Study guide
4.6 Storage Tank Inspection, Meters, Services & Distribution Appurtenances
Virginia Water/Wastewater Operator Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Virginia Licensing, Regulations & Administrative Standards
1.1 Virginia DPOR Board Structure, License Categories & Scope of Practice 1.2 Experience, Education, Substitutions & Examination Approval 1.3 Renewal, Reinstatement, CPE Requirements & Discipline 1.4 Virginia Drinking Water & Wastewater Environmental Governance 1.5 Facility Classification & Minimum Operator Attendance 1.6 The ABC/WPI Exam Blueprint, References & Test-Day Rules 1.7 License Maintenance, Reporting Duties & Professional Conduct
2 Chapter 2: Source Water & Drinking Water Treatment Unit Processes
2.1 Source Water Hydrology, Groundwater Protection & Raw Water Quality 2.2 Coagulation, Flocculation & Sedimentation Processes 2.3 Filtration Technologies & Media Management 2.4 Disinfection Chemistry, CT Calculations & Disinfection Byproducts 2.5 Corrosion Control, Softening & Fluoridation Chemistry 2.6 Pretreatment: Screening, Presedimentation, Aeration & Preoxidation 2.7 Filter Backwash, Surface Wash, Air Scour & Filter Surveillance 2.8 Membrane Systems: MF, UF, NF and RO Operation & Integrity Testing 2.9 Water Treatment Residuals: Handling, Thickening & Disposal 2.10 Chemical Feed Systems: Metering Pumps, Dry Feeders & Calibration 2.11 Process Monitoring, Trend Interpretation & Plant Optimization 2.12 Iron and Manganese, Taste-and-Odor Control, GAC & PFAS
3 Chapter 3: Wastewater Treatment, Biological Processes & Biosolids
3.1 Preliminary Treatment & Primary Clarification 3.2 Activated Sludge Dynamics & Secondary Process Control 3.3 Attached Growth Systems & Advanced Biological Processes 3.4 Biological & Chemical Nutrient Removal (BNR/ENR) 3.5 Solids Thickening, Digestion & Biosolids Management 3.6 Wastewater Characteristics, Influent Loading & Industrial Pretreatment 3.7 Secondary Clarifier Operation & Sludge Blanket Control 3.8 Lagoons, Stabilization Ponds & Natural Treatment Systems 3.9 Tertiary Filtration, Effluent Polishing & Water Reuse 3.10 Wastewater Disinfection & Dechlorination Systems 3.11 Aeration Systems, Blowers, Diffusers & Dissolved Oxygen Control 3.12 Digester Gas Handling, Cogeneration & Gas System Safety 3.13 Biosolids Land Application, Part 503 & Virginia Permitting
4 Chapter 4: Distribution Networks, Collection Systems & Hydraulic Systems
4.1 Water Distribution Networks, Storage & Pressure Management 4.2 Cross-Connection Control & Backflow Prevention Assemblies 4.3 Wastewater Collection Systems, Lift Stations & Inflow/Infiltration 4.4 Centrifugal & Positive Displacement Pumps 4.5 Motors, Drives, Control Systems & SCADA 4.6 Storage Tank Inspection, Meters, Services & Distribution Appurtenances 4.7 Main Disinfection, Flushing & Distribution Water Quality Management 4.8 Sewer Cleaning, CCTV Inspection & Collection System Rehabilitation 4.9 Maintenance Programs, Asset Management & Pump Efficiency Testing 4.10 Odor Control, Standby Power & Ancillary Plant Equipment
5 Chapter 5: Laboratory Analysis, Environmental Safety & Applied Math
5.1 Water & Wastewater Laboratory Analysis & QA/QC Protocols 5.2 Confined Space Entry, Chemical Safety & OSHA/VOSH Compliance 5.3 Hydraulic, Dosage & Pounds Formula Math 5.4 Wastewater Process & Loading Rate Mathematics 5.5 Drinking Water Microbiology & the Revised Total Coliform Rule 5.6 Wastewater Laboratory Analysis: Nutrients, Metals, WET & Regulatory Testing 5.7 Instrument Calibration, Online Analyzers & Data Validation 5.8 Process Control Testing: Jar Tests, Settleometer & Microscopic Examination 5.9 Chemical Receiving, Storage, Spill Response & Hazardous Waste 5.10 Electrical Safety, Fall Protection, Excavation & Traffic Control 5.11 PPE, Respiratory Protection & Biological Hazards 5.12 Advanced Applied Math: Mass Balance, Blending & Efficiency
6 Chapter 6: Regulatory Compliance, Reporting & Plant Administration
6.1 Safe Drinking Water Act Compliance: MCLs, Monitoring & Violations 6.2 Public Notification, Consumer Confidence Reports & Customer Complaints 6.3 VPDES Permit Compliance, DMRs & Overflow Reporting 6.4 Operating Records, Logbooks, Reports & Data Integrity 6.5 Emergency Response Planning & AWIA Risk and Resilience 6.6 Facility Security, SCADA Cybersecurity & Vulnerability Assessment 6.7 Budgeting, Procurement, Inventory & Capital Planning 6.8 Supervision, Training, SOP Development & Resource Optimization
4.6 Storage Tank Inspection, Meters, Services & Distribution Appurtenances
Key Takeaways Explain This Topic AI
Finished water storage tanks should be inspected at least every three to five years, with the interior inspected by drained entry, diver, or remotely operated vehicle under a confined space and potable water protocol.
