Study guide

3.13 Biosolids Land Application, Part 503 & Virginia Permitting

Virginia Water/Wastewater Operator Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Virginia Licensing, Regulations & Administrative Standards

1.1 Virginia DPOR Board Structure, License Categories & Scope of Practice 1.2 Experience, Education, Substitutions & Examination Approval 1.3 Renewal, Reinstatement, CPE Requirements & Discipline 1.4 Virginia Drinking Water & Wastewater Environmental Governance 1.5 Facility Classification & Minimum Operator Attendance 1.6 The ABC/WPI Exam Blueprint, References & Test-Day Rules 1.7 License Maintenance, Reporting Duties & Professional Conduct

2 Chapter 2: Source Water & Drinking Water Treatment Unit Processes

2.1 Source Water Hydrology, Groundwater Protection & Raw Water Quality 2.2 Coagulation, Flocculation & Sedimentation Processes 2.3 Filtration Technologies & Media Management 2.4 Disinfection Chemistry, CT Calculations & Disinfection Byproducts 2.5 Corrosion Control, Softening & Fluoridation Chemistry 2.6 Pretreatment: Screening, Presedimentation, Aeration & Preoxidation 2.7 Filter Backwash, Surface Wash, Air Scour & Filter Surveillance 2.8 Membrane Systems: MF, UF, NF and RO Operation & Integrity Testing 2.9 Water Treatment Residuals: Handling, Thickening & Disposal 2.10 Chemical Feed Systems: Metering Pumps, Dry Feeders & Calibration 2.11 Process Monitoring, Trend Interpretation & Plant Optimization 2.12 Iron and Manganese, Taste-and-Odor Control, GAC & PFAS

3 Chapter 3: Wastewater Treatment, Biological Processes & Biosolids

3.1 Preliminary Treatment & Primary Clarification 3.2 Activated Sludge Dynamics & Secondary Process Control 3.3 Attached Growth Systems & Advanced Biological Processes 3.4 Biological & Chemical Nutrient Removal (BNR/ENR) 3.5 Solids Thickening, Digestion & Biosolids Management 3.6 Wastewater Characteristics, Influent Loading & Industrial Pretreatment 3.7 Secondary Clarifier Operation & Sludge Blanket Control 3.8 Lagoons, Stabilization Ponds & Natural Treatment Systems 3.9 Tertiary Filtration, Effluent Polishing & Water Reuse 3.10 Wastewater Disinfection & Dechlorination Systems 3.11 Aeration Systems, Blowers, Diffusers & Dissolved Oxygen Control 3.12 Digester Gas Handling, Cogeneration & Gas System Safety 3.13 Biosolids Land Application, Part 503 & Virginia Permitting

4 Chapter 4: Distribution Networks, Collection Systems & Hydraulic Systems

4.1 Water Distribution Networks, Storage & Pressure Management 4.2 Cross-Connection Control & Backflow Prevention Assemblies 4.3 Wastewater Collection Systems, Lift Stations & Inflow/Infiltration 4.4 Centrifugal & Positive Displacement Pumps 4.5 Motors, Drives, Control Systems & SCADA 4.6 Storage Tank Inspection, Meters, Services & Distribution Appurtenances 4.7 Main Disinfection, Flushing & Distribution Water Quality Management 4.8 Sewer Cleaning, CCTV Inspection & Collection System Rehabilitation 4.9 Maintenance Programs, Asset Management & Pump Efficiency Testing 4.10 Odor Control, Standby Power & Ancillary Plant Equipment

5 Chapter 5: Laboratory Analysis, Environmental Safety & Applied Math

5.1 Water & Wastewater Laboratory Analysis & QA/QC Protocols 5.2 Confined Space Entry, Chemical Safety & OSHA/VOSH Compliance 5.3 Hydraulic, Dosage & Pounds Formula Math 5.4 Wastewater Process & Loading Rate Mathematics 5.5 Drinking Water Microbiology & the Revised Total Coliform Rule 5.6 Wastewater Laboratory Analysis: Nutrients, Metals, WET & Regulatory Testing 5.7 Instrument Calibration, Online Analyzers & Data Validation 5.8 Process Control Testing: Jar Tests, Settleometer & Microscopic Examination 5.9 Chemical Receiving, Storage, Spill Response & Hazardous Waste 5.10 Electrical Safety, Fall Protection, Excavation & Traffic Control 5.11 PPE, Respiratory Protection & Biological Hazards 5.12 Advanced Applied Math: Mass Balance, Blending & Efficiency

6 Chapter 6: Regulatory Compliance, Reporting & Plant Administration

6.1 Safe Drinking Water Act Compliance: MCLs, Monitoring & Violations 6.2 Public Notification, Consumer Confidence Reports & Customer Complaints 6.3 VPDES Permit Compliance, DMRs & Overflow Reporting 6.4 Operating Records, Logbooks, Reports & Data Integrity 6.5 Emergency Response Planning & AWIA Risk and Resilience 6.6 Facility Security, SCADA Cybersecurity & Vulnerability Assessment 6.7 Budgeting, Procurement, Inventory & Capital Planning 6.8 Supervision, Training, SOP Development & Resource Optimization

3.13 Biosolids Land Application, Part 503 & Virginia Permitting

Key Takeaways Explain This Topic AI

Land application under 40 CFR Part 503 requires meeting three independent requirements at once: pollutant limits, a pathogen reduction class, and a vector attraction reduction option.

