Study guide
2.1 License Renewal, Continuing Education & Reinstatement
Virginia Journeyman Plumber Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Overview, Virginia Licensing Law & Standards of Practice
1.1 Exam Format, Permitted References & Open-Book Strategy 1.2 Definitions, Licensure Requirement & Qualification for the Exam 1.3 Standards of Practice: Designations, Address Changes & License Use 1.4 Standards of Conduct, Prohibited Acts & Revocation of Licensure
2 Chapter 2: Renewal, USBC Administration & General Regulations
2.1 License Renewal, Continuing Education & Reinstatement 2.2 Virginia USBC Administration, Permits, Inspections & Required Tests 2.3 General Regulations: Materials, Protection, Support, Trenching & Structural Safety
3 Chapter 3: Plumbing Fixtures, Clearances & Temperature Control
3.1 Minimum Plumbing Facilities: Table 403.1, Calculations & Separate Facilities 3.2 Fixture Installation: Clearances, Compartments, Connections, Showers & Accessibility 3.3 Water Conservation, Temperature-Limiting Devices, Flushing Devices & Emergency Fixtures
4 Chapter 4: Fixture Traps, Trap Seals & Interceptors
4.1 Fixture Traps, Trap Seals & Trap Seal Protection 4.2 Grease Interceptors: Where Required, Sizing, Flow Control & Virginia's Disposer Rule 4.3 Oil Separators, Sand & Lint Interceptors, Other Interceptors & Corrosive Waste
5 Chapter 5: Sanitary Drainage Systems & Sizing
5.1 Drainage Principles & Drainage Fixture Units (Tables 709.1 and 709.2) 5.2 Horizontal Branches, Building Drains & Building Sewers: Slope, Sizing & Separation 5.3 Soil & Waste Stacks, Stack Offsets, Branch Connections & Relief Vents
6 Chapter 6: Drainage Fittings, Cleanouts, Indirect Waste & Sumps
6.1 Drainage Fittings, Changes of Direction, Joints & Prohibited Connections 6.2 Cleanouts: Locations, Spacing, Size, Clearance & Access 6.3 Indirect Waste, Air Gaps, Air Breaks, Waste Receptors & Condensate Disposal 6.4 Sumps, Sewage Pumps, Ejectors & Backwater Valves
7 Chapter 7: Vent Systems & Sizing
7.1 Vent Purpose, Terminals, Outdoor Extensions & Vent Connections 7.2 Trap-to-Vent Distance (Table 909.1) & Vent Pipe Sizing (906) 7.3 Common Vents, Wet Venting & Waste Stack Vents 7.4 Circuit Venting, Combination Waste & Vent, Island, Single-Stack & Air Admittance Valves
8 Chapter 8: Water Supply, Distribution Sizing, Hot Water & Water Heaters
8.1 Water Service, Pipe Materials, Joints, Valves, Pressure Control & Disinfection 8.2 Water Distribution Design: Flow and Pressure Criteria, Fixture Supplies & Pipe Sizing 8.3 Hot Water Supply: Delivery Distance, Temperature Control, Recirculation & Thermal Expansion 8.4 Water Heaters: Installation, Relief Valves, Discharge Piping & Drain Pans
9 Chapter 9: Backflow Prevention & Cross-Connection Control
9.1 Cross-Connections, Backsiphonage, Backpressure & Degree of Hazard 9.2 Air Gaps, Atmospheric Vacuum Breakers & Hose Connection Protection 9.3 Testable Assemblies: RP, Double Check, PVB & SVB; Location, Testing & Virginia Certification 9.4 Protecting Specific Connections: Beverage Dispensers, Boilers, Sprinklers, Irrigation & Equipment
10 Chapter 10: Storm Drainage Systems & Sizing (with Virginia Amendments)
10.1 Storm Drainage Basics: Disposal, Materials, Rainfall Rates & Roof Area 10.2 Sizing Leaders, Conductors, Horizontal Storm Drains & Gutters (Virginia Tables) 10.3 Secondary (Emergency) Roof Drains, Scuppers & Roof Ponding 10.4 Subsoil Drains, Building Subdrains, Storm Sumps, Controlled-Flow Roofs & Continuous Flow
2.1 License Renewal, Continuing Education & Reinstatement
Key Takeaways Explain This Topic AI
A Virginia plumber license expires three years from the last day of the month in which it was issued (18VAC50-30-120 A; § 54.1-1132).
Renewal and reinstatement require 3 hours of Board-approved continuing education per designation on building code changes, which for plumbing is the International Plumbing Code (18VAC50-30-120 C and -220 A).
If renewal requirements are not met within 30 days after expiration, a $210 reinstatement fee applies; it includes the $160 renewal fee (18VAC50-30-130 A-B).
