Study guide
3.2 Fixture Installation: Clearances, Compartments, Connections, Showers & Accessibility
Virginia Journeyman Plumber Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Overview, Virginia Licensing Law & Standards of Practice
1.1 Exam Format, Permitted References & Open-Book Strategy 1.2 Definitions, Licensure Requirement & Qualification for the Exam 1.3 Standards of Practice: Designations, Address Changes & License Use 1.4 Standards of Conduct, Prohibited Acts & Revocation of Licensure
2 Chapter 2: Renewal, USBC Administration & General Regulations
2.1 License Renewal, Continuing Education & Reinstatement 2.2 Virginia USBC Administration, Permits, Inspections & Required Tests 2.3 General Regulations: Materials, Protection, Support, Trenching & Structural Safety
3 Chapter 3: Plumbing Fixtures, Clearances & Temperature Control
3.1 Minimum Plumbing Facilities: Table 403.1, Calculations & Separate Facilities 3.2 Fixture Installation: Clearances, Compartments, Connections, Showers & Accessibility 3.3 Water Conservation, Temperature-Limiting Devices, Flushing Devices & Emergency Fixtures
4 Chapter 4: Fixture Traps, Trap Seals & Interceptors
4.1 Fixture Traps, Trap Seals & Trap Seal Protection 4.2 Grease Interceptors: Where Required, Sizing, Flow Control & Virginia's Disposer Rule 4.3 Oil Separators, Sand & Lint Interceptors, Other Interceptors & Corrosive Waste
5 Chapter 5: Sanitary Drainage Systems & Sizing
5.1 Drainage Principles & Drainage Fixture Units (Tables 709.1 and 709.2) 5.2 Horizontal Branches, Building Drains & Building Sewers: Slope, Sizing & Separation 5.3 Soil & Waste Stacks, Stack Offsets, Branch Connections & Relief Vents
6 Chapter 6: Drainage Fittings, Cleanouts, Indirect Waste & Sumps
6.1 Drainage Fittings, Changes of Direction, Joints & Prohibited Connections 6.2 Cleanouts: Locations, Spacing, Size, Clearance & Access 6.3 Indirect Waste, Air Gaps, Air Breaks, Waste Receptors & Condensate Disposal 6.4 Sumps, Sewage Pumps, Ejectors & Backwater Valves
7 Chapter 7: Vent Systems & Sizing
7.1 Vent Purpose, Terminals, Outdoor Extensions & Vent Connections 7.2 Trap-to-Vent Distance (Table 909.1) & Vent Pipe Sizing (906) 7.3 Common Vents, Wet Venting & Waste Stack Vents 7.4 Circuit Venting, Combination Waste & Vent, Island, Single-Stack & Air Admittance Valves
8 Chapter 8: Water Supply, Distribution Sizing, Hot Water & Water Heaters
8.1 Water Service, Pipe Materials, Joints, Valves, Pressure Control & Disinfection 8.2 Water Distribution Design: Flow and Pressure Criteria, Fixture Supplies & Pipe Sizing 8.3 Hot Water Supply: Delivery Distance, Temperature Control, Recirculation & Thermal Expansion 8.4 Water Heaters: Installation, Relief Valves, Discharge Piping & Drain Pans
9 Chapter 9: Backflow Prevention & Cross-Connection Control
9.1 Cross-Connections, Backsiphonage, Backpressure & Degree of Hazard 9.2 Air Gaps, Atmospheric Vacuum Breakers & Hose Connection Protection 9.3 Testable Assemblies: RP, Double Check, PVB & SVB; Location, Testing & Virginia Certification 9.4 Protecting Specific Connections: Beverage Dispensers, Boilers, Sprinklers, Irrigation & Equipment
10 Chapter 10: Storm Drainage Systems & Sizing (with Virginia Amendments)
10.1 Storm Drainage Basics: Disposal, Materials, Rainfall Rates & Roof Area 10.2 Sizing Leaders, Conductors, Horizontal Storm Drains & Gutters (Virginia Tables) 10.3 Secondary (Emergency) Roof Drains, Scuppers & Roof Ponding 10.4 Subsoil Drains, Building Subdrains, Storm Sumps, Controlled-Flow Roofs & Continuous Flow
3.2 Fixture Installation: Clearances, Compartments, Connections, Showers & Accessibility
Key Takeaways Explain This Topic AI
A water closet, urinal, lavatory or bidet must be at least 15 inches from its center to a side wall or obstruction, at least 30 inches center to center from an adjacent fixture, and have at least 21 inches of clear space in front (IPC 405.3.1).
