Study guide
5.2 Plotting Courses, Bearings & Measuring Distance
USCG OUPV Six-Pack Captain License Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction: Getting Your OUPV License
0.1 About the OUPV / Six-Pack License 0.2 Eligibility & Sea Service Requirements 0.3 Credentialing: MMC Application, TWIC, Physical, Drug Test & CPR 0.4 Exam Format, Modules, Scoring & Testing Logistics
2 Rules of the Road (Navigation Rules)
1.1 The Navigation Rules: International (COLREGS) vs Inland 1.2 General Definitions (Rules 1-3) 1.3 The Lookout & Safe Speed (Rules 5-6) 1.4 Risk of Collision & Compass Bearings (Rule 7) 1.5 Action to Avoid Collision (Rule 8) 1.6 Narrow Channels & Traffic Separation Schemes (Rules 9-10) 1.7 Overtaking (Rules 11-13) 1.8 Head-On & Crossing Situations (Rules 14-15) 1.9 Give-Way & Stand-On Responsibilities (Rules 16-17) 1.10 Responsibilities Between Vessels — the Pecking Order (Rule 18) 1.11 Conduct in Restricted Visibility (Rule 19) 1.12 Lights & Shapes — General Rules, Visibility & Definitions (Rules 20–22) 1.13 Lights for Power-Driven Vessels Underway (Rule 23) 1.14 Lights & Shapes for Towing and Pushing (Rule 24) 1.15 Lights for Sailing, Rowing & Fishing Vessels (Rules 25–26) 1.16 Lights & Shapes for NUC, RAM, CBD, Pilot, Anchored & Aground (Rules 27–30) 1.17 Sound & Light Signals + Distress Signals (Rules 32–37, Annex IV)
3 Navigation General
2.1 Nautical Charts: Reading, Scale, Lat/Long & Chart No. 1 2.2 The U.S. Aids to Navigation System: Lateral Marks (IALA Region B) 2.3 Non-Lateral Aids: Safe-Water, Isolated-Danger, Special & Information Marks 2.4 Light Characteristics & Buoy Numbering 2.5 The Magnetic Compass: Variation & Deviation 2.6 Compass Error & Conversions (TVMDC) 2.7 Piloting: Bearings, Lines of Position & Fixes 2.8 Dead Reckoning: Speed-Time-Distance 2.9 Tides: Tables, Datums & Height of Tide 2.10 Currents: Set, Drift & Current Tables 2.11 Navigation Publications 2.12 Marine Weather & Meteorology 2.13 Storm Warnings & Heavy-Weather Handling 2.14 Electronic Navigation: GPS, Chartplotters, Depth Sounder & AIS 2.15 Radar & Marine Radio (VHF / GMDSS)
4 Deck General: Seamanship & Vessel Operations
3.1 Vessel Nomenclature & Construction Terms 3.2 Marlinespike Seamanship: Lines, Knots & Splices 3.3 Ground Tackle & Anchoring 3.4 Boat Handling & Maneuvering 3.5 Docking, Undocking & Line Handling 3.6 Marine Engines, Fuel & Basic Troubleshooting 3.7 Vessel Documentation, Load Lines & Regulations 3.8 Marine Environmental Protection & Pollution Regulations
5 Deck Safety: Emergencies, Firefighting & Survival
4.1 Required Safety Equipment & Carriage Regulations 4.2 Personal Flotation Devices & Lifesaving Appliances 4.3 Fire Prevention & the Fire Triangle 4.4 Firefighting Equipment & Procedures 4.5 Man Overboard & Recovery 4.6 Flooding, Damage Control & Abandon Ship 4.7 Vessel Stability & Loading 4.8 First Aid, Survival & Cold-Water Immersion
6 Chart Plotting & Navigation Problems
5.1 Plotting Tools & Chart Setup 5.2 Plotting Courses, Bearings & Measuring Distance 5.3 Dead-Reckoning Plots & Estimated Positions 5.4 Fixes: Two/Three-Bearing, Running Fix & Distance-Off 5.5 Set, Drift & Course-to-Steer Problems
5.2 Plotting Courses, Bearings & Measuring Distance
Key Takeaways Explain This Topic AI
Lay off a course by setting parallel rules through both points and walking to the rose; read the outer ring for the true course and its reciprocal.
Measure distance only on the latitude scale at the same latitude as your track, because 1' of latitude = 1 nautical mile; never use the longitude scale on a Mercator chart.
