Study guide

5.6 Wastewater Laboratory Analysis: Nutrients, Metals, WET & Regulatory Testing

Virginia Water/Wastewater Operator Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Virginia Licensing, Regulations & Administrative Standards

1.1 Virginia DPOR Board Structure, License Categories & Scope of Practice 1.2 Experience, Education, Substitutions & Examination Approval 1.3 Renewal, Reinstatement, CPE Requirements & Discipline 1.4 Virginia Drinking Water & Wastewater Environmental Governance 1.5 Facility Classification & Minimum Operator Attendance 1.6 The ABC/WPI Exam Blueprint, References & Test-Day Rules 1.7 License Maintenance, Reporting Duties & Professional Conduct

2 Chapter 2: Source Water & Drinking Water Treatment Unit Processes

2.1 Source Water Hydrology, Groundwater Protection & Raw Water Quality 2.2 Coagulation, Flocculation & Sedimentation Processes 2.3 Filtration Technologies & Media Management 2.4 Disinfection Chemistry, CT Calculations & Disinfection Byproducts 2.5 Corrosion Control, Softening & Fluoridation Chemistry 2.6 Pretreatment: Screening, Presedimentation, Aeration & Preoxidation 2.7 Filter Backwash, Surface Wash, Air Scour & Filter Surveillance 2.8 Membrane Systems: MF, UF, NF and RO Operation & Integrity Testing 2.9 Water Treatment Residuals: Handling, Thickening & Disposal 2.10 Chemical Feed Systems: Metering Pumps, Dry Feeders & Calibration 2.11 Process Monitoring, Trend Interpretation & Plant Optimization 2.12 Iron and Manganese, Taste-and-Odor Control, GAC & PFAS

3 Chapter 3: Wastewater Treatment, Biological Processes & Biosolids

3.1 Preliminary Treatment & Primary Clarification 3.2 Activated Sludge Dynamics & Secondary Process Control 3.3 Attached Growth Systems & Advanced Biological Processes 3.4 Biological & Chemical Nutrient Removal (BNR/ENR) 3.5 Solids Thickening, Digestion & Biosolids Management 3.6 Wastewater Characteristics, Influent Loading & Industrial Pretreatment 3.7 Secondary Clarifier Operation & Sludge Blanket Control 3.8 Lagoons, Stabilization Ponds & Natural Treatment Systems 3.9 Tertiary Filtration, Effluent Polishing & Water Reuse 3.10 Wastewater Disinfection & Dechlorination Systems 3.11 Aeration Systems, Blowers, Diffusers & Dissolved Oxygen Control 3.12 Digester Gas Handling, Cogeneration & Gas System Safety 3.13 Biosolids Land Application, Part 503 & Virginia Permitting

4 Chapter 4: Distribution Networks, Collection Systems & Hydraulic Systems

4.1 Water Distribution Networks, Storage & Pressure Management 4.2 Cross-Connection Control & Backflow Prevention Assemblies 4.3 Wastewater Collection Systems, Lift Stations & Inflow/Infiltration 4.4 Centrifugal & Positive Displacement Pumps 4.5 Motors, Drives, Control Systems & SCADA 4.6 Storage Tank Inspection, Meters, Services & Distribution Appurtenances 4.7 Main Disinfection, Flushing & Distribution Water Quality Management 4.8 Sewer Cleaning, CCTV Inspection & Collection System Rehabilitation 4.9 Maintenance Programs, Asset Management & Pump Efficiency Testing 4.10 Odor Control, Standby Power & Ancillary Plant Equipment

5 Chapter 5: Laboratory Analysis, Environmental Safety & Applied Math

5.1 Water & Wastewater Laboratory Analysis & QA/QC Protocols 5.2 Confined Space Entry, Chemical Safety & OSHA/VOSH Compliance 5.3 Hydraulic, Dosage & Pounds Formula Math 5.4 Wastewater Process & Loading Rate Mathematics 5.5 Drinking Water Microbiology & the Revised Total Coliform Rule 5.6 Wastewater Laboratory Analysis: Nutrients, Metals, WET & Regulatory Testing 5.7 Instrument Calibration, Online Analyzers & Data Validation 5.8 Process Control Testing: Jar Tests, Settleometer & Microscopic Examination 5.9 Chemical Receiving, Storage, Spill Response & Hazardous Waste 5.10 Electrical Safety, Fall Protection, Excavation & Traffic Control 5.11 PPE, Respiratory Protection & Biological Hazards 5.12 Advanced Applied Math: Mass Balance, Blending & Efficiency

