Study guide

2.3 General Regulations: Materials, Protection, Support, Trenching & Structural Safety

Virginia Journeyman Plumber Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Overview, Virginia Licensing Law & Standards of Practice

1.1 Exam Format, Permitted References & Open-Book Strategy 1.2 Definitions, Licensure Requirement & Qualification for the Exam 1.3 Standards of Practice: Designations, Address Changes & License Use 1.4 Standards of Conduct, Prohibited Acts & Revocation of Licensure

2 Chapter 2: Renewal, USBC Administration & General Regulations

2.1 License Renewal, Continuing Education & Reinstatement 2.2 Virginia USBC Administration, Permits, Inspections & Required Tests 2.3 General Regulations: Materials, Protection, Support, Trenching & Structural Safety

3 Chapter 3: Plumbing Fixtures, Clearances & Temperature Control

3.1 Minimum Plumbing Facilities: Table 403.1, Calculations & Separate Facilities 3.2 Fixture Installation: Clearances, Compartments, Connections, Showers & Accessibility 3.3 Water Conservation, Temperature-Limiting Devices, Flushing Devices & Emergency Fixtures

4 Chapter 4: Fixture Traps, Trap Seals & Interceptors

4.1 Fixture Traps, Trap Seals & Trap Seal Protection 4.2 Grease Interceptors: Where Required, Sizing, Flow Control & Virginia's Disposer Rule 4.3 Oil Separators, Sand & Lint Interceptors, Other Interceptors & Corrosive Waste

5 Chapter 5: Sanitary Drainage Systems & Sizing

5.1 Drainage Principles & Drainage Fixture Units (Tables 709.1 and 709.2) 5.2 Horizontal Branches, Building Drains & Building Sewers: Slope, Sizing & Separation 5.3 Soil & Waste Stacks, Stack Offsets, Branch Connections & Relief Vents

6 Chapter 6: Drainage Fittings, Cleanouts, Indirect Waste & Sumps

6.1 Drainage Fittings, Changes of Direction, Joints & Prohibited Connections 6.2 Cleanouts: Locations, Spacing, Size, Clearance & Access 6.3 Indirect Waste, Air Gaps, Air Breaks, Waste Receptors & Condensate Disposal 6.4 Sumps, Sewage Pumps, Ejectors & Backwater Valves

7 Chapter 7: Vent Systems & Sizing

7.1 Vent Purpose, Terminals, Outdoor Extensions & Vent Connections 7.2 Trap-to-Vent Distance (Table 909.1) & Vent Pipe Sizing (906) 7.3 Common Vents, Wet Venting & Waste Stack Vents 7.4 Circuit Venting, Combination Waste & Vent, Island, Single-Stack & Air Admittance Valves

8 Chapter 8: Water Supply, Distribution Sizing, Hot Water & Water Heaters

8.1 Water Service, Pipe Materials, Joints, Valves, Pressure Control & Disinfection 8.2 Water Distribution Design: Flow and Pressure Criteria, Fixture Supplies & Pipe Sizing 8.3 Hot Water Supply: Delivery Distance, Temperature Control, Recirculation & Thermal Expansion 8.4 Water Heaters: Installation, Relief Valves, Discharge Piping & Drain Pans

9 Chapter 9: Backflow Prevention & Cross-Connection Control

9.1 Cross-Connections, Backsiphonage, Backpressure & Degree of Hazard 9.2 Air Gaps, Atmospheric Vacuum Breakers & Hose Connection Protection 9.3 Testable Assemblies: RP, Double Check, PVB & SVB; Location, Testing & Virginia Certification 9.4 Protecting Specific Connections: Beverage Dispensers, Boilers, Sprinklers, Irrigation & Equipment

10 Chapter 10: Storm Drainage Systems & Sizing (with Virginia Amendments)

10.1 Storm Drainage Basics: Disposal, Materials, Rainfall Rates & Roof Area 10.2 Sizing Leaders, Conductors, Horizontal Storm Drains & Gutters (Virginia Tables) 10.3 Secondary (Emergency) Roof Drains, Scuppers & Roof Ponding 10.4 Subsoil Drains, Building Subdrains, Storm Sumps, Controlled-Flow Roofs & Continuous Flow

2.3 General Regulations: Materials, Protection, Support, Trenching & Structural Safety

Key Takeaways Explain This Topic AI

Piping other than cast iron or galvanized steel that passes through framing less than 1-1/4 inches from the nearest edge must be protected by a steel shield plate at least 0.0575 inch thick (No. 16 gage) (IPC 305.6).

