Study guide
4.2 Dwelling Load Calculations — Standard Method (Article 220 Part III)
Virginia Journeyman Electrician Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 Exam Facts, Format & Scoring 1.2 Eligibility, Application & Scheduling 1.3 Open-Book Strategy & Test-Taking
2 Virginia Board Regulations (18VAC50-30)
2.1 Definitions & Qualification for Licensure 2.2 Standards of Practice 2.3 Standards of Conduct & Revocation of Licensure 2.4 Renewal and Reinstatement
3 General Knowledge & Electrical Fundamentals
3.1 General Electrical Knowledge 3.2 Requirements for Electrical Installations (Article 110) 3.3 Electrical-Electronic Fundamentals & Theory
4 Branch Circuits & Load Calculations
4.1 Branch Circuit Requirements (Article 210) 4.2 Dwelling Load Calculations — Standard Method (Article 220 Part III) 4.3 Commercial & Multifamily Load Calculations (Article 220 Part III) 4.4 Neutral Loads & Optional Calculation Methods
5 Services & Feeders
5.1 Service Entrance Requirements (Article 230) 5.2 Feeder Requirements (Article 215) 5.3 Service & Feeder Sizing Calculations
6 Grounding & Bonding
6.1 Grounding Electrode Systems (Article 250 Part II) 6.2 Grounded Conductors & System Bonding (Article 250 Parts III-IV) 6.3 Equipment Grounding & Bonding (Article 250 Parts V-VIII) 6.4 Separately Derived Systems & Special Grounding
7 Conductors & Cables
7.1 Conductor Ampacity (Table 310.16) 7.2 Temperature Correction & Adjustment Factors (310.14/310.15) 7.3 Conductor Selection, Insulation & Parallel Conductors 7.4 Cable Types & Applications (NM, AC, MC, UF, SE)
8 Raceways & Boxes
8.1 Raceway Types & Selection (Articles 342-366) 8.2 Conduit Fill & Raceway Sizing (Chapter 9 Tables) 8.3 Box Sizing & Fill (Article 314) 8.4 Pull Boxes, Junction Boxes & Conduit Bodies
9 Motors, Transformers & Controls
9.1 Motor Branch Circuits & Short-Circuit Protection (Article 430 Part IV) 9.2 Motor Overload Protection (Article 430 Part III) 9.3 Motor Controllers, Circuits & Disconnects (Article 430 Parts II, VII, IX) 9.4 Transformers (Article 450)
10 Special Occupancies, Equipment & Signs
10.1 Hazardous (Classified) Locations (Article 500) 10.2 Garages, Bulk Storage, Health Care & Other Special Occupancies 10.3 Special Equipment (Pools, Industrial Machinery, Selected) 10.4 Electrical Signs & Outline Lighting (Article 600)
11 Utilization Equipment, Lighting & Low-Voltage
11.1 Utilization Equipment (Article 422) 11.2 Lighting & Luminaires (Article 410) 11.3 General Low Voltage Requirements (Article 725) 11.4 Communication Systems (Article 800) 11.5 Fire Detection & Alarm Systems (Article 760)
12 Electrical Safety
12.1 Shock Hazards & Safe Work Practices 12.2 Arc-Flash Hazards & NFPA 70E 12.3 Lockout/Tagout, PPE & Approach Boundaries
4.2 Dwelling Load Calculations — Standard Method (Article 220 Part III)
Key Takeaways Explain This Topic AI
Dwelling general lighting load = 3 VA/sq ft [220.14(J)]; add two 1500 VA small-appliance circuits [220.52(A)] and one 1500 VA laundry circuit [220.52(B)] before applying demand factors.
Table 220.42 demand factors for dwellings: first 3000 VA at 100%, remainder from 3001-120000 VA at 35%, over 120000 VA at 25%.
Electric clothes dryers use 5000 VA or nameplate, whichever is larger [220.54]; ranges 8¾-12 kW use 8 kW demand from Table 220.55 Column C, with a 5% per kW increase above 12 kW.
The 75% demand factor in 220.53 applies to four or more fastened-in-place appliances but excludes dryers, ranges, space heating, and A/C.
A 2000 sq ft dwelling with a 12 kW range and 5 kW dryer calculates to a service load of approximately 95 A on a 120/240V single-phase service using the standard method.
Last updated: August 2026
General Lighting Load (220.14(J))
For dwelling units, NEC 220.14(J) sets the general lighting/receptacle load at 3 VA per square foot , computed from the building's outside dimensions. Exclude open porches, garages, and unfinished spaces not adaptable for future use.
Small-Appliance and Laundry Circuits (220.52)
Add to the general lighting load before applying demand factors:
Two small-appliance branch circuits at 1500 VA each = 3000 VA [ 220.52(A) ].
One laundry branch circuit at 1500 VA [ 220.52(B) ].
These are minimums — you may install more, but the calculation uses these values.