6 Chapter 6: Regulatory Compliance, Reporting & Plant Administration

6.1 Safe Drinking Water Act Compliance: MCLs, Monitoring & Violations 6.2 Public Notification, Consumer Confidence Reports & Customer Complaints 6.3 VPDES Permit Compliance, DMRs & Overflow Reporting 6.4 Operating Records, Logbooks, Reports & Data Integrity 6.5 Emergency Response Planning & AWIA Risk and Resilience 6.6 Facility Security, SCADA Cybersecurity & Vulnerability Assessment 6.7 Budgeting, Procurement, Inventory & Capital Planning 6.8 Supervision, Training, SOP Development & Resource Optimization

5.6 Wastewater Laboratory Analysis: Nutrients, Metals, WET & Regulatory Testing

Key Takeaways Explain This Topic AI

Total nitrogen equals total Kjeldahl nitrogen plus nitrite nitrogen plus nitrate nitrogen, and total Kjeldahl nitrogen itself equals organic nitrogen plus ammonia nitrogen.

Total phosphorus requires a digestion step to convert condensed and organic phosphorus to orthophosphate, whereas orthophosphate is measured directly with no digestion.

Whole effluent toxicity testing exposes test organisms to graded effluent dilutions and reports acute results as an LC50 and chronic results as a no observed effect concentration or an IC25.

Regulatory compliance analyses must be performed by approved 40 CFR Part 136 methods in a laboratory accredited under the Virginia Environmental Laboratory Accreditation Program, while process control tests need not be.

The volatile acids to alkalinity ratio is the key anaerobic digester control test, with a healthy range of roughly 0.05 to 0.15 and souring indicated above about 0.3 to 0.4.

Last updated: August 2026

Wastewater Laboratory Analysis: Nutrients, Metals, WET & Regulatory Testing

The ABC Wastewater Class IV Laboratory Analysis area carries 15 items and, notably, zero calculation items - meaning these questions test procedure, interference, interpretation, and quality control rather than arithmetic. The outline names bacteriological, biological, chemical, physical, and advanced analytical methods, plus process control and required regulatory testing.

1. Nitrogen Series

The relationships are worth memorizing as equations, because permit forms and exam items both use them.

TKN = Organic nitrogen + Ammonia nitrogen Total nitrogen (TN) = TKN + Nitrite-N + Nitrate-N Organic nitrogen = TKN - Ammonia nitrogen

Analyte Common methods Notes

Ammonia (NH3-N) Ion-selective electrode; phenate colorimetric; salicylate; distillation followed by titration Distillation removes most interferences; preserve with sulfuric acid to pH below 2 and cool to 4 degrees C ; 28-day holding time

TKN Sulfuric acid/catalyst digestion converting organic N to ammonium, then ammonia determination The digestion is the whole test; incomplete digestion under-reports

Nitrite (NO2-N) Diazotization colorimetric 48-hour holding time, no acid preservation - acid converts nitrite; refrigerate only

Nitrate (NO3-N) Cadmium reduction to nitrite then colorimetric; UV spectrophotometric screening; ion chromatography Cadmium column efficiency must be verified; cadmium waste is hazardous

Total nitrogen Persulfate digestion, or calculation from TKN plus nitrite plus nitrate Chesapeake Bay permits are written on TN

A diagnostic worth knowing: if effluent ammonia is low, nitrate is high, and TKN is low, the plant is nitrifying but not denitrifying. If ammonia is low, nitrate is low, and TN is low, both are working. If ammonia is high and nitrate is near zero, nitrification has failed - check DO, sludge age, temperature, alkalinity, and for a toxic inhibitor.

  • 2. Phosphorus Series
  • Total phosphorus = Orthophosphate + Condensed (poly) phosphate + Organic phosphorus

Analyte Preparation Use

Orthophosphate (reactive P) Filtered, no digestion ; ascorbic acid or stannous chloride colorimetric Process control for chemical dosing - only ortho reacts with alum or ferric

Acid-hydrolyzable P Mild acid hydrolysis Converts condensed phosphates

Total phosphorus Persulfate or acid digestion of an unfiltered sample to convert everything to ortho, then the same colorimetric finish Permit compliance

The exam trap is straightforward: a total phosphorus result requires a digestion; an orthophosphate result does not. Reporting an undigested result as total phosphorus under-reports, sometimes badly, at plants with significant organic phosphorus.