A pipe passing through a foundation wall needs a relieving arch, or a sleeve two pipe sizes larger than the pipe (IPC 305.3).

Exterior water supply piping must be at least 6 inches below the frost line and at least 12 inches below grade (IPC 305.4).

Table 308.5 hanger spacing examples: PVC and ABS 4 feet horizontal; cast iron 5 feet (10 feet with 10-foot lengths); copper tubing 1-1/4 inch and smaller 6 feet; PEX 1 inch and smaller 32 inches.

Where rock is found in a trench, remove it to at least 3 inches below the pipe and backfill with tamped sand (IPC 306.2.2); backfill in 6-inch layers until there are 12 inches of tamped earth over the crown (306.3).

Last updated: October 2026

What "General Regulations" covers

Outline area L (5 items) draws on IPC Chapter 3 together with the administrative rules covered in Section 2.2. Chapter 3 rules apply to every system, whether drainage, water or storm, so questions can combine them with other chapters.

Prohibited wastes and materials (IPC 302 and 303)

302.1: ashes, cinders or rags; flammable, poisonous or explosive liquids or gases; and oil, grease or other insoluble material that could obstruct, damage or overload the drainage or sewer system or interfere with sewage treatment must not be deposited into these systems.

302.2: industrial wastes may not enter the public sewer until the code official or other authority determines they will not damage the system or the treatment plant.

303.1: every length of pipe and every fitting, trap, fixture and device must bear the manufacturer's identification and the markings required by its standard.

303.2: materials are installed according to their standards or, if there are none, the manufacturer's instructions. When those instructions fall below the code's minimum, the code governs.

303.3 and 303.4: plastic pipe, fittings and components must be third-party certified to NSF 14 , and products required to meet a standard must be listed by a third-party certification agency .

303.5: cast-iron soil pipe, fittings and couplings must be third-party listed and labeled.

Rodentproofing (IPC 304)

Strainer plates on drain inlets: openings not greater than 1/2 inch in least dimension (304.2).

Meter boxes must keep rodents from entering by way of the water service pipe (304.3).

The annular space around pipes passing through walls, floors or ceilings must be sealed with caulking or closed with a compatible gasketing system (304.4).

Protection of pipes (IPC 305)

Section Rule

305.1 Contact Metallic piping, except cast iron, ductile iron and galvanized steel , must not be in direct contact with steel framing, concrete, cinder or masonry walls and floors, or corrosive soil. Plastic sheathing used to separate them must be at least 0.008 inch (8 mil) thick and must let the pipe move where it passes through concrete or masonry.

305.2 Stress and strain Install piping to prevent stresses that exceed the pipe's strength, and provide for expansion, contraction and structural settlement.

305.3 Foundation walls A pipe through a foundation wall needs a relieving arch , or a sleeve two pipe sizes larger than the pipe built into the wall.

305.4 Freezing Water, soil and waste pipes must not be installed outside a building, in attics or crawl spaces, in outside walls, or anywhere subject to freezing unless protected by insulation, heat or both. Exterior water supply piping must be at least 6 inches below the frost line and at least 12 inches below grade.

305.4.1 Sewer depth The 2021 IPC leaves the building sewer depth as a blank for the adopting jurisdiction. Virginia's amendments do not fill it in, so the local building official sets the requirement.

305.5 Waterproofing Roof joints around vent pipes must be made watertight with lead, copper, galvanized steel, aluminum, plastic or other approved flashing, and exterior wall openings must be watertight.

305.6 Physical damage In concealed locations, piping other than cast iron or galvanized steel passing through holes or notches in studs, joists, rafters or similar members less than 1-1/4 inches from the nearest edge must be protected by steel shield plates at least 0.0575 inch (No. 16 gage) thick. The plates cover the area of the pipe where the member is notched or bored and extend at least 2 inches above sole plates and below top plates .

305.7 Components Components installed along alleyways, driveways, parking garages or other locations exposed to damage must be recessed into the wall or otherwise protected in an approved manner.

Frost depth is a local design value. Use the frost line set by the local building department; Chapter 3 does not set a statewide number.

