Study guide

Section 7.3: Part Assembly & Mechanical Drawing

USPS Postal Exam 955 Technical Maintenance

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 USPS 955 Exam Structure & Scoring 1.2 Personal Characteristics & Experience Inventory 1.3 PSI Testing & Multicraft Test Strategy

2 Chapter 2: Electronics

Section 2.1: Digital Logic Gates & Truth Tables Section 2.2: Combinational & Sequential Logic Section 2.3: Analog Electronic Devices Section 2.4: Operational Amplifiers (Op-amps) & Filters Section 2.5: Power Supplies & Rectification Section 2.6: Electronic Schematic & Symbol Reading

3 Chapter 3: Electrical Fundamentals

Section 3.1: Ohm's Law & Circuit Calculations Section 3.2: Capacitance, Inductance & RC/RL Networks Section 3.3: AC & DC Power Fundamentals Section 3.4: Three-Phase Power & Motors

4 Chapter 4: Mechanical Systems

Section 4.1: Power Transmission & Machine Elements Section 4.2: Bearings & Lubrication Section 4.3: Hydraulic Principles & Components Section 4.4: Pneumatic Principles & Components

5 Chapter 5: HVAC & Refrigeration

Section 5.1: The Refrigeration Cycle Section 5.2: Refrigerants & Environmental Controls Section 5.3: Heating & Combustion Systems Section 5.4: HVAC Control Systems

6 Chapter 6: Computers, PLCs & Networking

Section 6.1: PC Hardware & Operating Systems Section 6.2: Industrial Networks & Cabling Section 6.3: PLC Fundamentals & I/O Systems Section 6.4: PLC Troubleshooting & Ladder Logic

7 Chapter 7: Spatial Reasoning

Section 7.1: Object Rotation & 3D Visualization Section 7.2: Paper Folding & Pattern Matching Section 7.3: Part Assembly & Mechanical Drawing Section 7.4: Spatial Visualization Strategies

8 Chapter 8: Mathematical Reasoning

Section 8.1: Applied Algebra & Formulas Section 8.2: Geometric Formulas & Measurement Section 8.3: Unit Conversions & Scale Section 8.4: Readout & Indicator Problems

9 Chapter 9: Industrial Safety & Standards

9.1 Lockout/Tagout (LOTO) Procedures 9.2 Electrical Safety & NFPA 70E 9.3 Workplace Hazards, PPE & SDS 9.4 Safe Tool Usage & Material Handling

Section 7.3: Part Assembly & Mechanical Drawing

Key Takeaways Explain This Topic AI

Part assembly requires mentally joining separate shapes along mating features like slots or pegs.

Exploded views illustrate components separated but aligned along centerlines to show assembly order.

Orthographic projections show 2D views (front, top, side) using third-angle projection in the US.

Last updated: July 2026

Part Assembly & Mechanical Drawing

In the industrial maintenance environment of the United States Postal Service ( USPS ), the ability to read technical drawings and assemble components correctly is paramount. Section 7.3 covers part assembly and mechanical drawing interpretation, which are critical components of the USPS Exam 955. These questions assess your ability to visualize how individual, disassembled parts fit together to form a completed unit, as well as your understanding of standard engineering drawing conventions, such as orthographic projections, isometric views, and exploded assemblies.

Part Assembly

Part Assembly problems present you with several separate 2D or 3D shapes. You must mentally manipulate and join these parts along their mating edges to determine the final assembled shape.

To solve part assembly tasks efficiently, employ the following strategies:

Match Mating Features : Look for unique slots, tabs, pegs, or angled cuts. A triangular peg on one part must fit into a corresponding triangular slot on another.

Conserve Volume and Surface Area : The total volume of the assembled object must equal the sum of the volumes of the individual components. Be suspicious of options that appear significantly larger or smaller than the combined parts.

Analyze Angles : Pay close attention to joint angles. If two parts meet at a 90-degree angle, the resulting assembly must reflect that perpendicular relationship.

Exploded Views

An Exploded View is a technical drawing that shows the individual components of an assembly separated from one another, but positioned to show their relationship and order of assembly. These drawings are widely used in maintenance manuals, parts catalogs, and bills of materials ( BOM ).

On the exam, you may be asked to identify the correct sequence of assembly or determine how specific components interact when fully assembled. To read these drawings:

Follow the Centerlines : Exploded views use thin, dashed alignment lines to show how parts align and slide together during assembly.

Identify Fasteners: Note the locations of bolts, pins, and keys, as these indicate how components are secured to one another.

Understand Layering: Recognize the order of assembly. Washers must be placed before nuts, and gaskets must be sandwiched between mating surfaces.

Orthographic Projections & Glass Box Method

Orthographic Projection is a method of representing a 3D object in 2D by projecting its views onto perpendicular planes. In the United States, engineering drawings typically use Third-Angle Projection , which organizes views as if you were looking through the faces of a transparent box surrounding the object—a concept known as the Glass Box Method .

The standard orthographic drawing includes three primary views:

Front View : The primary view showing the most detail and width/height.

Top View : Positioned directly above the front view, showing width/depth.

Right-Side View : Positioned to the right of the front view, showing height/depth.

When interpreting orthographic drawings, you must understand the meaning of line types. Continuous solid lines represent visible edges, while dashed lines represent Hidden Lines (features that are not visible from the current perspective, such as internal holes or recesses).

  • View Name Dimensions Shown Relative Position in Third-Angle Purpose
  • Front View Width and Height Center / Reference View Shows primary shape and layout
  • Top View Width and Depth Directly above Front View Shows layout of top-facing features
  • Right-Side View Depth and Height To the right of Front View Shows profile and vertical steps
  • Isometric & Pictorial Drawings

An Isometric Drawing is a type of 3D pictorial drawing where the three spatial axes appear equally foreshortened. The angles between the projections of the X, Y, and Z axes are all equal to 120 degrees. This drawing style allows a technician to quickly understand the 3D form of an object without needing to interpret multiple 2D views.

Unlike perspective drawings, isometric drawings do not have vanishing points. Parallel lines on the physical object remain parallel in the drawing. This lack of Foreshortening makes it easier to measure dimensions directly from the drawing, though it can create minor visual distortion for very large objects.

Applications in Postal Facility Maintenance

Maintenance personnel frequently use these drawing skills when servicing automated systems. For example, during a rebuild of a Delivery Bar Code Sorter ( DBCS ) gate assembly, a technician must refer to exploded views in the maintenance handbook to identify part numbers, order replacements, and reassemble the unit in the correct sequence.

Additionally, understanding orthographic projections is vital when reading electrical and mechanical schematics. When troubleshooting a pneumatic cylinder or a motor drive shaft, the technician must look at the orthographic views to locate the physical position of internal bearings, seals, and keyways. A solid command of mechanical drawing conventions prevents assembly errors that could lead to immediate mechanical failure upon power-up.