Study guide

2.5 Corrosion Control, Softening & Fluoridation Chemistry

Virginia Water/Wastewater Operator Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Virginia Licensing, Regulations & Administrative Standards

1.1 Virginia DPOR Board Structure, License Categories & Scope of Practice 1.2 Experience, Education, Substitutions & Examination Approval 1.3 Renewal, Reinstatement, CPE Requirements & Discipline 1.4 Virginia Drinking Water & Wastewater Environmental Governance 1.5 Facility Classification & Minimum Operator Attendance 1.6 The ABC/WPI Exam Blueprint, References & Test-Day Rules 1.7 License Maintenance, Reporting Duties & Professional Conduct

2 Chapter 2: Source Water & Drinking Water Treatment Unit Processes

2.1 Source Water Hydrology, Groundwater Protection & Raw Water Quality 2.2 Coagulation, Flocculation & Sedimentation Processes 2.3 Filtration Technologies & Media Management 2.4 Disinfection Chemistry, CT Calculations & Disinfection Byproducts 2.5 Corrosion Control, Softening & Fluoridation Chemistry 2.6 Pretreatment: Screening, Presedimentation, Aeration & Preoxidation 2.7 Filter Backwash, Surface Wash, Air Scour & Filter Surveillance 2.8 Membrane Systems: MF, UF, NF and RO Operation & Integrity Testing 2.9 Water Treatment Residuals: Handling, Thickening & Disposal 2.10 Chemical Feed Systems: Metering Pumps, Dry Feeders & Calibration 2.11 Process Monitoring, Trend Interpretation & Plant Optimization 2.12 Iron and Manganese, Taste-and-Odor Control, GAC & PFAS

3 Chapter 3: Wastewater Treatment, Biological Processes & Biosolids

3.1 Preliminary Treatment & Primary Clarification 3.2 Activated Sludge Dynamics & Secondary Process Control 3.3 Attached Growth Systems & Advanced Biological Processes 3.4 Biological & Chemical Nutrient Removal (BNR/ENR) 3.5 Solids Thickening, Digestion & Biosolids Management 3.6 Wastewater Characteristics, Influent Loading & Industrial Pretreatment 3.7 Secondary Clarifier Operation & Sludge Blanket Control 3.8 Lagoons, Stabilization Ponds & Natural Treatment Systems 3.9 Tertiary Filtration, Effluent Polishing & Water Reuse 3.10 Wastewater Disinfection & Dechlorination Systems 3.11 Aeration Systems, Blowers, Diffusers & Dissolved Oxygen Control 3.12 Digester Gas Handling, Cogeneration & Gas System Safety 3.13 Biosolids Land Application, Part 503 & Virginia Permitting

4 Chapter 4: Distribution Networks, Collection Systems & Hydraulic Systems

4.1 Water Distribution Networks, Storage & Pressure Management 4.2 Cross-Connection Control & Backflow Prevention Assemblies 4.3 Wastewater Collection Systems, Lift Stations & Inflow/Infiltration 4.4 Centrifugal & Positive Displacement Pumps 4.5 Motors, Drives, Control Systems & SCADA 4.6 Storage Tank Inspection, Meters, Services & Distribution Appurtenances 4.7 Main Disinfection, Flushing & Distribution Water Quality Management 4.8 Sewer Cleaning, CCTV Inspection & Collection System Rehabilitation 4.9 Maintenance Programs, Asset Management & Pump Efficiency Testing 4.10 Odor Control, Standby Power & Ancillary Plant Equipment

5 Chapter 5: Laboratory Analysis, Environmental Safety & Applied Math

5.1 Water & Wastewater Laboratory Analysis & QA/QC Protocols 5.2 Confined Space Entry, Chemical Safety & OSHA/VOSH Compliance 5.3 Hydraulic, Dosage & Pounds Formula Math 5.4 Wastewater Process & Loading Rate Mathematics 5.5 Drinking Water Microbiology & the Revised Total Coliform Rule 5.6 Wastewater Laboratory Analysis: Nutrients, Metals, WET & Regulatory Testing 5.7 Instrument Calibration, Online Analyzers & Data Validation 5.8 Process Control Testing: Jar Tests, Settleometer & Microscopic Examination 5.9 Chemical Receiving, Storage, Spill Response & Hazardous Waste 5.10 Electrical Safety, Fall Protection, Excavation & Traffic Control 5.11 PPE, Respiratory Protection & Biological Hazards 5.12 Advanced Applied Math: Mass Balance, Blending & Efficiency

