Study guide
2.10 Chemical Feed Systems: Metering Pumps, Dry Feeders & Calibration
Virginia Water/Wastewater Operator Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Virginia Licensing, Regulations & Administrative Standards
1.1 Virginia DPOR Board Structure, License Categories & Scope of Practice 1.2 Experience, Education, Substitutions & Examination Approval 1.3 Renewal, Reinstatement, CPE Requirements & Discipline 1.4 Virginia Drinking Water & Wastewater Environmental Governance 1.5 Facility Classification & Minimum Operator Attendance 1.6 The ABC/WPI Exam Blueprint, References & Test-Day Rules 1.7 License Maintenance, Reporting Duties & Professional Conduct
2 Chapter 2: Source Water & Drinking Water Treatment Unit Processes
2.1 Source Water Hydrology, Groundwater Protection & Raw Water Quality 2.2 Coagulation, Flocculation & Sedimentation Processes 2.3 Filtration Technologies & Media Management 2.4 Disinfection Chemistry, CT Calculations & Disinfection Byproducts 2.5 Corrosion Control, Softening & Fluoridation Chemistry 2.6 Pretreatment: Screening, Presedimentation, Aeration & Preoxidation 2.7 Filter Backwash, Surface Wash, Air Scour & Filter Surveillance 2.8 Membrane Systems: MF, UF, NF and RO Operation & Integrity Testing 2.9 Water Treatment Residuals: Handling, Thickening & Disposal 2.10 Chemical Feed Systems: Metering Pumps, Dry Feeders & Calibration 2.11 Process Monitoring, Trend Interpretation & Plant Optimization 2.12 Iron and Manganese, Taste-and-Odor Control, GAC & PFAS
3 Chapter 3: Wastewater Treatment, Biological Processes & Biosolids
3.1 Preliminary Treatment & Primary Clarification 3.2 Activated Sludge Dynamics & Secondary Process Control 3.3 Attached Growth Systems & Advanced Biological Processes 3.4 Biological & Chemical Nutrient Removal (BNR/ENR) 3.5 Solids Thickening, Digestion & Biosolids Management 3.6 Wastewater Characteristics, Influent Loading & Industrial Pretreatment 3.7 Secondary Clarifier Operation & Sludge Blanket Control 3.8 Lagoons, Stabilization Ponds & Natural Treatment Systems 3.9 Tertiary Filtration, Effluent Polishing & Water Reuse 3.10 Wastewater Disinfection & Dechlorination Systems 3.11 Aeration Systems, Blowers, Diffusers & Dissolved Oxygen Control 3.12 Digester Gas Handling, Cogeneration & Gas System Safety 3.13 Biosolids Land Application, Part 503 & Virginia Permitting
4 Chapter 4: Distribution Networks, Collection Systems & Hydraulic Systems
4.1 Water Distribution Networks, Storage & Pressure Management 4.2 Cross-Connection Control & Backflow Prevention Assemblies 4.3 Wastewater Collection Systems, Lift Stations & Inflow/Infiltration 4.4 Centrifugal & Positive Displacement Pumps 4.5 Motors, Drives, Control Systems & SCADA 4.6 Storage Tank Inspection, Meters, Services & Distribution Appurtenances 4.7 Main Disinfection, Flushing & Distribution Water Quality Management 4.8 Sewer Cleaning, CCTV Inspection & Collection System Rehabilitation 4.9 Maintenance Programs, Asset Management & Pump Efficiency Testing 4.10 Odor Control, Standby Power & Ancillary Plant Equipment
5 Chapter 5: Laboratory Analysis, Environmental Safety & Applied Math
5.1 Water & Wastewater Laboratory Analysis & QA/QC Protocols 5.2 Confined Space Entry, Chemical Safety & OSHA/VOSH Compliance 5.3 Hydraulic, Dosage & Pounds Formula Math 5.4 Wastewater Process & Loading Rate Mathematics 5.5 Drinking Water Microbiology & the Revised Total Coliform Rule 5.6 Wastewater Laboratory Analysis: Nutrients, Metals, WET & Regulatory Testing 5.7 Instrument Calibration, Online Analyzers & Data Validation 5.8 Process Control Testing: Jar Tests, Settleometer & Microscopic Examination 5.9 Chemical Receiving, Storage, Spill Response & Hazardous Waste 5.10 Electrical Safety, Fall Protection, Excavation & Traffic Control 5.11 PPE, Respiratory Protection & Biological Hazards 5.12 Advanced Applied Math: Mass Balance, Blending & Efficiency
6 Chapter 6: Regulatory Compliance, Reporting & Plant Administration
6.1 Safe Drinking Water Act Compliance: MCLs, Monitoring & Violations 6.2 Public Notification, Consumer Confidence Reports & Customer Complaints 6.3 VPDES Permit Compliance, DMRs & Overflow Reporting 6.4 Operating Records, Logbooks, Reports & Data Integrity 6.5 Emergency Response Planning & AWIA Risk and Resilience 6.6 Facility Security, SCADA Cybersecurity & Vulnerability Assessment 6.7 Budgeting, Procurement, Inventory & Capital Planning 6.8 Supervision, Training, SOP Development & Resource Optimization
2.10 Chemical Feed Systems: Metering Pumps, Dry Feeders & Calibration
Key Takeaways Explain This Topic AI
Drawdown calibration measures the actual volume a metering pump delivers over a timed interval from a calibration cylinder and is the only reliable proof of feed rate.