Class A biosolids meet a fecal coliform density below 1,000 most probable number per gram of total solids dry weight or a Salmonella density below 3 most probable number per 4 grams and may be distributed without site restrictions.

Class B biosolids meet a geometric mean fecal coliform density below 2 million most probable number per gram and carry crop harvesting, grazing, and public access restrictions.

The agronomic rate is set by the plant available nitrogen requirement of the crop, so nitrogen normally controls the application rate even when metals are far below their limits.

Virginia regulates biosolids land application through DEQ under the Virginia Pollution Abatement permit regulation 9VAC25-32, which adds nutrient management plans, setbacks, notification, and local monitoring on top of the federal Part 503 requirements.

Last updated: August 2026

Biosolids Land Application, Part 503 & Virginia Permitting

The ABC Wastewater outline lists "solids disposal: land application, landfill" as a treatment process task and places regulatory compliance and reporting in the Security, Safety, and Administrative Procedures area. In Virginia, biosolids land application is also politically visible, which means the operator's records will be read by people other than regulators.

1. The Three Independent Part 503 Requirements

Biosolids applied to land must simultaneously satisfy all three of the following. Failing any one disqualifies the material.

  • Pollutant limits (metals concentrations and loadings)
  • Pathogen reduction (Class A or Class B)
  • Vector attraction reduction (one of 10 listed options)

They are not alternatives, and a candidate who treats them as a single test will miss the question.

2. Pollutant Limits (40 CFR 503.13)

Part 503 regulates nine metals with four different limit tables.

Pollutant Ceiling concentration (mg/kg dry) Pollutant concentration ("high quality," mg/kg dry) Cumulative loading (kg/ha) Annual loading (kg/ha/yr)

  • Arsenic 75 41 41 2.0
  • Cadmium 85 39 39 1.9
  • Copper 4,300 1,500 1,500 75
  • Lead 840 300 300 15
  • Mercury 57 17 17 0.85
  • Molybdenum 75 - - -
  • Nickel 420 420 420 21
  • Selenium 100 100 100 5.0
  • Zinc 7,500 2,800 2,800 140

How the tables interact:

Ceiling concentration limits are absolute. Exceed any one and the material cannot be land applied at all , regardless of anything else.

If a batch meets the pollutant concentration (Table 3) limits, it is "exceptional quality" with respect to metals , and cumulative loading tracking is not required.

If it meets ceilings but not Table 3, it may still be applied, but the applier must track cumulative loading on each site against the Table 2 limits and observe the Table 4 annual limits.

"Exceptional quality" (EQ) biosolids meet the Table 3 pollutant concentrations and Class A pathogen reduction and one of the vector attraction options 1 through 8. EQ material can be bagged and sold to the public with essentially no general requirements or site restrictions.

  • 3. Pathogen Reduction
  • Class A

Fecal coliform below 1,000 MPN per gram of total solids (dry weight) , or Salmonella below 3 MPN per 4 grams of total solids , measured at the time of use or disposal.

Plus one of six alternatives (time-and-temperature, alkaline treatment with pH and temperature and drying conditions, prior/no prior testing for enteric virus and helminth ova, a Process to Further Reduce Pathogens (PFRP) , or an equivalent process approved by the permitting authority).

Listed PFRPs: composting, heat drying, heat treatment, thermophilic aerobic digestion, beta ray irradiation, gamma ray irradiation, and pasteurization.

Class A material carries no site restrictions .

Class B

Meet one of three alternatives: (1) a geometric mean of seven samples below 2,000,000 MPN or CFU fecal coliform per gram of total solids dry weight ; (2) use of a Process to Significantly Reduce Pathogens (PSRP) ; or (3) an equivalent process.

Listed PSRPs: aerobic digestion, anaerobic digestion, air drying, composting, and lime stabilization.

Class B material must be applied with site restrictions (below).