6 Chapter 6: Regulatory Compliance, Reporting & Plant Administration

6.1 Safe Drinking Water Act Compliance: MCLs, Monitoring & Violations 6.2 Public Notification, Consumer Confidence Reports & Customer Complaints 6.3 VPDES Permit Compliance, DMRs & Overflow Reporting 6.4 Operating Records, Logbooks, Reports & Data Integrity 6.5 Emergency Response Planning & AWIA Risk and Resilience 6.6 Facility Security, SCADA Cybersecurity & Vulnerability Assessment 6.7 Budgeting, Procurement, Inventory & Capital Planning 6.8 Supervision, Training, SOP Development & Resource Optimization

2.5 Corrosion Control, Softening & Fluoridation Chemistry

Key Takeaways Explain This Topic AI

The EPA Lead and Copper Rule (LCR / LCRI) establishes 90th percentile action levels of 0.015 mg/L (15 ppb) for lead and 1.3 mg/L (1300 ppb) for copper based on first-draw tap samples after a minimum 6-hour stagnation.

Internal corrosion is an electrochemical process driven by an anode (oxidation), cathode (reduction), electrical metallic path, and aqueous electrolyte, accelerated by low pH, low alkalinity, and high Chloride-to-Sulfate Mass Ratios (CSMR > 0.5).

The Langelier Saturation Index (LSI = pH - pHs) indicates calcium carbonate precipitation potential: LSI > 0 is supersaturated (scale-forming), LSI < 0 is under-saturated (corrosive), and LSI = 0 is in chemical equilibrium.

Lime-soda ash softening precipitates carbonate hardness using hydrated lime (Ca(OH)2) and noncarbonate hardness using soda ash (Na2CO3), requiring two-stage recarbonation with carbon dioxide (CO2) to stabilize pH and prevent downstream filter cementing.

Community fluoridation targets 0.7 mg/L fluoride ion using hydrofluorosilicic acid (H2SiF6), sodium fluorosilicate (Na2SiF6), or sodium fluoride (NaF), requiring vacuum anti-siphon protection and electrical flow-pumping interlocks.

Last updated: August 2026

Electrochemical Corrosion & Lead/Copper Leaching

Corrosion in water distribution networks and customer premise plumbing is the electrochemical deterioration of metallic pipe materials driven by reactions with the aqueous environment. Uncontrolled corrosion causes pipe failure, hydraulic capacity reduction (tuberculation), aesthetic water degradation (red water from iron, blue-green staining from copper), and public health risks from toxic heavy metal leaching ( lead and copper ). [ AQUEOUS ELECTROLYTE (Conductive Water) ]

  • ^
  • |
  • [ ANODE SITE ] -----------------+-----------------> [ CATHODE SITE ]
  • Metal Dissolves into Water Electrons Consumed
  • M -> M^n+ + n e- O2 + 2 H2O + 4 e- -> 4 OH-
  • (e.g., Pb -> Pb2+ + 2 e-) (e.g., Oxygen Reduction)
  • | ^
  • +======> METALLIC PIPE WALL (Electron Flow) =======+
  • The Four Components of an Electrochemical Corrosion Cell

Anode : The oxidation site on the metallic surface where metal atoms lose electrons and dissolve into solution as cations ( F e → F e 2 + + 2 e − Fe \rightarrow Fe^{2+} + 2e^- F e → F e 2 + + 2 e − or P b → P b 2 + + 2 e − Pb \rightarrow Pb^{2+} + 2e^- P b → P b 2 + + 2 e − ).