Flow-paced control multiplies chemical output by plant flow to hold a constant dosage, while compound loop control trims the flow-paced signal using a measured residual.
Fluoride and other high-hazard feed pumps must be electrically interlocked with the flow meter or well pump and fitted with anti-siphon devices so chemical cannot be fed when water is not flowing.
Gas chlorinators operate under vacuum so that any breach in the line downstream of the vacuum regulator draws air in rather than releasing chlorine gas.
Sodium hypochlorite decomposes with time, heat, light, and trace metals, losing roughly half its available chlorine strength in three to six months at warm storage temperatures.
Last updated: August 2026
Chemical Feed Systems: Metering Pumps, Dry Feeders & Calibration
The ABC Water Treatment outline lists "chemical feed pumps," "chemical feed equipment," "mix batches of chemical solutions," "add chemicals to hoppers and feed equipment," and "calibrate inline instrumentation" as separate job tasks. Getting the chemistry right in a jar test is worthless if the feeder does not deliver what the operator thinks it is delivering.
- 1. Liquid Chemical Feeders
- Diaphragm metering pumps
The workhorse of water treatment. A reciprocating diaphragm displaces a fixed volume per stroke through ball or poppet check valves.
Output = stroke length x stroke frequency. Both are adjustable, but turndown is much better on frequency than on stroke length. Below roughly 20 to 25 percent stroke length, accuracy collapses because the check valves do not seat consistently. When a low dose is needed, reduce speed and keep stroke length near 100 percent, or dilute the chemical.
Priming problems are the most common failure. Off-gassing chemicals - sodium hypochlorite in warm weather is the classic - form a gas bubble under the discharge check that the diaphragm simply compresses and re-expands each stroke. The pump runs, sounds normal, and delivers nothing. Cures: degassing valve heads, flooded suction, a foot valve, and pumping from the bottom of the day tank.
Back pressure valve is required when discharging into a low-pressure or open point, otherwise the pump siphons.
Pulsation dampener smooths the sawtooth output when a steady rate matters (for example, ahead of an in-line static mixer).
Peristaltic (hose) pumps
A roller squeezes a flexible tube. The chemical touches only the tube, so there are no check valves to foul - ideal for slurries, polymers, and lime. Output is directly proportional to speed. The tube is a wear item with a predictable life; output declines gradually as the tube takes a set , which is why peristaltic pumps must be recalibrated on a schedule rather than only after a failure.
Progressive cavity and gear pumps
Used for viscous chemicals such as neat polymer or high-concentration ferric. Both are positive displacement, so both require a discharge pressure relief valve - a positive displacement pump against a closed valve will burst the pipe.
2. Dry Chemical Feeders
Type Principle Accuracy Use
Volumetric Delivers a fixed volume per revolution - screw, belt, rotary vane, or oscillating hopper Plus or minus 2 to 5 percent Small plants, consistent free-flowing chemical
Gravimetric Delivers a fixed weight per unit time, using a loss-in-weight hopper or a belt on load cells Plus or minus 0.5 to 1 percent Large plants, expensive chemicals, lime
Volumetric feeders are vulnerable to bulk density variation : a lot of lime that arrives 15 percent less dense delivers 15 percent less mass at the same setting. Gravimetric feeders are immune because they weigh.
Dry feeders discharge into a dissolver or slurry tank with a mixer, and then to the application point. Common problems:
Bridging and rat-holing in the hopper - solved with bin vibrators, air pads, or hopper agitators.
Lime scaling in slurry lines - lime slurry deposits calcium carbonate; lines must be flushable, and sharp elbows should be replaced with sweeps or crosses with removable plugs.
Hygroscopic caking - soda ash and calcium hypochlorite absorb moisture. Store sealed, in a dry room.
3. Gas Chlorination
Gas chlorine systems are built around one safety principle: the entire system downstream of the cylinder operates under vacuum.
The vacuum regulator mounts directly on the cylinder valve and will not open unless the ejector downstream creates a vacuum.
The ejector (injector) uses motive water through a venturi to create that vacuum and to dissolve the gas into solution water.
If a vacuum line breaks, the vacuum is lost, the regulator closes, and air is drawn in rather than chlorine released .
Consequences the exam tests:
Loss of motive water stops chlorine feed. A plugged ejector, a fouled strainer, or low booster pump pressure shows up as loss of chlorine residual, not as a leak.