Air and vacuum release valves protect a main from column separation and from collapse during draining, and a plugged combination air valve is a common cause of unexplained pressure surges.
Altitude valves close automatically when a tank reaches full level, while pressure reducing valves hold a set downstream pressure independent of upstream pressure.
The Lead and Copper Rule Revisions required all community and non-transient non-community systems to complete a service line material inventory by October 16, 2024, classifying each line as lead, galvanized requiring replacement, non-lead, or unknown.
Displacement meters are accurate at low flow and are the standard residential meter, while turbine meters handle high flow but under-register at low flow, which is why compound meters combine both.
Last updated: August 2026
Storage Tank Inspection, Meters, Services & Distribution Appurtenances
The ABC Water Treatment outline lists "water storage tanks," "valves (e.g., backflow, control valve, isolating, throttling, pressure regulation)," and "maintain facility and process control water meters" among the equipment tasks an operator must inspect, maintain, and operate. This section covers the asset-management side of those items - what breaks, how it is inspected, and what the records must show.
- 1. Finished Water Storage Tanks
- Inspection program
Inspection Frequency Scope
Routine site check Monthly to quarterly Fencing, hatches locked, vents and overflow screened, no ponding, cathodic protection reading, no visible leakage
Exterior inspection Annually Coating condition, corrosion, structural connections, ladder and safety climb, roof and hatch seals, sample tap
Comprehensive interior inspection Every 3 to 5 years Sediment depth, coating condition and holidays, corrosion, structural welds and rivets, inlet/outlet condition, mixing pattern
Cleaning and disinfection As indicated by inspection, commonly 3 to 5 years Remove sediment, repair coating, disinfect per AWWA C652
Interior inspection methods, in order of cost and disruption:
Remotely operated vehicle (ROV) - a submersible camera. The tank stays in service, but coating adhesion cannot be assessed by camera.
Potable water diver - a diver in a fully encapsulating dry suit disinfected per protocol. The tank stays in service. Divers can measure sediment and probe coatings.
Drained entry - the only method that supports full coating assessment, dry-film thickness measurement, and welding repair. It is a permit-required confined space entry and takes the tank out of service.
Sanitary defects to look for
Vents must be screened (24 mesh) and turned down; a failed vent screen is a direct pathway for insects, birds, and rodents.
Overflow pipes must be screened and must discharge over an air gap , never be piped directly into a storm sewer or drain - that is a cross-connection.
Hatches must be locked, curbed, and gasketed, with the cover overlapping the curb downward.
Roof drainage must not pond over hatches or seams.
Sediment accumulation provides chlorine demand, harbors bacteria, and is the reason many tanks fail total coliform samples.
Coatings and cathodic protection
Interior coatings on potable tanks must be NSF/ANSI 61 certified . Modern systems are typically epoxy or polyurethane; older tanks may have lead-bearing or coal tar coatings, and removal is then a regulated lead or hazardous-material job with containment. Steel tanks in submerged service use impressed-current or sacrificial anode cathodic protection ; a routine operator task is reading and logging rectifier voltage and current.
Turnover and water quality
Storage exists for fire flow, equalization, and emergency supply - but volume that never moves becomes aged water. Practical controls include lowering the operating band to force turnover, installing active mixing systems , changing from a common inlet-outlet to separate inlet and outlet piping, and, for chloraminated systems, monitoring for nitrification with nitrite, total chlorine, and heterotrophic plate count.