Cathode : The reduction site where migrating electrons are consumed by dissolved chemical species, typically dissolved oxygen ( O 2 + 2 H 2 O + 4 e − → 4 O H − O_2 + 2H_2O + 4e^- \rightarrow 4OH^- O 2 ​ + 2 H 2 ​ O + 4 e − → 4 O H − ) or hydrogen ions in acidic water ( 2 H + + 2 e − → H 2 ↑ 2H^+ + 2e^- \rightarrow H_2\uparrow 2 H + + 2 e − → H 2 ​ ↑ ).

Metallic Conductor : The physical pipe wall that transports electrons from the anode to the cathode.

Electrolyte : The conductive water solution containing dissolved mineral ions completing the electrical circuit between cathode and anode.

Primary Forms of Internal Corrosion

Uniform / General Corrosion : Even, widespread metal loss across the interior pipe surface.

Pitting Corrosion : Severe, localized anodic attack in stagnant areas or beneath mineral scales, leading to rapid pinhole pipe perforation.

Galvanic Corrosion : Accelerated corrosion occurring when two dissimilar metals are in direct physical contact within a conductive electrolyte (e.g., copper pipe joined directly to a lead service line or galvanized iron). The metal with lower electrochemical potential (the less noble metal, such as lead or zinc) becomes a sacrificial anode and corrodes rapidly.

Chloride-to-Sulfate Mass Ratio (CSMR) : The numerical ratio of chloride concentration to sulfate concentration in finished water: CSMR = [ C l − ] in mg/L [ S O 4 2 − ] in mg/L \text{CSMR} = \frac{[Cl^-] \text{ in mg/L}}{[SO_4^{2-}] \text{ in mg/L}} CSMR = [ S O 4 2 − ​ ] in mg/L [ C l − ] in mg/L ​

When CSMR > 0.50 \text{CSMR} > 0.50 CSMR > 0.50 in waters with low alkalinity ( < 50 mg/L < 50\text{ mg/L} < 50 mg/L ), galvanic corrosion at lead-solder/copper joints accelerates dramatically, causing extreme lead spikes at customer taps.

Lead & Copper Rule (LCR / LCRI) Regulatory Standards

The EPA Lead and Copper Rule (and Lead and Copper Rule Improvements - LCRI) regulates heavy metal corrosion products at the consumer's tap rather than at the treatment plant outfall.

Action Levels & Compliance Monitoring

Lead Action Level (AL) : 0.015 mg/L ( 15 μ g/L or 15 ppb) \mathbf{0.015\text{ mg/L}} \text{ (}15\,\mu\text{g/L or } 15\text{ ppb)} 0.015 mg/L ( 15 μ g/L or 15 ppb)

Copper Action Level (AL) : 1.3 mg/L ( 1300 μ g/L or 1.3 ppm) \mathbf{1.3\text{ mg/L}} \text{ (}1300\,\mu\text{g/L or } 1.3\text{ ppm)} 1.3 mg/L ( 1300 μ g/L or 1.3 ppm)

Maximum Contaminant Level Goal (MCLG) : Lead = 0 mg/L 0\text{ mg/L} 0 mg/L (non-threshold toxicant); Copper = 1.3 mg/L 1.3\text{ mg/L} 1.3 mg/L .

Sampling Protocol & 90th Percentile Calculation

Sample Collection : 1-liter first-draw tap samples collected from targeted consumer kitchen/bathroom taps after the water has remained completely motionless in interior plumbing for a minimum 6-hour stagnation period .

Tiered Monitoring Pools : Samples must be collected from high-risk locations: Tier 1 Sites (single-family residences with lead service lines, lead interior plumbing, or copper plumbing with lead solder installed between 1982 and 1988).

90th Percentile Evaluation : All valid sample results are arranged in ascending numerical order from lowest to highest. The concentration at the 90th percentile position is compared against the Action Level: Rank Position = Total Valid Samples × 0.90 \text{Rank Position} = \text{Total Valid Samples} \times 0.90 Rank Position = Total Valid Samples × 0.90

(For example, in a 50-sample monitoring pool, the 45th ranked result is the 90th percentile value) .

Mandatory Actions upon Action Level Exceedance

If the 90th percentile lead concentration exceeds 0.015 mg/L 0.015\text{ mg/L} 0.015 mg/L :

Deliver public education materials to all bill-paying customers within 60 days.