Joints between dissimilar metals are covered in Chapter 6, not Chapter 3. Under 605.23.1, copper tubing joins galvanized steel pipe through a copper-alloy fitting, dielectric fitting or ASSE 1079 dielectric union . Under 308.3, hangers must be made of material that will not promote galvanic action.

Trenching, excavation and backfill (IPC 306)

306.1: buried piping must be supported throughout its entire length.

306.2: where the trench bottom is the pipe bed, provide solid, continuous support between joints with bell holes, hub holes and coupling holes. Pipe must not be supported on blocks to grade. If the manufacturer's instructions are stricter, follow them.

306.2.1 Overexcavation: backfill to the pipe's installation level with sand or fine gravel in layers not greater than 6 inches , compacting each layer.

306.2.2 Rock removal: remove rock to not less than 3 inches below the bottom of the pipe and backfill with tamped sand . The pipe and joints must not rest on rock at any point.

306.2.3 Soft soil: overexcavate at least two pipe diameters and backfill with fine gravel, crushed stone or a concrete foundation bedded in tamped sand.

306.3 Backfilling: backfill must be free of debris. Place loose earth free of rocks, broken concrete and frozen chunks in 6-inch layers , tamped, until the pipe crown is covered by 12 inches of tamped earth . Bring the backfill up evenly on both sides.

307.5 Footings: trenches parallel to footings must not extend into the bearing plane, which is a line extending down at 45 degrees from the outside bottom edge of the footing or wall.

Structural safety (IPC 307) and framing limits

IPC 307.2 states that framing members shall not be cut, notched or bored beyond the limits in the International Building Code . 307.4 prohibits cutting or altering truss members without written approval from a registered design professional. The common conventional-framing limits from the IBC and IRC are:

Member Limit

Joist notch No more than 1/6 of the depth , no longer than 1/3 of the depth, and not in the middle third of the span ; end notches no more than 1/4 of the depth

Joist hole No more than 1/3 of the depth , and not within 2 inches of the top or bottom edge or of another hole or notch

Bearing stud Notch up to 25% of the width; hole up to 40% of the width, or 60% when the stud is doubled and no more than two successive doubled studs are bored; hole edge at least 5/8 inch from the stud edge

Non-bearing stud Notch up to 40% ; hole up to 60%

Top plate cut more than 50% of its width Galvanized metal tie at least 0.054 inch thick and 1-1/2 inches wide, fastened with eight 10d nails on each side and extending at least 6 inches past the opening

Pipe support (IPC 308)

Hangers and supports must carry the pipe and its contents, be attached to the structure in an approved way, and not promote galvanic action (308.3 and 308.4). Table 308.5 maximum spacing (horizontal / vertical, in feet):

  • Material Horizontal Vertical
  • ABS and PVC pipe 4 10
  • Cast-iron pipe 5 (10 where 10-foot lengths are installed) 15
  • Copper or copper-alloy pipe 12 10
  • Copper tubing 1-1/4 inch and smaller 6 10
  • Copper tubing 1-1/2 inch and larger 10 10
  • CPVC 1 inch and smaller / 1-1/4 inch and larger 3 / 4 10
  • PEX, PE-RT and PP 1 inch and smaller 2.67 (32 inches) 10
  • PEX, PE-RT and PP 1-1/4 inch and larger 4 10
  • Steel pipe 12 15
  • Lead pipe Continuous 4

For the materials marked with footnote b in the table (the plastics and stainless steel drainage systems), sizes 2 inches and smaller need a guide midway between the required vertical supports. Under 308.6 , horizontal drainage pipe 4 inches and larger that changes direction by more than 45 degrees needs rigid bracing against movement of the upstream pipe. Under 308.7.1 , pipe larger than 4 inches needs restraint at every change of direction and at changes in diameter greater than two pipe sizes. Under 308.10 , a thermal expansion tank must be supported according to the manufacturer's instructions and not by its connecting piping .

Other Chapter 3 items

309: in flood hazard areas, water service pipes, drainage piping, water heaters and vents follow IBC Section 1612.

310: washroom light and ventilation follow the IBC and IMC; fixture locations and compartments follow 405.3.

Section 311 (toilet facilities for workers) is deleted in Virginia.

315.1: the annular space around a pipe in a sleeve, or a pipe through the building envelope, must be sealed with caulking, foam sealant or gaskets compatible with the materials. Fire-rated penetrations follow the IBC.

316: alternative engineered designs require submittal and approval.

Loading diagram... Choosing protection for a pipe penetration