2. Valves and Appurtenances
Device Function Operator issues
Gate valve Isolation, fully open or fully closed Exercise annually. A valve that has not been operated in a decade will not close when a main breaks. Record turns to close and compare to expected
Butterfly valve Isolation and throttling Slow closure required; fast closure causes water hammer
Check valve Prevents reverse flow Slamming on pump shutdown is a major surge source; use spring-assisted or slow-closing types
Pressure reducing valve (PRV) Holds a constant downstream pressure regardless of upstream pressure Pilot systems foul; a chattering PRV indicates it is sized too large for the flow
Pressure sustaining valve Holds a minimum upstream pressure Protects an upper zone from being drained by a lower zone
Altitude valve Closes automatically when a tank reaches its set full level Prevents overflow; a failed altitude valve is a common cause of tank overflow events
Air release valve Continuously vents accumulated air at high points under pressure Small orifice; plugs easily
Air/vacuum valve Large orifice; exhausts air during filling and admits air during draining Without it, draining a main can collapse it
- Combination air valve Both functions in one body The standard at high points
- Blow-off / flushing hydrant Dead-end flushing Must have an air gap; a submerged blow-off is a cross-connection
Why air valves matter more than they look. Trapped air at a high point reduces the effective pipe cross-section, increasing headloss; and a moving air pocket can cause a violent surge when it is suddenly expelled or compressed. A vacuum valve that fails to open during a rapid drawdown lets atmospheric pressure crush a large-diameter main, and it also allows backsiphonage of anything connected to the depressurized line.
Valve exercising programs should record valve number, location, direction, number of turns to close, condition, and whether it seated. Utilities target a full cycle of the system every one to three years, prioritizing critical isolation valves.
3. Service Lines and the Lead Inventory
- Material Era / notes
- Lead Pre-1950s in many areas; banned for potable use by the 1986 SDWA amendments
Galvanized iron/steel Corrodes internally; "galvanized requiring replacement" if it is or was downstream of a lead service line, because it adsorbs and later releases lead
- Copper with lead solder Lead solder banned in 1986; joints remain a lead source in older homes
- Copper, Type K Standard for new services
- Plastic - PE, PEX, CPVC Modern; must be NSF/ANSI 61 certified
The service line inventory. The Lead and Copper Rule Revisions required every community and non-transient non-community water system to prepare a service line material inventory by October 16, 2024 , classifying each service line - both the utility-owned and the customer-owned portion - as lead, galvanized requiring replacement, non-lead, or lead status unknown. The inventory must be made publicly accessible, updated, and used to drive replacement planning and customer notification. Unknowns must be investigated over time, and the LCRI accelerates replacement obligations beginning with the November 2027 compliance date.
Partial lead service line replacement - replacing only the utility side - is discouraged and in many cases prohibited, because disturbing the line and creating a galvanic couple between new copper and remaining lead can increase lead release for months.
- 4. Meters
- Types
Meter Principle Best range Notes
Positive displacement (nutating disc, oscillating piston) Fixed volume per cycle Low flow Standard residential meter; accurate at trickle flows; wears with sand
Single-jet / multi-jet Vanes driven by jets Low to moderate Common in small commercial
Turbine Rotor speed proportional to velocity High flow Under-registers at low flow ; used for irrigation and industrial
Compound Displacement chamber plus turbine with a changeover valve Full range For customers with both low overnight and high daytime flow
Electromagnetic Faraday's law; requires conductive fluid Full range, bidirectional No moving parts, no headloss; the standard for plant and master metering
Ultrasonic (transit-time) Time difference of sound with and against flow Full range No moving parts; clamp-on versions permit non-invasive checks
- Venturi / orifice / propeller Differential pressure or mechanical Moderate Older plant metering
- Accuracy and testing
AWWA standards set new-meter accuracy at approximately 98.5 to 101.5 percent in the normal flow range and 95 to 101 percent at the minimum test flow. Meters lose accuracy in one direction - they slow down and under-register - so an untested meter population is quietly giving water away.
Typical testing and replacement intervals: small residential meters every 10 years or by volume registered ; large meters (3 inch and above) annually ; and plant master meters annually , with calibration traceable and documented.
5. Water Loss and Non-Revenue Water
The AWWA water audit method replaces the old "unaccounted-for water" percentage with a structured balance:
System input volume (corrected for master meter error)
minus authorized consumption (billed metered, billed unmetered, unbilled metered, unbilled unmetered - for example, firefighting and main flushing)
equals water losses , split into:
Apparent losses - customer meter under-registration, data handling errors, and unauthorized consumption. These are revenue losses, valued at the retail rate.
Real losses - leakage on mains, services, and storage overflows. These are production cost losses, valued at the marginal cost of treatment.
Non-revenue water = billed authorized consumption subtracted from system input volume.
Why the distinction matters operationally. Apparent losses are fixed with a meter testing and replacement program and with billing system audits. Real losses are fixed with leak detection surveys - acoustic correlators, leak noise loggers, district metered areas with minimum-night-flow analysis - and with pressure management, since leakage rate rises with pressure. Chasing the wrong category wastes the budget.