Conduct Water Quality Parameter (WQP) monitoring (pH, alkalinity, calcium, conductivity, orthophosphate) throughout the distribution network.

Install or optimize Optimal Corrosion Control Treatment (OCCT) approved by VDH.

Implement mandatory lead service line replacement programs.

Corrosion Control Treatment (CCT) & Saturation Indices

Utilities utilize three primary mechanisms to mitigate internal corrosion:

1. pH & Alkalinity Adjustment

Raising pH and dissolved inorganic carbon (DIC) decreases hydrogen ion availability and lowers lead/copper solubility:

Hydrated Lime ( C a ( O H ) 2 Ca(OH)_2 C a ( O H ) 2 ​ ) : Adds calcium hardness, carbonate alkalinity, and raises pH simultaneously; low chemical cost.

Soda Ash ( N a 2 C O 3 Na_2CO_3 N a 2 ​ C O 3 ​ ) : Adds carbonate alkalinity and raises pH without increasing calcium hardness.

Caustic Soda ( N a O H NaOH N a O H , 25% or 50% solution) : Rapidly increases pH; converts dissolved bicarbonate to carbonate; does not add hardness; 50 % 50\% 50% solution freezes at 54 ∘ F 54^\circ\text{F} 5 4 ∘ F ( 12 ∘ C 12^\circ\text{C} 1 2 ∘ C ).

2. Passivating Corrosion Inhibitors

Orthophosphate ( P O 4 3 − PO_4^{3-} P O 4 3 − ​ ) : Forms an insoluble crystalline microscopic passivation barrier directly on interior pipe surfaces, converting soluble lead into insoluble Hydroxylpyromorphite ( P b 5 ( P O 4 ) 3 O H Pb_5(PO_4)_3OH P b 5 ​ ( P O 4 ​ ) 3 ​ O H ) and copper into Tenorite ( C u O CuO C u O ) and Malachite ( C u 2 C O 3 ( O H ) 2 Cu_2CO_3(OH)_2 C u 2 ​ C O 3 ​ ( O H ) 2 ​ ).

Target residual: 1.0 to 3.0 mg/L as P O 4 1.0\text{ to }3.0\text{ mg/L as } PO_4 1.0 to 3.0 mg/L as P O 4 ​ .

Operational Rule : Orthophosphate feed must remain uninterrupted; a drop in residual causes the protective passivation scale to re-dissolve within days.

Zinc Orthophosphate : Formulations containing zinc ( Z n 2 + Zn^{2+} Z n 2 + ) in 1 : 1 to 1 : 5 1:1\text{ to }1:5 1 : 1 to 1 : 5 ratios with orthophosphate; zinc accelerates cathodic film formation and shields cement-lined pipes from calcium leaching.

Polyphosphates (e.g., Sodium Hexametaphosphate): Sequestering agents used to keep iron and manganese in solution; generally ineffective for lead corrosion control and may increase lead solubility.

3. Calcium Carbonate Saturation Indices

Langelier Saturation Index ( L S I LSI L S I ) : Quantifies the thermodynamic driving force for calcium carbonate ( C a C O 3 CaCO_3 C a C O 3 ​ ) scale deposition or dissolution: L S I = p H − p H s LSI = pH - pH_s L S I = p H − p H s ​

Where p H pH p H is the actual measured water pH, and p H s pH_s p H s ​ is the theoretical saturation pH calculated from temperature, TDS, calcium hardness, and total alkalinity. LSI < 0 (Negative) LSI = 0 (Balanced) LSI > 0 (Positive)

  • ----------------- ------------------ ------------------
  • Under-saturated Chemical Equilibrium Supersaturated
  • Dissolves CaCO3 Scale Neither Dissolves nor Precipitates CaCO3 Scale
  • Corrosive Tendency Precipitates Scale Protective Scale / Clogging

Ryznar Stability Index ( R S I RSI RS I ) : Empirical indicator: R S I = 2 ( p H s ) − p H RSI = 2(pH_s) - pH RS I = 2 ( p H s ​ ) − p H .

R S I < 6.0 RSI < 6.0 RS I < 6.0 : Heavy scale-forming tendency.

