots, or rummage through toolbags.

Watch the train : Keep watching the train until it has passed you or you are certain it is not a danger to you. Never assume you know which line it is on, particularly if there are points nearby. +-----------------------------------------------------------------------------------------+

  • | HAZARDS TO MONITOR WHILE FACING PASSING TRAINS |
  • | |
  • | [PROJECTING LOADS] Flatbed wagons with shifted steel, timber, or unseated containers|
  • | [HANGING STRAPS] Loose curtain-side lorry straps, dangling lashing chains |
  • | [FLAPPING TARPAULINS] Heavy industrial tarpaulins unhooked from freight wagons |
  • | [FLYING BALLAST] Stones sucked from the track bed by aerodynamic bogie turbulence|
  • | [OPEN DOORS] Unlatched equipment hatches or malfunctioning exterior doors |
  • | [SUCTION FORCES] Low-pressure aerodynamic draw pulling you inward toward wheels |
  • +-----------------------------------------------------------------------------------------+
  • Hazards to Watch For During Train Passage

Facing the train allows you to spot dynamic mechanical hazards and react before they reach you:

Projecting and Shifted Freight : Freight wagons can suffer load shifts, causing structural steel, timber, or container boxes to protrude outward beyond the standard vehicle gauge.

Loose Rigging and Hanging Chains : Flapping tarpaulin sheets, dragging ropes, unhooked securing chains, or loose curtain-sided trailer straps can whip outward at 75 to 100 mph, acting like lethal scythes along the cess.

Flying Ballast and Debris : High-speed trains create powerful ground-level turbulence that can lift loose ballast stones, ice chunks in winter, or brake pad fragments, projecting them outward at extreme velocity.

Aerodynamic Slipstream Forces : The passage of train carriages creates a high-pressure bow wave at the front, followed immediately by severe low-pressure suction along the body panels and a violent trailing vortex at the rear. Standing firmly with feet braced prevents you from being pulled off balance toward the train bogies.

Acknowledging the Train Driver

When a train approaches a work group standing in a Position of Safety, effective safety-critical communication takes place between the track workers and the train driver. DRIVER SOUNDS THE WARNING HORN ───► WORKER IN POSITION OF SAFETY

  • O
  • /|\ <── raise ONE arm above
  • / \ your head: "I have
  • heard the warning"
  • The Acknowledgment Hand Signal

The Signal : When the driver sounds the warning horn, raise one arm above your head to show you have heard the warning (HB1 sections 3.1 and 4.4).

Meaning : The raised arm tells the driver that you have heard the warning. It is not a "clear" signal and it does not mean the driver will stop.

Do not confuse it with a danger signal : raising both arms above your head is the daylight hand danger signal used to stop a train in an emergency (section 8.2).

The Urgent / Continuous Horn Warning

If a train sounds a series of short blasts on the horn:

Warning

A series of short blasts is an urgent warning. The driver may believe someone is still in danger, and the PTS handbook warns that it can also mean the train could be moving in the wrong direction . Get to, or stay in, a position of safety immediately, check that everyone in your group is clear, and do not assume which line the train is on.

Lookout Warnings, Leaving the Position of Safety and Last Resorts

Lookout warnings : stop work, acknowledge the warning and move to the position of safety immediately. If someone does not acknowledge or move, the lookout gives an urgent warning: a series of short sharp blasts on the whistle or horn. Never distract a lookout.

Leaving the position of safety : when working under lookouts or a warning system, do not leave the position of safety until the COSS gives you permission . When alone, stay there until the train has passed clear or you are certain you will not be put in danger by that train or any other train.

Other trains : before leaving the position of safety, make sure no other trains have approached without you noticing.

Train in distress : a continuous series of long blasts on the high or loud tone means the driver has a problem; report it (HB1 section 7.6).

If you cannot reach a position of safety : the PTS handbook says lie down, but not in the four-foot , and gather loose clothing under you.

Loading diagram... Train Approach Procedure