Table 220.42 Demand Factors (Dwellings)
Apply Table 220.42 to the combined general lighting + small-appliance + laundry load:
- Portion of Load (VA) Demand Factor
- First 3000 VA or less 100%
- 3001-120,000 VA 35%
- Over 120,000 VA 25%
The 35% tier is the most-tested breakpoint. Always subtract the first 3000 VA before applying 35%.
- Appliances — Dryer, Range, Fixed
- Electric Clothes Dryers (220.54)
Load per dryer = 5000 VA or nameplate, whichever is larger [ 220.54 ]. For five or more dryers , Table 220.54 demand factors apply (e.g., 5 dryers = 75%, decreasing to 25% for 43+ dryers).
Household Ranges (220.55, Table 220.55)
For ranges 8¾ kW through 12 kW, Table 220.55 Column C demand is 8 kW for one range . Note 1 : for ranges over 12 kW up to 27 kW, increase the Column C demand by 5% per kW (or major fraction) above 12 kW.
Example: a single 15 kW range → base 8 kW + (15-12) × 5% = 8 kW × 1.15 = 9.2 kW .
Fixed Appliances (220.53)
A 75% demand factor may be applied to the total connected load of four or more fastened-in-place appliances rated ¼ hp or 500 W or more. This excludes dryers (220.54), ranges/cooking (220.55), space heating (220.51), and A/C (220.50). Typical qualifying appliances: dishwasher, disposal, water heater, trash compactor.
Neutral Reductions (220.61)
Per 220.61(B)(1) , the neutral for household ranges, ovens, counter-mounted cooking units, and dryers may be sized at 70% of the demand load from Tables 220.55 and 220.54. This is why a range feeder neutral is typically smaller than the ungrounded conductors.
Full Worked Example — 2000 sq ft Dwelling
A single-family dwelling, 120/240V, 2000 sq ft, with a 12 kW range, a 5 kW dryer, a dishwasher (1200 VA), disposal (900 VA), and water heater (4000 VA).
- Step 1 — General lighting load: 2000 sq ft × 3 VA = 6000 VA
- Step 2 — Add small-appliance + laundry circuits: 6000 + (2 × 1500) + 1500 = 10,500 VA
Step 3 — Apply Table 220.42:
- First 3000 VA × 100% = 3000 VA
- Remaining 7500 VA × 35% = 2625 VA
- Lighting demand = 5625 VA
- Step 4 — Range (Table 220.55, Column C): 12 kW range → 8 kW = 8000 VA
- Step 5 — Dryer (220.54): 5000 VA (minimum applies)
Step 6 — Fixed appliances (220.53): Dishwasher 1200 + disposal 900 + water heater 4000 = 6100 VA. Four or more fastened-in-place appliances? Only three listed here, so no 75% factor — use 6100 VA at 100%. (If a fourth qualifying appliance existed, apply 75%.)
Step 7 — Total service load: 5625 + 8000 + 5000 + 6100 = 24,725 VA
Step 8 — Convert to amps (240V): 24,725 ÷ 240 = 103 A → next standard size per 240.6(A) is 110 A , but a typical install would be a 100A or 125A service depending on engineering judgment. For exam answers, 24,725 VA ÷ 240 V ≈ 103 A.
Heating and Cooling Loads (220.50, 220.51)
Space heating loads are calculated per 220.51 at the connected load (100% of nameplate), with no demand factor. Air-conditioning and motor loads are calculated per 220.50 and 430.22 at 125% of the motor FLC for continuous-duty motors. The key rule for dwellings: when both heating and cooling are installed, use the larger of the two loads in the service calculation — they are considered noncoincident (you don't run the A/C and the electric furnace at the same time). This is the same principle that the 220.82 optional method formalizes in 220.82(C).
If a dwelling has a 10 kW electric furnace and a 5 kW A/C compressor, the service calculation uses 10 kW (the furnace), not 15 kW. Forgetting this noncoincident-load rule is one of the most expensive arithmetic mistakes on the exam.
Multifamily Standard Method
For a multifamily dwelling using the standard method, calculate each unit individually per Part III, sum the unit loads, then add house (common) loads (corridor lighting, parking lot lighting, common laundry) calculated per Part III. Demand factors of 220.42 apply per unit but not across units under the standard method — that cross-unit diversity is what the optional 220.84 method captures via Table 220.84.
Common Exam Traps
Forgetting to add small-appliance/laundry before applying 220.42.
Using 5000 VA for a dryer whose nameplate reads 5500 VA — use the larger nameplate.
Applying the 220.53 75% factor to only 3 appliances (need 4+).
Forgetting Note 1 on ranges over 12 kW (the 5% per kW bump).
Adding heating AND cooling instead of taking the larger noncoincident load.
Treating a 2000 sq ft dwelling's lighting at face value rather than applying the 35% demand tier.