R S I = 6.0 to 7.0 RSI = 6.0\text{ to }7.0 RS I = 6.0 to 7.0 : Balanced, non-aggressive water.

R S I > 7.5 RSI > 7.5 RS I > 7.5 : Aggressive, highly corrosive water.

Calcium Carbonate Precipitation Potential (CCPP) : Quantitative mass of C a C O 3 CaCO_3 C a C O 3 ​ that will precipitate or dissolve from solution (target: + 4 to + 10 mg/L as C a C O 3 +4\text{ to }+10\text{ mg/L as } CaCO_3 + 4 to + 10 mg/L as C a C O 3 ​ ).

Water Hardness & Softening Chemistry

Hardness is defined as the concentration of multivalent metallic cations in water, dominated by Calcium ( C a 2 + Ca^{2+} C a 2 + ) and Magnesium ( M g 2 + Mg^{2+} M g 2 + ) .

Hardness Classifications Total Hardness (TH) = Calcium Hardness (CH) + Magnesium Hardness (MH) \text{Total Hardness (TH)} = \text{Calcium Hardness (CH)} + \text{Magnesium Hardness (MH)} Total Hardness (TH) = Calcium Hardness (CH) + Magnesium Hardness (MH) Total Hardness (TH) = Carbonate Hardness (CH) + Noncarbonate Hardness (NCH) \text{Total Hardness (TH)} = \text{Carbonate Hardness (CH)} + \text{Noncarbonate Hardness (NCH)} Total Hardness (TH) = Carbonate Hardness (CH) + Noncarbonate Hardness (NCH)

Carbonate Hardness (Temporary Hardness) : Hardness chemically paired with bicarbonate ( H C O 3 − HCO_3^- H C O 3 − ​ ) and carbonate ( C O 3 2 − CO_3^{2-} C O 3 2 − ​ ); precipitates when heated or treated with lime.

Noncarbonate Hardness (Permanent Hardness) : Hardness paired with sulfate ( S O 4 2 − SO_4^{2-} S O 4 2 − ​ ), chloride ( C l − Cl^- C l − ), or nitrate ( N O 3 − NO_3^- N O 3 − ​ ); requires soda ash for chemical precipitation.

Classification Total Hardness Range (mg/L as C a C O 3 CaCO_3 C a C O 3 ​ ) Total Hardness Range (grains per gallon - gpg)

Soft 0 − 60 mg/L 0 - 60\text{ mg/L} 0 − 60 mg/L 0 − 3.5 gpg 0 - 3.5\text{ gpg} 0 − 3.5 gpg

Moderately Hard 61 − 120 mg/L 61 - 120\text{ mg/L} 61 − 120 mg/L 3.5 − 7.0 gpg 3.5 - 7.0\text{ gpg} 3.5 − 7.0 gpg

  • Hard 121 − 180 mg/L 121 - 180\text{ mg/L} 121 − 180 mg/L 7.0 − 10.5 gpg 7.0 - 10.5\text{ gpg} 7.0 − 10.5 gpg
  • Very Hard > 180 mg/L > 180\text{ mg/L} > 180 mg/L > 10.5 gpg > 10.5\text{ gpg} > 10.5 gpg

(Conversion: 1 grain per gallon (gpg) = 17.12 mg/L as C a C O 3 1\text{ grain per gallon (gpg)} = 17.12\text{ mg/L as } CaCO_3 1 grain per gallon (gpg) = 17.12 mg/L as C a C O 3 ​ )

Chemical Precipitation Softening (Lime-Soda Ash Process)

Chemical precipitation softening removes hardness cations by converting them into insoluble precipitates: Calcium Carbonate ( C a C O 3 ↓ CaCO_3\downarrow C a C O 3 ​ ↓ ) and Magnesium Hydroxide ( M g ( O H ) 2 ↓ Mg(OH)_2\downarrow M g ( O H ) 2 ​ ↓ ) . 1. Carbon Dioxide Neutralization: CO2 + Ca(OH)2 -------------> CaCO3(s) + H2O

