Study guide
5.5 Provision and Use of Work Equipment Regulations 1998 (PUWER) & Equipment Inspections
CITB Site Management Safety Training Scheme SMSTS
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Legal Framework, CDM 2015 & Health and Safety Management
1.1 How the SMSTS Course and Examination Actually Work 1.2 Health and Safety at Work etc. Act 1974 (HASAWA) & Statutory Duties 1.3 Management of Health and Safety at Work Regulations 1999 & HSG65 (Plan-Do-Check-Act) 1.4 CDM 2015 Overview & Five Duty Holders (Client, Principal Designer, Principal Contractor, Designer, Contractor) 1.5 CDM 2015 Project Documentation: PCI, Construction Phase Plan & Health and Safety File 1.6 Statutory Notifications (F10), Enforcement Notices (Improvement/Prohibition), and Fee for Intervention (FFI) 1.7 RIDDOR 2013: Reporting Over-7-Day Injuries, Specified Injuries, Occupational Diseases & Dangerous Occurrences
2 Chapter 2: Risk Management, RAMS & Site Safety Leadership
2.1 Principles of Risk Assessment & Five Steps to Risk Assessment 2.2 Hierarchy of Control Measures & Risk Matrices 2.3 Developing, Reviewing, and Implementing Risk Assessments & Method Statements (RAMS) 2.4 Permit to Work (PTW) Systems for High-Risk Activities 2.5 Worker Consultation, Toolbox Talks, and Safety Leadership Culture 2.6 Behavioural Safety, Human Factors, and Accident Investigation Techniques
3 Chapter 3: High-Risk Site Operations: Height, Excavations & Confined Spaces
3.1 Work at Height Regulations 2005 & Hierarchy of Control for Height Work 3.2 Scaffolding Standards (TG20, BS EN 12811) & Statutory 7-Day Inspection Regimes 3.3 Mobile Elevating Work Platforms (MEWPs), Ladders, Tower Scaffolds & Fragile Roof Safety 3.4 Excavation Safety: Preventing Ground Collapse, Shoring, Battering & Edge Protection 3.5 Underground Services Avoidance (HSG47): Cable Avoidance Tools (CAT) & Genny Operation 3.6 Confined Spaces Regulations 1997: Risk Assessment, Atmosphere Testing & Rescue Procedures 3.7 Temporary Works Management: BS 5975-1, Coordinator Roles & Permits to Load and Strike
4 Chapter 4: Occupational Health, Chemical Safety & Physical Hazards
4.1 Control of Substances Hazardous to Health (COSHH) Regulations & Exposure Limits 4.2 Respirable Crystalline Silica (RCS), Dust Control & Respiratory Protective Equipment (RPE) 4.3 Asbestos Management on Construction Sites: Control of Asbestos Regulations 2012 4.4 Noise at Work Regulations 2005 & Hand-Arm Vibration Syndrome (HAVS) Exposure Action Values 4.5 Manual Handling Operations Regulations 1992, Ergonomics & Musculoskeletal Health 4.6 Health Surveillance, Medical Fitness & Workplace Hygiene/Wellbeing 4.7 Lead in Buildings: Control of Lead at Work Regulations 2002 & Blood-Lead Surveillance 4.8 Drugs and Alcohol at Work: Legal Framework, Site Policy, Testing & Support
5 Chapter 5: Fire Safety, Electrical Protection & Plant Operations
5.1 Fire Prevention on Construction Sites (HSG168), Fire Triangle & Hot Work Permits 5.2 Fire Extinguishers, Means of Escape, LPG Storage & Emergency Evacuation Plans 5.3 Electricity at Work Regulations 1989 & Safe Isolation Procedures 5.4 110V Reduced Low Voltage Systems, RCDs & Overhead Power Lines Safety (GS6) 5.5 Provision and Use of Work Equipment Regulations 1998 (PUWER) & Equipment Inspections 5.6 Lifting Operations and Lifting Equipment Regulations 1998 (LOLER), Crane Safety & Rigging
6 Chapter 6: Site Setup, Logistics, Welfare & Environmental Protection
6.1 CDM 2015 Schedule 2 Welfare Facilities Standards & Site Setup Requirements 6.2 Site Traffic Management, Pedestrian-Vehicle Segregation & Delivery Logistics 6.3 Site Inductions, Security, Signage & Competence Verification (CSCS/CPCS) 6.4 First Aid at Work Regulations 1981: Needs Assessment, First Aiders & Equipment 6.5 Environmental Protection: Waste Management (Duty of Care), Pollution Prevention & Noise Control 6.6 Mobile Workforce, Lone Working & Driving for Work
5.5 Provision and Use of Work Equipment Regulations 1998 (PUWER) & Equipment Inspections
Key Takeaways Explain This Topic AI
PUWER 1998 applies to all work equipment provided for use on site, requiring equipment to be suitable for intended purpose, safely maintained, and inspected at regular statutory intervals.