Feed rate is limited by cylinder withdrawal , not by the chlorinator setting alone. A 150-lb cylinder at 70 degrees F will sustain roughly 40 lb/day ; a one-ton container roughly 400 lb/day . Exceeding that draws liquid over or freezes the cylinder, and frost on the cylinder is the visible warning.
Never apply heat to a cylinder. Add cylinders in parallel instead.
Never install a gas line in a low spot where liquid chlorine can collect and reach the regulator.
4. Day Tanks, Batching and Solution Strength
A day tank holds roughly 24 hours of chemical and is filled from bulk storage. It is worth its cost because it caps the volume that a feed failure or overfeed can release, and because the level trend across a day is an independent check that the pump is feeding.
Batching arithmetic
The controlling relationship for dilution is:
Volume1 x Strength1 = Volume2 x Strength2
To make 300 gallons of 2.0 percent hypochlorite from 12.5 percent stock:
V1 = (300 x 2.0) / 12.5 = 48 gallons of stock , diluted to 300 gallons with 252 gallons of water.
Always add chemical to water, never water to chemical , particularly for acids, where the exotherm can flash the water to steam and eject the contents.
Sodium hypochlorite decay
Sodium hypochlorite is not a stable inventory item. Its available chlorine declines with time, temperature, light exposure, higher initial strength, and trace metals (iron, copper, nickel catalyze decomposition). A 12.5 percent solution stored at 80 degrees F may lose half its strength in three to six months, and decomposition also produces chlorate . Practical controls: buy smaller, more frequent loads; store cool and dark; use diluted (10 to 12.5 percent rather than 15 percent) product; use HDPE, not metal; and verify strength on delivery rather than trusting the label.
5. Drawdown Calibration - the Core Skill
A metering pump's dial setting is a guess. A drawdown test is a measurement.
Procedure
Install a graduated calibration cylinder on the pump suction, valved so the pump can draw from either the cylinder or the day tank.
With the pump running at the setting to be verified, switch suction to the cylinder and note the starting level and the exact time.
Run for a measured interval - long enough that the drop is a large fraction of the cylinder, typically 5 to 15 minutes.
Record the ending level. Switch suction back to the day tank.
Feed rate (gpd) = (Volume drawn, mL / Time, min) x (1 gal / 3,785 mL) x 1,440 min/day
Worked example. A pump draws 640 mL in 10 minutes.
- 640 / 10 = 64 mL/min
- 64 x 1,440 = 92,160 mL/day = 92,160 / 3,785 = 24.35 gallons per day
Now verify the dose. If the chemical is 12.5 percent sodium hypochlorite (specific gravity 1.17) and the plant flow is 1.8 MGD:
- Weight per gallon = 8.34 x 1.17 = 9.76 lb/gal
- Available chlorine per gallon = 9.76 x 0.125 = 1.22 lb/gal
- Chlorine fed = 24.35 gal/day x 1.22 = 29.7 lb/day
- Dose = 29.7 / (1.8 x 8.34) = 1.98 mg/L
Calibrate at more than one setting - a pump can be accurate at 60 percent and badly off at 20 percent - and recalibrate after any repair, any tube or diaphragm change, and any change in chemical supplier or strength.
6. Feed Control Modes
- Mode How it works Where used
- Manual Fixed output Constant-flow plants; always the fallback
Flow-paced (flow proportional) Pump speed follows the flow meter signal, holding dosage constant Coagulant, fluoride, corrosion inhibitor
Residual (feedback) control Analyzer measures residual and trims the pump Chlorine at small, stable systems
Compound loop Flow paces the pump; measured residual trims it Chlorine at larger plants - fastest response with the least overshoot
Feedback-only chlorine control is unstable on variable flow because analyzer lag means the correction arrives after the flow has changed again. Compound loop control gets the bulk of the correction right instantly from flow and uses the residual only for fine trim.
7. Safety Interlocks and Containment
Anti-siphon device (spring-loaded injection quill) on every injection point that can be at lower pressure than the day tank. Without it, a shut-down plant siphons the entire tank into the main.
Feed-on-flow interlock. High-hazard feeds - fluoride above all - must be wired so the metering pump cannot run unless water is flowing, using the flow meter contact or the well pump starter circuit. This is what prevents the classic fluoride overfeed in which a pump keeps running into a static main overnight.
Secondary containment sized for the largest tank plus freeboard, with chemically compatible coating.
Segregate incompatible chemicals. Never store or place fill connections where sodium hypochlorite and acid could be cross-connected - the reaction releases chlorine gas. The same applies to hypochlorite with ammonia (chloramine vapor). Use unique, labeled, keyed fill couplings for every bulk chemical, and supervise every delivery.
Eyewash and safety shower within 10 seconds' travel of any chemical handling point, tested weekly.