  • 2. Calcium Carbonate Hardness: Ca(HCO3)2 + Ca(OH)2 ---------> 2 CaCO3(s) + 2 H2O [pH 9.0-9.5]
  • 3. Magnesium Carbonate Hardness: Mg(HCO3)2 + 2 Ca(OH)2 -------> Mg(OH)2(s) + 2 CaCO3(s) [pH 10.8-11.2]
  • 4. Calcium Noncarbonate Hardness: CaSO4 + Na2CO3 -------------> CaCO3(s) + Na2SO4
  • 5. Magnesium Noncarbonate: MgSO4 + Ca(OH)2 + Na2CO3 ---> Mg(OH)2(s) + CaCO3(s) + Na2SO4
  • The Two-Stage Recarbonation Process

Water leaving high-lime softening basins at p H 10.8 − 11.2 pH\,10.8-11.2 p H 10.8 − 11.2 is super-saturated with caustic alkalinity and fine colloidal calcium carbonate. If pumped directly onto sand filters, it will precipitate C a C O 3 CaCO_3 C a C O 3 ​ , cementing media grains together ( filter sand incrustation ) and clogging distribution mains.

To stabilize softened water, Carbon Dioxide gas ( C O 2 CO_2 C O 2 ​ ) is injected in two stages:

Primary Recarbonation : Injected between softening clarifiers to lower pH to ∼ 9.5 \sim 9.5 ∼ 9.5 , precipitating supersaturated calcium carbonate before final clarification.

Secondary Recarbonation : Injected upstream of filtration to lower pH to ∼ 8.4 − 8.8 \sim 8.4-8.8 ∼ 8.4 − 8.8 , converting remaining carbonate ions into soluble bicarbonate: C a C O 3 ( s ) + C O 2 + H 2 O → C a ( H C O 3 ) 2 ( Stabilization ) CaCO_3(s) + CO_2 + H_2O \rightarrow Ca(HCO_3)_2 \quad (\text{Stabilization}) C a C O 3 ​ ( s ) + C O 2 ​ + H 2 ​ O → C a ( H C O 3 ​ ) 2 ​ ( Stabilization )

Ion Exchange Softening

For smaller utilities or groundwater wells, Ion Exchange utilizes synthetic strong-acid cation (SAC) polystyrene resin beads saturated with sodium ions ( R - N a R\text{-}Na R - N a ). Water passes through the resin bed, where multivalent hardness cations are exchanged for sodium: 2 R - N a + C a 2 + ⇌ R 2 - C a + 2 N a + ( Softening Mode ) 2R\text{-}Na + Ca^{2+} \rightleftharpoons R_2\text{-}Ca + 2Na^+ \quad (\text{Softening Mode}) 2 R - N a + C a 2 + ⇌ R 2 ​ - C a + 2 N a + ( Softening Mode )

When resin active sites are exhausted, the vessel is restored via a 4-step regeneration cycle:

Backwash : Upward water flow ( 5 − 8 gpm/ft 2 5-8\text{ gpm/ft}^2 5 − 8 gpm/ft 2 ) to expand the bed and flush captured particulates.

Brine Injection : Downward application of a concentrated 10 % to 15 % 10\%\text{ to }15\% 10% to 15% Sodium Chloride ( N a C l NaCl N a Cl ) brine solution, driving the chemical equilibrium in reverse by mass action to displace C a 2 + Ca^{2+} C a 2 + and M g 2 + Mg^{2+} M g 2 + .

Slow Rinse (Displacement) : Slowly pushes residual brine through the resin.

Fast Rinse : High-velocity rinse to flush waste brine to disposal before returning to service.

Fluoridation Chemistry, Feed Systems & Safety

Community water fluoridation is the controlled addition of fluoride to public drinking water to prevent dental caries (tooth decay) in children and adults.

Public Health Standard & Chemicals

Target Optimal Dosage : 0.70 mg/L 0.70\text{ mg/L} 0.70 mg/L (established by the US Public Health Service / CDC).

EPA Maximum Contaminant Level (MCL) : 4.0 mg/L 4.0\text{ mg/L} 4.0 mg/L (enforceable standard preventing crippling skeletal fluorosis).

EPA Secondary MCL (SMCL) : 2.0 mg/L 2.0\text{ mg/L} 2.0 mg/L (non-enforceable aesthetic guideline preventing cosmetic dental fluorosis/mottling).