3. Alkalinity, pH and Digester Control

Test Method Control range

Alkalinity Titration with standard sulfuric acid to a pH 4.5 endpoint (bromcresol green indicator), reported as mg/L as CaCO3 50 to 80 mg/L residual in a nitrifying aeration basin; 1,500 to 5,000 mg/L in an anaerobic digester

Volatile acids Titration between defined pH endpoints (typically the pH 5.1 to 3.5 distillation-free method), reported as acetic acid 50 to 500 mg/L in a healthy digester

Volatile acids to alkalinity ratio Calculated 0.05 to 0.15 healthy; above 0.3 to 0.4 indicates souring

pH Electrometric, calibrated with at least two buffers bracketing the sample Analyze immediately - the holding time is effectively zero

The VA/Alk ratio is the single most valuable digester test because it moves before pH does. Alkalinity buffers the accumulating acids, so pH stays near 7 until the buffer is nearly exhausted - by which time recovery is difficult. A ratio trending from 0.10 to 0.25 gives days of warning that pH alone would not.

4. Metals

Method Principle Typical use

Flame atomic absorption (FAA) Sample aspirated into a flame; a hollow cathode lamp measures absorption at an element-specific wavelength mg/L-level metals; one element at a time

Graphite furnace AA Electrothermal atomization Low microgram-per-liter levels

ICP-OES (atomic emission) Argon plasma excites atoms; emission measured Multi-element, moderate detection limits

ICP-MS Plasma plus mass spectrometry Multi-element, part-per-trillion detection; the modern standard for biosolids and trace metals

  • Cold vapor AA Mercury reduced to elemental vapor Mercury only
  • Hydride generation Volatile hydride formed Arsenic, selenium

Sample handling for metals: collect in acid-washed plastic or glass, preserve with nitric acid to pH below 2 , and hold up to 6 months (mercury 28 days). "Total" metals are digested before analysis; "dissolved" metals are filtered through 0.45 micron before preservation. Filtering after acidification redissolves particulate metal and invalidates the dissolved result.

Metals matter to an operator in three places: pretreatment program compliance, biosolids Part 503 limits, and effluent water-quality-based limits. A metals excursion in the biosolids and a metals excursion in the effluent generally point to the same industrial user.

5. Whole Effluent Toxicity

VPDES permits at many Virginia plants include whole effluent toxicity (WET) testing, which asks a question no chemical-specific limit can: does the whole effluent, with all its interactions, harm aquatic life?

Test type Duration Organisms Endpoint

Acute 24 to 96 hours Ceriodaphnia dubia , Pimephales promelas (fathead minnow), Daphnia LC50 - the concentration lethal to 50 percent of organisms; also reported as TUa = 100/LC50

Chronic 7 days Ceriodaphnia dubia (survival and reproduction), Pimephales promelas (survival and growth) NOEC (no observed effect concentration), IC25 ; TUc = 100/NOEC

Tests run a dilution series plus a control, with rigorous requirements for control survival, reference toxicant testing, and dilution water quality.

When a test fails, the permit generally requires a Toxicity Reduction Evaluation (TRE) , often beginning with a Toxicity Identification Evaluation (TIE) that manipulates the sample - filtration, aeration, pH adjustment, EDTA chelation, C18 solid-phase extraction, sodium thiosulfate addition - to identify the class of toxicant. Common culprits at municipal plants: residual chlorine (identified by the thiosulfate manipulation), ammonia (pH manipulation), surfactants , and metals (EDTA manipulation).

6. Process Control Versus Regulatory Testing

This distinction determines what method, what laboratory, and what documentation is required.

  • Process control testing Regulatory compliance testing
  • Purpose Operating decisions Permit reporting

Method Any method the operator trusts - settleometer, centrifuge spins, quick COD, field DO Must be an approved method under 40 CFR Part 136

  • Laboratory The plant bench Must be accredited
  • Documentation Operator log Full chain of custody, QC data, and reporting
  • Consequence of error A bad process decision A permit violation or a false report

Virginia accreditation. Laboratories performing analyses for compliance with Virginia environmental programs must be accredited under the Virginia Environmental Laboratory Accreditation Program (VELAP) , administered by the Department of General Services Division of Consolidated Laboratory Services under 1VAC30-46 , based on the TNI standard. VELAP accreditation is field-of-testing specific: a plant lab may be accredited for BOD, TSS, pH, and residual chlorine while sending metals, nutrients, and WET to a contract laboratory.

A caution about the boundary. A plant may run any test it likes for process control, but the moment a result is used on a DMR it becomes a compliance result and must meet every Part 136 and accreditation requirement. Reporting a process-control number on a DMR is a data integrity problem, not a technicality - and under 18VAC160-30-320 it exposes the licensee personally.