Equipment inspection regimes under Regulation 6 comprise Pre-Use Checks (daily/operator), Periodic Inspections (recorded weekly/monthly), and Exceptional Inspections (after major modifications, damage, or prolonged idle periods).
PUWER Regulation 9 mandates that only trained, competent, and authorized personnel (with certification such as CPCS/NPORS or manufacturer training) operate plant and machinery.
Machinery guarding (Regulation 11) follows a strict statutory hierarchy: fixed enclosed guards, interlocked guards, automatic guards, and trip devices (light curtains/pressure mats).
Mobile work equipment (PUWER Part III) requires Roll-Over Protective Structures (ROPS), Falling Object Protective Structures (FOPS), seatbelts, effective braking systems, and reverse alarms/cameras.
Last updated: August 2026
Provision and Use of Work Equipment Regulations 1998 (PUWER) & Equipment Inspections
Plant, machinery, power tools, and access equipment are central to construction operations, yet unmaintained or inappropriately used work equipment is a leading cause of severe site injuries, amputations, and fatalities. The Provision and Use of Work Equipment Regulations 1998 (PUWER) place broad, stringent legal duties on employers, site managers, and contractors to ensure that all work equipment provided on site is safe, suitable for its intended purpose, regularly inspected, and operated exclusively by competent personnel.
1. Scope and Core Requirements of PUWER 1998
PUWER applies to all "work equipment" provided for use in the workplace. The definition of work equipment is comprehensive, encompassing everything from simple hand tools (hammers, chisels), portable power tools (saws, drills), and access equipment (ladders, mobile towers) to heavy plant (excavators, dumpers, telehandlers) and workshop machinery.
Fundamental Employer Duties Under PUWER (Regulations 4–10)
Regulation Statutory Requirement Practical Construction Application
Regulation 4 Suitability: Equipment must be suitable for the specific task and environmental conditions. Providing 110V splash-proof outdoor power tools instead of 230V indoor tools on wet sites.
Regulation 5 Maintenance: Equipment must be maintained in an efficient state, efficient working order, and good repair. Establishing routine service schedules for excavators and maintaining a maintenance logbook.
Regulation 6 Inspection: Equipment must be inspected after installation, relocation, and at regular intervals by a competent person. Conducting daily pre-use operator checks and recorded weekly plant inspections.
Regulation 7 Specific Risks: Restricting use of equipment presenting high risks to designated, competent personnel. Limiting abrasive wheel operations exclusively to trained operatives holding certification.
Regulation 8 Information & Instructions: Providing operators with written health and safety manuals and user guides. Keeping plant operator manuals in the excavator cab and posting safety signs.
Regulation 9 Training: Ensuring all persons who use, manage, or supervise equipment have received adequate training. Verifying CPCS or NPORS operator cards prior to granting plant keys.