Chemical Compound Formula & Physical Form Purity & Available Fluoride Ion (AFI) Handling & Operational Notes

Hydrofluorosilicic Acid (FSA) H 2 S i F 6 H_2SiF_6 H 2 ​ S i F 6 ​ / Straw-colored liquid 23 − 25 % 23-25\% 23 − 25% Solution; AFI = 0.792 \text{AFI} = 0.792 AFI = 0.792 ( 79.2 % F − 79.2\%\text{ F}^- 79.2% F − ) Density ∼ 10.2 lb/gal \sim 10.2\text{ lb/gal} ∼ 10.2 lb/gal . Fed directly without dilution using positive displacement diaphragm/peristaltic pumps. Never dilute with hard water (causes silica scaling).

Sodium Fluorosilicate N a 2 S i F 6 Na_2SiF_6 N a 2 ​ S i F 6 ​ / White crystalline powder 98 − 99 % 98-99\% 98 − 99% Powder; AFI = 0.607 \text{AFI} = 0.607 AFI = 0.607 ( 60.7 % F − 60.7\%\text{ F}^- 60.7% F − ) Moderate solubility ( 0.76 g/100 mL 0.76\text{ g/100 mL} 0.76 g/100 mL ); fed using volumetric/gravimetric dry feeders into a continuous dissolving tank.

Sodium Fluoride N a F NaF N a F / White powder or crystals 97 − 98 % 97-98\% 97 − 98% Solid; AFI = 0.452 \text{AFI} = 0.452 AFI = 0.452 ( 45.2 % F − 45.2\%\text{ F}^- 45.2% F − ) Constant 4.0 % 4.0\% 4.0% saturation solubility ( 18 , 000 mg/L F − 18,000\text{ mg/L F}^- 18 , 000 mg/L F − ) across broad temperatures in saturator tanks. Requires softened water.

Fluoride Chemical Feed Rate Math Feed Rate (lb/day) = Plant Flow (MGD) × Desired Fluoride Dose (mg/L) × 8.34 lb/gal Chemical Purity (decimal) × Available Fluoride Fraction (AFI decimal) \text{Feed Rate (lb/day)} = \frac{\text{Plant Flow (MGD)} \times \text{Desired Fluoride Dose (mg/L)} \times 8.34\text{ lb/gal}}{\text{Chemical Purity (decimal)} \times \text{Available Fluoride Fraction (AFI decimal)}} Feed Rate (lb/day) = Chemical Purity (decimal) × Available Fluoride Fraction (AFI decimal) Plant Flow (MGD) × Desired Fluoride Dose (mg/L) × 8.34 lb/gal ​

Fluoride Feed System Safety & Overfeed Protection

Because acute fluoride overfeed ( > 5 − 10 mg/L > 5-10\text{ mg/L} > 5 − 10 mg/L ) can cause severe gastrointestinal toxicity and fatal cardiac arrest, fluoride installations mandate multiple redundant fail-safe systems:

Anti-Siphon Protection : Positive displacement metering pumps must be equipped with spring-loaded anti-siphon injection quills ( 15 − 25 psi 15-25\text{ psi} 15 − 25 psi cracking pressure) and vacuum relief valves to prevent chemical siphoning during main line depressurization.

Electrical & Hydraulic Interlocks : Chemical metering pump power must be hardwired directly in series with the main water line flow meter or well pump control circuit; the chemical feeder cannot energize unless positive water flow is verified .

Day Tank on Weighing Scales : Limit chemical storage to a 24-hour day tank mounted on a precision digital scale with high-loss alarm limits.

Operator PPE : Hydrofluorosilicic acid ( H 2 S i F 6 H_2SiF_6 H 2 ​ S i F 6 ​ ) releases highly toxic hydrogen fluoride ( H F HF H F ) and silicon tetrafluoride vapors. Operators must wear a full-face shield, neoprene acid-resistant apron, heavy neoprene gloves, safety boots, and an approved half-mask respirator equipped with acid gas cartridges.

Loading diagram... Corrosion Control, Softening & Fluoridation Unit Operations