Water closet compartments must be at least 30 by 60 inches for floor-mounted and 30 by 56 inches for wall-hung water closets (IPC 405.3.1).
Virginia's 405.3.5 requires urinal partitions at least 30 inches apart that start no higher than 12 inches, rise to at least 60 inches, and extend 18 inches from the wall or 6 inches past the urinal lip, whichever is greater.
Shower compartments need at least 900 square inches of area and a 30-inch least dimension, or 25 inches with 1,300 square inches (IPC 421.4).
Water and drain pipes under accessible lavatories and sinks must be covered or configured to protect against contact (IPC 404.3).
Last updated: October 2026
Setting fixtures (IPC 405.1 to 405.3)
405.1: supply lines and fittings must prevent backflow.
405.2: fixtures must allow easy access for cleaning the fixture and the surrounding area.
405.3: fixtures must be set level and in proper alignment with adjacent walls.
Clearances (405.3.1)
Rule Dimension
Center of a water closet, urinal, lavatory or bidet to a side wall, partition, vanity or other obstruction at least 15 inches
Center to center between adjacent fixtures not separated by partitions at least 30 inches
Clear space in front of a water closet, urinal, lavatory or bidet to any wall, fixture or door at least 21 inches
- Compartment for a floor-mounted water closet at least 30 inches wide by 60 inches deep
- Compartment for a wall-hung water closet at least 30 inches wide by 56 inches deep
Accessible children's water closet (exception) at least 12 inches from center to the partition or wall on one side
The 15-inch side clearance on each side gives the familiar 30-inch minimum compartment width.
Other placement rules
405.3.2: in employee and public toilet rooms, the required lavatory must be in the same room as the required water closet. Virginia's exception allows educational occupancies to place it adjacent to the room, with no more than one operational door between the water closet and the lavatory.
405.3.3: piping, fixtures and equipment must not interfere with the normal operation of windows, doors or other egress openings.
Compartments and urinal partitions (Virginia 405.3.4 and 405.3.5)
Virginia rewrote both sections:
Water closet compartments (405.3.4): every water closet used by the public or employees must comply with 405.3.4.1 or 405.3.4.2, and all fully enclosed compartments must have occupancy indicators . In separate facilities, each water closet is in its own compartment with walls or partitions and a door. In multi-user gender-neutral facilities, the partitions and doors run from floor to ceiling, with gaps of no more than 1/2 inch at the floor and ceiling and no more than 1/8 inch between doors and partitions. Exceptions: a single-occupant room with a lockable door; child day care rooms with two or more water closets may leave one without a compartment; and I-3 housing areas.
Urinal partitions (405.3.5): each urinal used by the public or employees must be in a separate area with walls or partitions. The horizontal distance between walls or partitions at each urinal must be at least 30 inches . The partitions must begin no more than 12 inches above the floor and extend at least 60 inches above the floor . They must project from the wall at least 18 inches, or to at least 6 inches beyond the urinal's outermost front lip, whichever is greater . Exceptions: single-occupant or family/assisted-use rooms with a lockable door, and child day care rooms with two or more urinals, which may leave one without a partition. In multi-user gender-neutral rooms, urinals need floor-to-ceiling compartments or a separate room with a door (405.3.5.2).
Connections (IPC 405.4 to 405.10)
405.4: a floor-outlet fixture connects to the drain with a floor flange , or a waste connector and sealing gasket tested to ASME A112.4.3. The flange is attached to the drain and anchored to the structure . Wall-hung water closets connect with an approved extension nipple or horn adapter and are bolted to the hanger with corrosion-resistant bolts.
405.4.1 flange thickness: copper alloy at least 0.125 inch ; plastic at least 0.25 inch ; cast iron or galvanized malleable iron at least 0.25 inch with a 2-inch caulking depth. Hard-lead flanges must weigh at least 1 pound 9 ounces and contain at least 7.75% antimony. Closet screws and bolts must be copper alloy.
405.4.2: floor-outlet fixtures are secured with corrosion-resistant screws or bolts.
405.4.3: a wall-hung water closet bowl is supported by a concealed metal carrier attached to the structure, so that no strain reaches the fixture connector. The carrier must meet ASME A112.6.1M or A112.6.2.
