Study guide

4.2 Respirable Crystalline Silica (RCS), Dust Control & Respiratory Protective Equipment (RPE)

CITB Site Management Safety Training Scheme SMSTS

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Legal Framework, CDM 2015 & Health and Safety Management

1.1 How the SMSTS Course and Examination Actually Work 1.2 Health and Safety at Work etc. Act 1974 (HASAWA) & Statutory Duties 1.3 Management of Health and Safety at Work Regulations 1999 & HSG65 (Plan-Do-Check-Act) 1.4 CDM 2015 Overview & Five Duty Holders (Client, Principal Designer, Principal Contractor, Designer, Contractor) 1.5 CDM 2015 Project Documentation: PCI, Construction Phase Plan & Health and Safety File 1.6 Statutory Notifications (F10), Enforcement Notices (Improvement/Prohibition), and Fee for Intervention (FFI) 1.7 RIDDOR 2013: Reporting Over-7-Day Injuries, Specified Injuries, Occupational Diseases & Dangerous Occurrences

2 Chapter 2: Risk Management, RAMS & Site Safety Leadership

2.1 Principles of Risk Assessment & Five Steps to Risk Assessment 2.2 Hierarchy of Control Measures & Risk Matrices 2.3 Developing, Reviewing, and Implementing Risk Assessments & Method Statements (RAMS) 2.4 Permit to Work (PTW) Systems for High-Risk Activities 2.5 Worker Consultation, Toolbox Talks, and Safety Leadership Culture 2.6 Behavioural Safety, Human Factors, and Accident Investigation Techniques

3 Chapter 3: High-Risk Site Operations: Height, Excavations & Confined Spaces

3.1 Work at Height Regulations 2005 & Hierarchy of Control for Height Work 3.2 Scaffolding Standards (TG20, BS EN 12811) & Statutory 7-Day Inspection Regimes 3.3 Mobile Elevating Work Platforms (MEWPs), Ladders, Tower Scaffolds & Fragile Roof Safety 3.4 Excavation Safety: Preventing Ground Collapse, Shoring, Battering & Edge Protection 3.5 Underground Services Avoidance (HSG47): Cable Avoidance Tools (CAT) & Genny Operation 3.6 Confined Spaces Regulations 1997: Risk Assessment, Atmosphere Testing & Rescue Procedures 3.7 Temporary Works Management: BS 5975-1, Coordinator Roles & Permits to Load and Strike

4 Chapter 4: Occupational Health, Chemical Safety & Physical Hazards

4.1 Control of Substances Hazardous to Health (COSHH) Regulations & Exposure Limits 4.2 Respirable Crystalline Silica (RCS), Dust Control & Respiratory Protective Equipment (RPE) 4.3 Asbestos Management on Construction Sites: Control of Asbestos Regulations 2012 4.4 Noise at Work Regulations 2005 & Hand-Arm Vibration Syndrome (HAVS) Exposure Action Values 4.5 Manual Handling Operations Regulations 1992, Ergonomics & Musculoskeletal Health 4.6 Health Surveillance, Medical Fitness & Workplace Hygiene/Wellbeing 4.7 Lead in Buildings: Control of Lead at Work Regulations 2002 & Blood-Lead Surveillance 4.8 Drugs and Alcohol at Work: Legal Framework, Site Policy, Testing & Support

5 Chapter 5: Fire Safety, Electrical Protection & Plant Operations

5.1 Fire Prevention on Construction Sites (HSG168), Fire Triangle & Hot Work Permits 5.2 Fire Extinguishers, Means of Escape, LPG Storage & Emergency Evacuation Plans 5.3 Electricity at Work Regulations 1989 & Safe Isolation Procedures 5.4 110V Reduced Low Voltage Systems, RCDs & Overhead Power Lines Safety (GS6) 5.5 Provision and Use of Work Equipment Regulations 1998 (PUWER) & Equipment Inspections 5.6 Lifting Operations and Lifting Equipment Regulations 1998 (LOLER), Crane Safety & Rigging

6 Chapter 6: Site Setup, Logistics, Welfare & Environmental Protection

6.1 CDM 2015 Schedule 2 Welfare Facilities Standards & Site Setup Requirements 6.2 Site Traffic Management, Pedestrian-Vehicle Segregation & Delivery Logistics 6.3 Site Inductions, Security, Signage & Competence Verification (CSCS/CPCS) 6.4 First Aid at Work Regulations 1981: Needs Assessment, First Aiders & Equipment 6.5 Environmental Protection: Waste Management (Duty of Care), Pollution Prevention & Noise Control 6.6 Mobile Workforce, Lone Working & Driving for Work

4.2 Respirable Crystalline Silica (RCS), Dust Control & Respiratory Protective Equipment (RPE)

Key Takeaways Explain This Topic AI

Respirable Crystalline Silica (RCS) is the second leading cause of occupational cancer deaths in construction after asbestos, responsible for hundreds of UK worker fatalities annually.