A license may be reinstated for up to 24 months after expiration; after that, the person must apply as a new applicant but may sit for the same examination (18VAC50-30-130 D).
Work done after a license expires may be unlicensed activity, and a reinstated licensee is treated as continuously licensed for discipline purposes (18VAC50-30-130 E and -140 B).
Last updated: October 2026
The three-year cycle (18VAC50-30-120 A)
Licenses for electricians, gas fitters, liquefied petroleum gas fitters, natural gas fitter providers, HVAC tradesmen and plumbers expire three years from the last day of the month in which they were issued . § 54.1-1132 also states that a tradesman license is valid for three years. Other certifications under the chapter, such as the backflow prevention device worker certification, run on a two-year cycle (18VAC50-30-120 B).
Example: A license issued on October 12, 2026 expires on October 31, 2029 .
Continuing education (18VAC50-30-120 C, -210 to -230; § 54.1-1133)
Hours: licensees with plumbing, electrical or HVAC designations must complete three hours of continuing education for each designation as a condition of renewal or reinstatement. Gas fitter, LP gas fitter and natural gas fitter provider licensees need one hour.
Content: the course must relate to the applicable building code changes . § 54.1-1133 requires evidence of knowledge of code changes for renewal. Under 18VAC50-30-220 A, plumbing courses must cover articles of the current edition of the International Plumbing Code , including any changes. OSHA safety or business courses do not count toward this requirement.
Provider: the course must come from a Board-approved provider , and no credit is given until the Board approves the course (-220 C).
Reporting: providers send completion data to the Board electronically within seven days of finishing each course (-230). Providers keep class records for at least five years (-210 C).
A licensee with both plumbing and gas fitting designations needs three hours for plumbing and one hour for gas fitting.
Renewing on time (18VAC50-30-120 G to K)
The Board mails a renewal notice. Not receiving the notice does not relieve the licensee of the duty to renew. If the notice does not arrive, the licensee may send a copy of the license with the required fee as a renewal application within 30 days of the expiration date (-120 H).
The date DPOR or its agent receives the fee decides whether the licensee may renew or must reinstate (-120 I).
The Board may deny renewal for the same reasons it may refuse initial licensure or discipline a regulant. The regulant may request review under the Administrative Process Act (-120 J).
An unpaid monetary penalty, cost or fee under a consent or final order delays or withholds DPOR services, including renewal (-120 K).
Reinstatement (18VAC50-30-130 and -140)
- Situation Rule
- Requirements met within 30 days after expiration Renewal at the renewal fee
- Requirements not met within 30 days after expiration Reinstatement fee required (-130 A)
- Up to 24 months after expiration Reinstatement available (-130 D)
More than 24 months after expiration New application under current entry rules; eligible to sit for the same category of exam (-130 D)
Regulatory fees: renewal $160 for a tradesman license (-120 G); reinstatement $210, which includes the renewal fee (-130 B). You do not pay both. All fees are nonrefundable and are not prorated.
Technology fee: since July 1, 2026, DPOR adds a technology fee of $7.25 per year to certain fees under 2026's House Bill 30, through June 30, 2030. For example, the current exam-and-license application shows $171.75 for a $150 fee covering a 3-year license.
Continuing education: the three hours per designation also apply to reinstatement (-120 C).
Unlicensed activity: regulated activity after the license expires may be unlicensed activity and may be prosecuted under Chapter 1 or Chapter 11 of Title 54.1 (-130 E).
Expiration date after reinstatement: a reinstated licensee keeps the same license number and gets an expiration date three years from the previous expiration date for a tradesman license (-140 A).
Continuous licensure: a reinstated licensee is regarded as having been continuously licensed and stays under the Board's disciplinary authority for the whole period (-140 B).
Denial: the Board may deny reinstatement for the same reasons it may refuse licensure or discipline a regulant (-130 F).
Worked timeline
A journeyman plumbing license expires March 31, 2027:
By March 31, 2027: complete 3 CE hours, pay $160 plus the technology fee, and the license renews to March 31, 2030.
April 1 to April 30, 2027: renewal is still accepted, because the requirements are met within 30 days of expiration. Any work done while the license is expired is still at risk.
May 2027 through March 31, 2029: reinstatement only. Pay $210 plus the technology fee and complete CE. The new expiration date is March 31, 2030.
After March 31, 2029: reinstatement is no longer available. Apply as a new applicant under the entry requirements then in effect. The person is eligible to sit for the journeyman plumber exam again.
Penalties for working on an expired license
Practicing as a tradesman without a valid license is a Class 1 misdemeanor under § 54.1-1135 A and an unlawful act under § 54.1-111. A willful third conviction within 36 months is a Class 6 felony. The Board may also discipline a regulant for conduct during a lapse because of the continuous-licensure rule in -140 B.