425.4: a 4-by-3-inch closet bend is acceptable. Where a 3-inch bend is used, a 4-by-3-inch flange receives the fixture horn.
405.5: fixtures with pumped waste meet ASME A112.3.4/CSA B45.9.
405.6: joints where fixtures meet walls or floors must be sealed.
405.7: in mental health centers, pipes and traps must not be exposed and fixtures are bolted through walls.
405.8 and 405.8.1: standing water must not rise in an overflow when the stopper is closed. Overflows discharge on the inlet side of the trap . Exception: a flush tank overflow discharges into the fixture it serves.
405.9: slip joints need approved elastomeric gaskets and are allowed only on the trap inlet, the trap outlet and within the trap seal . A fixture with concealed slip joints needs an access panel or utility space at least 12 inches in its smallest dimension.
425.2 and 425.3: public and employee water closets need elongated bowls and hinged open-front seats .
Fixture outlet sizes
- Fixture Minimum waste outlet
- Lavatory (419.3) 1-1/4 inches, with a strainer, pop-up, crossbar or similar
- Bathtub (407.2) 1-1/2 inches; overflow, if provided, 1-1/2 inches
- Sink (422.2) 1-1/2 inches
Shower (421.3) 1-1/2 inches, with a removable strainer at least 3 inches in diameter and openings at least 1/4 inch
- Domestic food waste disposer (416.2) Connected to a drain at least 1-1/2 inches
- Showers (IPC 421)
421.2: the riser from the shower valve to the showerhead outlet must be attached to the structure.
421.4 compartment size: at least 900 square inches of interior cross-sectional area and at least 30 inches in least dimension , measured from the finished interior surfaces at the top of the threshold, and continued up to 70 inches above the drain. Exception: 25 inches in least dimension is allowed where the area is at least 1,300 square inches .
421.4.1: walls must be smooth, corrosion-resistant, nonabsorbent and waterproof to at least 6 feet above the floor and at least 70 inches above the drain.
421.4.2: the access opening must be at least 22 inches clear.
421.5.2 liners: turn up at least 2 inches above the finished threshold; no nails or holes less than 1 inch above the threshold; slope 1/4 inch per foot toward the drain. Liners are tested with water at least 2 inches deep at the threshold for 15 minutes (312.9).
421.6 and 407.3: glazing in shower and bathtub enclosures follows the IBC safety glazing rules.
Accessibility (IPC 404 and ICC A117.1)
Accessible fixtures are required by IBC Chapter 11 and installed to ICC A117.1 (404.1 and 404.2). The 2021 IBC references the 2017 edition of A117.1. IPC 404.3 requires water supply and drain pipes under accessible lavatories and sinks to be covered or otherwise configured to protect against contact , using covers that meet ASME A112.18.9 or ASTM C1822.
Common A117.1 dimensions for adult fixtures:
- Element Dimension
- Accessible water closet centerline from side wall 16 to 18 inches
- Seat height 17 to 19 inches above the floor
- Side-wall grab bar at least 42 inches long
- Rear-wall grab bar at least 36 inches long
- Grab bar height 33 to 36 inches to the top of the gripping surface
Wheelchair-accessible compartment at least 60 inches wide; at least 56 inches deep with a wall-hung closet, 59 inches with a floor-mounted closet
- Lavatory rim or counter no higher than 34 inches
- Knee clearance under lavatory at least 27 inches high
- Flush control on the open (transfer) side
Note the difference: the IPC's general rule is a minimum 15-inch centerline clearance, while the accessible water closet uses a 16-to-18-inch range from the side wall.
Other fixture connections
406.1 and 406.2: an automatic clothes washer's water supply is protected by an integral air gap or a backflow preventer. It drains through an air break into a standpipe (802.4.3) or into a laundry sink. The standpipe trap and fixture drain must be at least 2 inches and connect to a 3-inch or larger branch or stack.
409.4: a residential dishwasher drains to a wye on the sink tailpiece, to the disposer's dishwasher inlet, or through an air break to a standpipe. Its waste line must rise and be fastened to the underside of the sink rim or countertop .
426.5: a whirlpool tub pump needs access. Without manufacturer guidance, provide an opening of at least 12 by 12 inches , or 18 by 18 inches where the pump is more than 2 feet from the opening.