The statutory Workplace Exposure Limit (WEL) for Respirable Crystalline Silica in the UK is strictly 0.1 mg/m³ as an 8-hour Time-Weighted Average (TWA).

Water suppression systems and M Class or H Class on-tool local exhaust ventilation (LEV) vacuums are mandatory engineering controls for cutting, chasing, grinding, or drilling silica-bearing materials.

Respiratory Protective Equipment (RPE) with an Assigned Protection Factor (APF) of at least 20 (such as an FFP3 mask) is required for high-dust silica activities as a secondary control.

Face fit testing (qualitative or quantitative) is a legal requirement for all tight-fitting RPE facepieces, and wearers must be clean-shaven to achieve an effective facial seal.

Last updated: August 2026

Understanding Respirable Crystalline Silica (RCS)

Crystalline Silica is a naturally occurring mineral present in vast quantities across common construction materials. It is found in quartz, sandstone, granite, concrete, mortar, tiles, bricks, slate, and paving slabs. The silica content varies significantly across different construction materials:

  • Sandstone: 70% to 90% crystalline silica
  • Concrete and Mortar: 25% to 70% crystalline silica
  • Bricks and Tiles: 30% to 60% crystalline silica
  • Granite: 20% to 45% crystalline silica
  • Limestone and Marble: 1% to 5% crystalline silica

When workers cut, grind, chase, drill, crush, or break down silica-containing materials using power tools, extremely fine dust particles are projected into the air. The finest fraction of this dust—particles smaller than 5 micrometers (µm) in diameter—is known as Respirable Crystalline Silica (RCS) . Unlike larger dust particles that are trapped by the upper respiratory tract and nose, RCS particles bypass the body's natural defenses and penetrate deep into the alveolar sacs of the lungs.

Health Risks and Pathological Impact of RCS

Exposure to Respirable Crystalline Silica is recognized by the Health and Safety Executive (HSE) as the second greatest occupational health hazard to UK construction workers, surpassed only by asbestos. Inhaled silica particles trigger severe, irreversible biological responses within lung tissues:

1. Silicosis

Silicosis is an irreversible, progressive, and incurable autoimmune lung disease. Inhaled RCS particles lodged in the alveoli are engulfed by lung macrophages, which die and trigger chronic inflammation and fibrotic scar tissue formation. Over time, lung tissue hardens and loses elasticity, severely impairing oxygen exchange.

Chronic Silicosis: Develops after 10 to 20 years of low to moderate RCS exposure.

Accelerated Silicosis: Develops within 5 to 10 years of intense exposure.

Acute Silicosis: Develops within weeks to months following massive, unmitigated exposure to high dust concentrations (e.g. dry sandblasting or enclosed concrete chasing without controls), leading to rapid, fatal respiratory failure.

2. Lung Cancer

Respirable Crystalline Silica is classified by the International Agency for Research on Cancer (IARC) as a Group 1 Human Carcinogen . Inhaling RCS directly increases the risk of developing malignant lung cancer, even in non-smokers.

3. Chronic Obstructive Pulmonary Disease (COPD)

Long-term exposure causes chronic bronchitis and emphysema, resulting in severe breathlessness, persistent coughing, and permanent loss of physical capacity.

Statutory Workplace Exposure Limit (WEL) for RCS

Under EH40 and COSHH, the statutory Workplace Exposure Limit (WEL) for Respirable Crystalline Silica is 0.1 mg/m³ calculated as an 8-hour Time-Weighted Average (TWA).

Because RCS is a classified carcinogen, COSHH Regulation 7 requires employers not only to keep airborne concentrations below 0.1 mg/m³, but to reduce exposure As Low As Reasonably Practicable (ALARP) . Dry cutting or dry chasing of concrete without engineering dust controls can generate airborne RCS concentrations exceeding 10 to 50 times the legal limit within seconds.

Engineering Control Measures: Water Suppression and Extraction

Site managers must enforce the HSE operational policy: Dry cutting, grinding, or chasing of silica-containing materials without dust suppression or extraction is unacceptable on construction sites.