The chart is true; convert true to compass with TVMDC (down the ladder = add West, subtract East), or read magnetic off the rose's inner ring and apply only deviation.
Combined problem: 085 T with 8 W variation and 2 E deviation gives a compass course of 091; 18 nm at 12 kn takes 90 minutes, so departing 0910 the ETA is 1040.
Plot an observed bearing by converting it to true, then drawing the line of position outward from the charted object.
Last updated: July 2026
Laying Off a Course Between Two Points
To find the course from your position to a destination — say from buoy R"2" to a harbor entrance — set one edge of the parallel rules through both points , then walk the rules to the nearest compass rose center and read the direction. The number pointing toward the destination is your course; the number 180° away is its reciprocal. Read the outer ring for a true course, which is what you draw and label on the chart ( C 085°T ).
Measuring Distance — Latitude Scale Only
Set your dividers with one point on each end of the leg, carry that spread to the latitude scale on the left or right side of the chart, and read the nautical miles — because 1 minute of latitude equals 1 nautical mile . Read the scale at roughly the same latitude as your track , since a Mercator chart's scale stretches toward the poles. For a long leg, open the dividers to a round number (5 or 10 nm), step along the course line, and add up the steps plus the remainder.
Never measure distance on the longitude scale across the top or bottom — on a Mercator chart a minute of longitude is not a nautical mile.
Worked example — stepping a long leg. A leg measures longer than your dividers can span. Open the dividers to 10 nm on the latitude scale, step along the course line three full steps ( 30 nm ), then close them onto the leftover and read 7 nm on the scale. The leg is 30 + 7 = 37 nautical miles. Stepping keeps a long measurement accurate where a single wide, sagging divider span would not.
True vs. Magnetic Plots
The chart is a true world: courses and bearings you draw are true. To actually steer a course you must convert true → compass with the TVMDC ladder from Chapter 2 (going down: add West, subtract East ). A shortcut is to read directions off the rose's inner (magnetic) ring , which already includes variation, and then apply only deviation to reach the compass course.
Worked example A — reading magnetic directly. You lay off a course and read 120°T on the outer ring. On the inner ring of a rose whose variation is 15°W , the same line reads 135°M . Check with TVMDC: True → Magnetic adds westerly variation, 120° + 15° = 135°M . The inner ring did the arithmetic for you.
Capstone Worked Problem — Compass Course and ETA
This is the classic combined question the module loves:
You depart buoy R"2" at 0910 . From the chart you measure the course to buoy G"5" as 085°T and the distance as 18 nautical miles . Variation at the nearest rose is 8°W , your vessel's deviation on this heading is 2°E , and you make 12 knots . What compass course do you steer, and what is your ETA at G"5"?
Step 1 — compass course (TVMDC, going down, add West / subtract East):
- Step Value Result
- True (T) 085° 085°
- Variation 8°W +8 (add West) Magnetic = 093°
- Deviation 2°E −2 (subtract East) Compass = 091°
Steer 091° by compass.
Step 2 — ETA (60 × D = S × T):
T = (60 × D) / S = (60 × 18) / 12 = 90 minutes = 1 h 30 m .
Depart 0910 + 1:30 = ETA 1040 .
So the single answer is: steer 091°, arrive 1040. Notice the westerly variation pushed the number up 8°, and the easterly deviation pulled it back down 2°.
Plotting a Bearing as a Line of Position
To plot a bearing you observe to a charted object: take the bearing with a hand-bearing compass (it reads magnetic/compass), convert it to true , set the parallel rules to that true bearing at the rose, walk to the object , and draw the line from the object toward your side of it. You lie somewhere on that line of position (LOP) — specifically on the near side , in the reciprocal direction, since the bearing points toward the object. Two such lines crossing give a fix (Section 5.4).
Ranges — the Most Precise LOP
When two charted objects line up visually — a front and rear beacon, or a light behind a buoy — you are exactly on the straight range line through both, with no compass reading required. A range is the most accurate line of position available and is worth watching for whenever the problem places two objects in transit. The reciprocal discipline matters everywhere: the course to your destination is 180° from the course measured from it, and a bearing to an object is the reciprocal of the LOP direction you draw from it. Fixing which end of the line you mean before you read the rose prevents a 180° blunder.
Traps in Course and Distance Work
Measuring on the longitude scale — the number-one distance error.
Plotting a magnetic bearing as if it were true — always convert first.
Confusing the course with its reciprocal — the direction to the destination, not from it.
Reading the scale at the wrong latitude on a long north–south chart, where the scale visibly changes.