Study guide

5.3 Dead-Reckoning Plots & Estimated Positions

USCG OUPV Six-Pack Captain License Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction: Getting Your OUPV License

0.1 About the OUPV / Six-Pack License 0.2 Eligibility & Sea Service Requirements 0.3 Credentialing: MMC Application, TWIC, Physical, Drug Test & CPR 0.4 Exam Format, Modules, Scoring & Testing Logistics

2 Rules of the Road (Navigation Rules)

1.1 The Navigation Rules: International (COLREGS) vs Inland 1.2 General Definitions (Rules 1-3) 1.3 The Lookout & Safe Speed (Rules 5-6) 1.4 Risk of Collision & Compass Bearings (Rule 7) 1.5 Action to Avoid Collision (Rule 8) 1.6 Narrow Channels & Traffic Separation Schemes (Rules 9-10) 1.7 Overtaking (Rules 11-13) 1.8 Head-On & Crossing Situations (Rules 14-15) 1.9 Give-Way & Stand-On Responsibilities (Rules 16-17) 1.10 Responsibilities Between Vessels — the Pecking Order (Rule 18) 1.11 Conduct in Restricted Visibility (Rule 19) 1.12 Lights & Shapes — General Rules, Visibility & Definitions (Rules 20–22) 1.13 Lights for Power-Driven Vessels Underway (Rule 23) 1.14 Lights & Shapes for Towing and Pushing (Rule 24) 1.15 Lights for Sailing, Rowing & Fishing Vessels (Rules 25–26) 1.16 Lights & Shapes for NUC, RAM, CBD, Pilot, Anchored & Aground (Rules 27–30) 1.17 Sound & Light Signals + Distress Signals (Rules 32–37, Annex IV)

3 Navigation General

2.1 Nautical Charts: Reading, Scale, Lat/Long & Chart No. 1 2.2 The U.S. Aids to Navigation System: Lateral Marks (IALA Region B) 2.3 Non-Lateral Aids: Safe-Water, Isolated-Danger, Special & Information Marks 2.4 Light Characteristics & Buoy Numbering 2.5 The Magnetic Compass: Variation & Deviation 2.6 Compass Error & Conversions (TVMDC) 2.7 Piloting: Bearings, Lines of Position & Fixes 2.8 Dead Reckoning: Speed-Time-Distance 2.9 Tides: Tables, Datums & Height of Tide 2.10 Currents: Set, Drift & Current Tables 2.11 Navigation Publications 2.12 Marine Weather & Meteorology 2.13 Storm Warnings & Heavy-Weather Handling 2.14 Electronic Navigation: GPS, Chartplotters, Depth Sounder & AIS 2.15 Radar & Marine Radio (VHF / GMDSS)

4 Deck General: Seamanship & Vessel Operations

3.1 Vessel Nomenclature & Construction Terms 3.2 Marlinespike Seamanship: Lines, Knots & Splices 3.3 Ground Tackle & Anchoring 3.4 Boat Handling & Maneuvering 3.5 Docking, Undocking & Line Handling 3.6 Marine Engines, Fuel & Basic Troubleshooting 3.7 Vessel Documentation, Load Lines & Regulations 3.8 Marine Environmental Protection & Pollution Regulations

5 Deck Safety: Emergencies, Firefighting & Survival

4.1 Required Safety Equipment & Carriage Regulations 4.2 Personal Flotation Devices & Lifesaving Appliances 4.3 Fire Prevention & the Fire Triangle 4.4 Firefighting Equipment & Procedures 4.5 Man Overboard & Recovery 4.6 Flooding, Damage Control & Abandon Ship 4.7 Vessel Stability & Loading 4.8 First Aid, Survival & Cold-Water Immersion

6 Chart Plotting & Navigation Problems

5.1 Plotting Tools & Chart Setup 5.2 Plotting Courses, Bearings & Measuring Distance 5.3 Dead-Reckoning Plots & Estimated Positions 5.4 Fixes: Two/Three-Bearing, Running Fix & Distance-Off 5.5 Set, Drift & Course-to-Steer Problems

5.3 Dead-Reckoning Plots & Estimated Positions

Key Takeaways Explain This Topic AI

A DR plot projects position from the last fix using only course steered and speed; it ignores current, wind, and steering error and must be checked against fixes.