1. Water Suppression Systems

Water suppression feeds a continuous stream of water directly onto the cutting blade or drill point, wetting dust particles at source and converting them into a slurry before they can become airborne.

Operational Rules: Water must be supplied at adequate pressure from a mains connection or pressurized container. Recirculated water systems must be filtered. Workers must manage slurry run-off to prevent slipping hazards and environmental pollution.

2. On-Tool Extraction (Local Exhaust Ventilation)

On-tool extraction systems capture dust directly at the point of generation using a specialized hood mounted on the power tool, connected via a flexible hose to a high-performance industrial vacuum extractor.

Dust Extraction Vacuum Classifications: M Class vs. H Class

Standard domestic or basic industrial vacuums must never be used for silica dust extraction because their filters allow respirable particles to pass straight through back into the room air. Vacuums used on construction sites are legally categorized under EN 60335-2-69 into three dust classes:

Dust Class Pass Threshold / Filter Efficiency Permissible Site Applications

L Class (Low Risk) Max pass 1.0% (99.0% efficiency) Softwood dust, general house-cleaning dusts with WEL > 1 mg/m³. Strictly forbidden for silica!

M Class (Medium Risk) Max pass 0.1% (99.9% efficiency) Mineral dusts, brick dust, concrete dust, mortar, tile dust, and silica dust with WEL ≥ 0.1 mg/m³. Minimum standard for general site silica dust extraction.

H Class (High Risk) Max pass 0.005% (99.995% efficiency) Highly carcinogenic dusts, asbestos dust, lead dust, mold spores, and toxic chemical dusts with WEL < 0.1 mg/m³. Recommended for high-volume indoor silica operations.

Site Management Standard: Site managers must verify that all dust extraction units attached to masonry saws, angle grinders, wall chasers, and SDS drills are certified to M Class as an absolute minimum, or H Class for enclosed/high-risk tasks.

Respiratory Protective Equipment (RPE) Selection and APF

Where engineering controls (water suppression or M-Class LEV) cannot reduce RCS exposure below the WEL or ALARP level, appropriate RPE must be provided as supplementary protection.

Assigned Protection Factor (APF)

The Assigned Protection Factor (APF) indicates the level of respiratory protection a clean-shaven wearer can expect to achieve. An APF of 20 means the respirator reduces the concentration of airborne contaminants reaching the user's lungs by a factor of 20 (i.e. reduces internal exposure to 1/20th of external air levels).

FFP3 Disposable Filtering Facepieces or P3 Half-Masks: Provide an APF of 20 . Required for high-dust silica activities such as concrete chasing, grinding, or cut-off saw operation.

FFP2 Respirators: Provide an APF of 10. Insufficient for high-volume silica cutting tasks.

Powered Air-Purifying Respirators (PAPR) with TH3 Filters: Provide an APF of 40 , delivering clean filtered air via a motorized fan to a full helmet or hood. Recommended for long-duration tasks or workers with facial hair (where tight-fitting seals cannot be achieved).

Mandatory Face Fit Testing Requirements

Under COSHH and HSE operational guidance INDG460 , face fit testing is a legal requirement for all tight-fitting respirator facepieces (including FFP1, FFP2, FFP3 disposable masks, half-masks, and full-face masks).

Fit Testing Protocols

Qualitative Fit Testing: Uses a bitter or sweet aerosol spray (Bitrex or Saccharin) inside a hood enclosure to test if the wearer can taste the chemical while performing standard facial movements.

Quantitative Fit Testing (e.g. PortaCount): Uses particle counting technology to measure the exact ratio of ambient dust particles outside the mask versus inside the mask to produce a numerical fit factor.

Critical Fit Testing Rules for Site Managers

Clean-Shaven Policy: Tight-fitting facepiece respirators rely on a critical seal against facial skin. Stubble, beards, or sideburns break this seal, allowing airborne silica dust to enter the mask. Workers must be clean-shaven in the facial seal area.

Re-testing Requirements: Fit testing must be repeated if the worker changes mask make/model, experiences significant weight changes, undergoes facial surgery, or develops facial scarring.

Competent Tester: Testing must be conducted by a competent fit tester (ideally accredited under the Fit2Fit scheme).

Maintenance, Storage, and Record Keeping for RPE

Site managers must ensure that reusable RPE is maintained in accordance with statutory requirements:

RPE must be stored in a clean, dry, designated storage box away from dust, direct sunlight, and chemicals.

Monthly visual inspections and functional checks must be performed on reusable respirators.

RPE inspection and maintenance records must be retained for a minimum of 5 years .