Class B site restrictions (40 CFR 503.32(b)(5))

  • Activity Waiting period after application
  • Harvest food crops with harvested parts touching the biosolids/soil mixture and grown in the surface 14 months

Harvest food crops with harvested parts below the surface where biosolids remain on the surface 4 months or longer before incorporation 20 months

  • Same, where biosolids remain on the surface less than 4 months before incorporation 38 months
  • Harvest food crops, feed crops, and fiber crops (parts not touching the surface) 30 days
  • Animal grazing 30 days
  • Harvest turf placed on lawns or high public-exposure sites 1 year
  • Public access, high potential for exposure 1 year
  • Public access, low potential for exposure 30 days
  • 4. Vector Attraction Reduction (40 CFR 503.33)

Ten options; the ones an operator is most likely to be using:

38 percent volatile solids reduction across the treatment process.

Anaerobic bench test - additional anaerobic digestion of a sample for 40 days at 30 to 37 degrees C yields less than 17 percent additional VS reduction.

Aerobic bench test - additional aerobic digestion for 30 days at 20 degrees C yields less than 15 percent additional VS reduction.

Specific oxygen uptake rate (SOUR) at or below 1.5 mg O2 per gram of total solids per hour at 20 degrees C (aerobically digested only).

Aerobic treatment 14 days or longer at above 40 degrees C with an average above 45 degrees C (composting).

Alkali addition to pH 12 for 2 hours and pH 11.5 for an additional 22 hours without adding more alkali.

Drying to at least 75 percent solids with no unstabilized solids.

Drying to at least 90 percent solids where unstabilized solids are present.

Injection below the surface with no significant amount on the surface within one hour.

Incorporation into the soil within 8 hours of application. For Class A material, the sludge must additionally be applied to the land within 8 hours after being discharged from the pathogen reduction process .

Note that options 9 and 10 are management practices at the field , not treatment at the plant, and they are the two most commonly relied upon by Class B land application programs.

5. Agronomic Rate - Nitrogen Usually Controls

The agronomic rate is the biosolids application rate that supplies the plant available nitrogen (PAN) the crop needs and no more, so that nitrogen does not leach to groundwater.

Application rate (dry tons/acre) = Crop N requirement (lb/acre) / PAN (lb N per dry ton)

PAN is computed from the biosolids analysis:

PAN = (Kmin x Organic N) + (Kvol x NH4-N) + NO3-N

Kmin is the first-year mineralization rate of organic nitrogen - typically 0.20 for anaerobically digested , 0.30 for aerobically digested, 0.10 for composted.

Kvol accounts for ammonia volatilization loss - typically 0.5 for surface application , 1.0 for injected or immediately incorporated material.

Worked example

Biosolids contain 38,000 mg/kg organic N, 6,000 mg/kg ammonium N, and negligible nitrate. They are anaerobically digested (Kmin 0.20) and surface applied (Kvol 0.5). The crop needs 130 lb N per acre.

Convert mg/kg to lb per dry ton: multiply by 0.002. Organic N = 38,000 x 0.002 = 76 lb/dry ton . Ammonium N = 6,000 x 0.002 = 12 lb/dry ton .

  • PAN = (0.20 x 76) + (0.5 x 12) = 15.2 + 6.0 = 21.2 lb PAN per dry ton
  • Rate = 130 / 21.2 = 6.1 dry tons per acre

Why nitrogen controls. At 6.1 dry tons per acre, the cumulative metals loading is a small fraction of the Part 503 limits - typically a few percent per application. A site would need decades of repeated application to approach a cumulative metals limit, whereas nitrogen constrains every single event. That is why "agronomic rate" and "nitrogen-based rate" are treated as synonyms in practice, except where a state imposes a phosphorus-based rate on high-phosphorus soils.

6. Virginia's Additional Requirements

Federal Part 503 sets the floor. Virginia adds requirements through DEQ under the Virginia Pollution Abatement (VPA) permit regulation, 9VAC25-32 , which contains the state's biosolids use standards.

Practical obligations layered on top of Part 503:

Permits. Land application requires a VPA permit or coverage under the general permit for biosolids management, held by the generator or the land applier. Individual field sites are approved and mapped.

Nutrient management plan. Prepared by a certified nutrient management planner for each site, setting the application rate on nitrogen and, on high-phosphorus soils, on phosphorus.

Setbacks and buffers from occupied dwellings, property lines, wells, surface waters, and roads, with distances that vary by application method - injected material gets smaller setbacks than surface-applied.

Notification. Advance notice to the local governing body and, in many cases, posted signage before application begins. This is a Virginia-specific requirement that has real enforcement consequences.

Local monitoring. Virginia localities may adopt an ordinance to monitor land application and may charge a fee; local monitors have authority to observe operations and report violations to DEQ.

Certified land applier requirements and operator record retention.

Recordkeeping and annual reporting covering quantities, sites, analytical results, pathogen and vector attraction certifications, and cumulative loading where applicable.

What the operator actually does. Sample and analyze each batch for the nine metals, nutrients, percent solids, and pathogen indicator; verify and document the vector attraction option used; certify pathogen class; give the hauler and applier the analysis; and retain records - Part 503 requires five years for most records and indefinitely for cumulative loading records at sites receiving non-EQ material.