Label the true course above the line and speed below, and mark a DR position (semicircle + time) at every course change, speed change, fix, and hour.

Advance or retard a DR with 60 D = S T: at 10 knots a 30-minute leg is 5.0 nm, laid off along the new course from the turn point.

Correct a DR for a known current to get an estimated position (square): shift the DR by set (direction) a distance of drift times time.

With only one line of position, the best estimate is the foot of the perpendicular from the DR to that LOP, marked as an EP.

Last updated: July 2026

What a DR Plot Shows

A dead-reckoning (DR) plot projects your position forward from your last fix using only the course steered and the speed (or distance run). It deliberately ignores current, wind, and steering error, so it answers "where should I be?" — an estimate to be checked against the next fix. The engine is the same 60 × D = S × T relationship from Chapter 2; here we focus on drawing and labeling the track.

Building the Track

Start at your last fix (circle + time).

Draw the course line in the true direction steered; label C 075°T above the line and S 10 below it.

Wherever anything changes — a new course, a new speed, a fix, or simply the top of the hour — mark a DR position with a semicircle and the four-digit time.

Worked example — plotting DR positions. You take a 0800 fix, then steer C 075°T at S 10 . Where are the 0900 and 0930 DR positions?

To 0900 (60 min): D = (S × T)/60 = (10 × 60)/60 = 10.0 nm .

To 0930 (90 min): D = (10 × 90)/60 = 15.0 nm .

Step off 10.0 nm and 15.0 nm along the 075°T line with your dividers and mark each with a semicircle and time.

Advancing (and Retarding) a Position

Because DR is time-based you can advance a position forward or retard it back with the same arithmetic.

Worked example — a course change. At 0930 you alter course to C 120°T , still at 10 knots . Where is the 1000 DR? That is 30 minutes : D = (10 × 30)/60 = 5.0 nm . From the 0930 DR position, lay off 5.0 nm along 120°T and mark the 1000 DR. The track now has a "kink" at 0930 where you turned — DR always follows the actual sequence of courses and speeds.

Retarding a position works the same arithmetic backward. If you want the DR for 1000 but only plotted a position at 1015 , back off the distance run in those 15 minutes — at 10 knots, (10 × 15)/60 = 2.5 nm — along the reverse of the course to find the earlier point.

The Three Positions Compared

  • Position Built from Symbol
  • DR Course steered + speed/time only Semicircle
  • EP DR corrected for known current Square
  • Fix Two or more crossing LOPs Circle

Each is a better estimate than the one above it: a fix beats an EP, which beats a bare DR.

When to Plot a DR Position

Prudent practice — and the convention the exam expects — is to lay down a new DR position at four moments: every time you change course, every time you change speed, every time you take a fix, and at every whole hour. Plotting on these events keeps the track honest and gives you ready reference points if a question asks "where were you at 0930?" A DR carried too far without a checkpoint invites arithmetic slips and leaves nothing to reset against when the next fix arrives. On a timed plotting problem, marking the hourly and turn positions also earns the partial-credit checkpoints graders look for.

From DR to Estimated Position

A DR position ignores current. When you know a current is running, apply it to the DR to get an estimated position (EP) , marked with a square . You shift the DR by the current's set (direction) a distance equal to drift × time .

Worked example — DR corrected for current. From the 0900 DR position you know a current has been setting 180°T (due south) at 1.5 knots for the past hour. Over 1 hour the current carries you 1.5 nm in direction 180°T . Shift the 0900 DR 1.5 nm due south and mark that point with a square — that is your 0900 EP , a better estimate of where you truly are than the raw DR.

Estimated Position From a Single LOP

If you get only one bearing — a single line of position — you cannot fix your position, but you can improve the DR. The best estimate is the point on the LOP nearest the DR position : drop a perpendicular from the DR to the LOP , and mark the foot of that perpendicular as an EP (square) with the time. It uses the one piece of real information you have (you are somewhere on that line) without pretending to a full fix.

Symbol and Method Traps

Mixing the symbols. DR = semicircle , fix = circle , EP = square . Graders check these.

Not restarting DR from each new fix. Every fix resets the accumulated DR error; carry the DR forward from the fix, not from the old DR.

Applying current twice — once as an EP and again as a "corrected DR." The current adjustment turns a DR into an EP; it is applied once.

Forgetting the hourly/turn marks , which leaves the plot unreadable and costs partial-credit checkpoints.