2. Statutory Inspection Regimes under PUWER Regulation 6
To ensure work equipment remains safe, PUWER Regulation 6 establishes a three-tier inspection regime: +-----------------------------------------------------------------------------------+
- | PUWER THREE-TIER INSPECTION REGIME |
- +-----------------------------------------------------------------------------------+
- | [ DAILY PRE-USE CHECK ] • Visual walkaround, oil/fluid checks, controls, |
- | (By Plant Operator) safety devices, tires, brakes, and warning lights. |
- | |
- | [ PERIODIC INSPECTION ] • Formal written technical inspection by competent |
- | (Weekly / Monthly) fitter; recorded in site Plant Inspection Register. |
- | |
- | [ EXCEPTIONAL CHECK ] • Triggered after major modifications, overturns, |
- | (Post-Event / Incident) accidents, or prolonged periods of site inactivity. |
- +-----------------------------------------------------------------------------------+
- 1. Pre-Use Checks (Daily)
Conducted by the operator at the start of every shift using a structured checklist. Includes checking fluid levels, hydraulic hoses, tires/tracks, seatbelts, lights, steering, braking systems, and emergency stops. Any safety-critical defect must result in immediate tagging out and removal of keys.
2. Periodic Inspections (Weekly / Monthly)
Detailed, documented technical inspections carried out by a competent plant technician. Results must be recorded in the site Work Equipment Register and retained on site for statutory inspection by HSE inspectors.
3. Exceptional Inspections
Mandatory inspections conducted whenever equipment is subjected to exceptional circumstances liable to jeopardize safety—such as after an overturn, structural impact, major repair, or extended storage.
3. Machinery Guarding Hierarchy (Regulation 11)
PUWER Regulation 11 requires employers to take effective measures to prevent access to dangerous parts of machinery or stop the movement of dangerous parts before access is gained. Regulation 11 sets out a strict statutory Guarding Hierarchy :
Fixed Enclosing Guards (First Choice): Physical guards attached by permanent means (welded) or fasteners (bolts, screws) that require tools for removal. Example: Fixed metal casing covering a table saw drive belt.
Other Physical Guards (Interlocked): Guards that physically prevent machine operation unless the guard is closed and locked. Opening the guard automatically cuts power to the dangerous drive mechanism.
Protection Devices: Sensors, trip devices, light curtains, or pressure-sensitive mats that bring moving parts to a complete stop before a worker can reach the hazard zone.
Information, Instruction, Training & PPE (Last Resort): Relying on push-sticks, warning notices, safety glasses, and operator caution. This tier is permissible ONLY where physical guards are proven technically impracticable.
4. Mobile Work Equipment Safety (PUWER Part III)
Mobile plant (dumpers, excavators, rollers, telehandlers) accounts for a high proportion of severe site incidents. PUWER Regulations 25 to 30 impose specific safety controls for mobile plant:
ROPS and FOPS Structures (Regulation 25 & 26)
Roll-Over Protective Structures (ROPS): Reinforced cab frames designed to preserve a survival space for the operator in the event of a plant overturn.
Falling Object Protective Structures (FOPS): Reinforced cab roofs designed to protect operators from falling masonry or materials.
Seatbelt Enforcement & Site Rules
"No Belt, No Operate": ROPS structures only protect operators if they remain inside the protective cab envelope during an overturn. Site managers must strictly enforce lap-belt compliance on forward tipping dumpers and excavators.
Visibility Aids & Pedestrian Segregation
360-Degree Visibility: Plant must be fitted with convex mirrors, 360-degree camera systems, and radar proximity sensors to eliminate blind spots around large excavators and dumpers.
Audible Warning Devices: Automatic white-noise reverse alarms and flashing beacons are mandatory on all site vehicles.
5. Controls, Isolation, and Emergency Stops (Regulations 14–18)
Control Systems: Operating controls must be clearly marked, accessible, and designed to prevent accidental actuation (e.g., shrouded start buttons or dead-man switches).
Emergency Stop Buttons (Regulation 18): Emergency stops must be clearly visible, easily reachable, and feature a red mushroom-head button mounted on a yellow background. Actuating an emergency stop must bring dangerous moving parts to a complete stop immediately without creating secondary hazards.