Study guide

8.2 Vehicle Components, Maintenance & Malfunctions

Washington Driving Instructor Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Washington Instructor Licensing & Professional Standards

1.1 Instructor Eligibility: Age, Driving Record & Education 1.2 The 100-Hour Instructor Training Course & Approved Providers 1.3 Background Checks, Fingerprinting & Disqualifying Conduct 1.4 The DOL Knowledge & Skills Exams, Fees and Application Sequence 1.5 Licence Term, Renewal, Continuing Professional Development & Reinstatement

2 Chapter 2: Driver Training School Licensing, Facilities & Enforcement

2.1 School Licensing, Insurance & the Established Place of Business 2.2 Classroom Space, Branch Offices & the 1,000-Foot Rule 2.3 Instructional Vehicles: Equipment, Signage & Inspection 2.4 Records, Reporting Deadlines & Departmental Inspection 2.5 Discipline, Unprofessional Conduct, Appeals & Penalties

3 Chapter 3: Course Design, Required Curriculum & Student Completion

3.1 Course Requirements: Hours, Pacing & the 30-Day Rule 3.2 Behind-the-Wheel Instruction, Observation & Simulation Hours 3.3 The Washington Required Curriculum Standards 3.4 Student Accomplishment, Certificates & the Parent Night 3.5 School-Administered Licensing Examinations & Testing Integrity

4 Chapter 4: Professional Practice, Ethics, Data & Safety

4.1 Professionalism, Ethics & Professional Boundaries 4.2 Student Data, Privacy & Records Confidentiality 4.3 Safety Protocols, Risk Management & the Wireless Device Prohibition 4.4 Equity, Accessibility, Professional Growth & Target Zero

5 Chapter 5: Washington Graduated Driver Licensing

5.1 The Instruction Permit: Eligibility, Waiver, Term & Fees 5.2 Permit Conditions & the Instructor as Statutory Supervisor 5.3 Intermediate Driver Licence Eligibility 5.4 IDL Restrictions, Exemptions & the Three-Strike Sanction System 5.5 Driver Education Requirements for Applicants Under 25

6 Chapter 6: Washington Rules of the Road - Right-of-Way, Speed & Lane Use

6.1 Right-of-Way, Intersections & Turning Movements 6.2 Modern Roundabouts 6.3 Speed Regulation & the Basic Speed Rule 6.4 Emergency and Work Zones & the Move Over Law 6.5 Lane Use, Passing & Following Distance

7 Chapter 7: Washington Rules of the Road - Protecting Other Road Users

7.1 Pedestrians, Crosswalks & Sharing the Road 7.2 School Buses & Railroad Grade Crossings 7.3 Impaired Driving, Implied Consent & Underage Zero Tolerance 7.4 Distracted, Negligent & Reckless Driving 7.5 Occupant Protection, Collisions & Financial Responsibility

8 Chapter 8: Traffic Control Devices & Vehicle Knowledge

8.1 Signs, Signals & Pavement Markings 8.2 Vehicle Components, Maintenance & Malfunctions 8.3 Vehicle Safety Technology & Driver Assistance Systems

9 Chapter 9: The Driving Task, Risk Management & Vehicle Dynamics

9.1 Visual Search Habits & the Smith System 9.2 The IPDE and SIPDE Processes 9.3 Zone Control & Lane Positioning 9.4 Natural Laws, Stopping Distance & Vehicle Balance 9.5 Emergencies & Adverse Conditions

10 Chapter 10: Classroom Teaching Methodology

10.1 Learning Domains & Bloom's Taxonomy 10.2 Lesson Planning, Objectives & Scaffolding 10.3 Interactive Strategies, Technology & Student Engagement 10.4 Classroom Management & Challenging Behaviours 10.5 Assessment, Feedback & Adapting Instruction

11 Chapter 11: Behind-the-Wheel Instruction & Skills Evaluation

11.1 Pre-Drive Procedures & the Cockpit Drill 11.2 Reference Points & Vehicle Positioning 11.3 Dual-Control Operation & Emergency Intervention 11.4 Commentary Driving, Coaching & Observer Engagement 11.5 Precision Manoeuvres, Complex Environments & the Skills Test

8.2 Vehicle Components, Maintenance & Malfunctions

Key Takeaways Explain This Topic AI

WAC 308-108-155(2)(a) makes vehicle components and vehicle maintenance and malfunctions two separate required classroom standards, and Instructor Standard 2.2 requires foundational knowledge of vehicle mechanics and maintenance.

Instructor Standard 2.2.2 requires the instructor to inspect the vehicle for safety before behind-the-wheel lessons and to recognise annual inspection requirements.

Every instructional vehicle must carry an annual inspection form meeting DOL criteria conducted by or for the school owner, and must be used exclusively for driver training whenever instruction is being given.

Tyre condition, brake response, lighting and glass are the four checks with the highest safety return in a daily pre-drive inspection.

Last updated: September 2026

8.2 Vehicle Components, Maintenance & Malfunctions

Note

Two required standards, not one. WAC 308-108-155(2)(a)(ii) requires teaching vehicle components , and (a)(iii) separately requires vehicle maintenance and malfunctions . The behind-the-wheel twin, (b)(i), is vehicle components and safety technology . A course that mentions the dashboard in passing does not satisfy three standards.

Systems a driver education course must cover

Braking. Hydraulic service brakes on all four wheels, a separate parking brake, and on virtually every modern vehicle an anti-lock braking system. Students should know that firm continuous pressure is correct with ABS, that the pedal pulsation and noise are the system working, and that the parking brake is a mechanical backup that can be used for a controlled stop if the service brakes fail.

Steering and suspension. Power assistance means steering effort rises sharply if the engine stops. Students must know that a stalled engine does not lock the steering while the key is in the run position, but it does make the wheel very heavy and the brakes very hard.

Tyres. The only contact with the road, and the component with the highest safety return per minute of attention. Cover inflation pressure (found on the driver's door jamb placard, not the tyre sidewall), tread depth, uneven wear as a symptom of alignment or inflation problems, sidewall damage, and load and speed ratings.

Lighting. Headlamps on low and high beam, daytime running lamps, tail lamps, brake lamps, turn signals, hazard warning lamps, reversing lamps and licence plate illumination. Teach the legal duty to use headlamps from half an hour after sunset to half an hour before sunrise and whenever visibility is reduced, and the courtesy rule of dipping high beams for oncoming and followed traffic.

Glass, mirrors and wipers. Vision is the whole task. Wiper blades are a consumable; washer fluid should be topped up as routine, especially in a training vehicle running all day.

Engine, cooling, electrical and fuel. Enough for a driver to understand a temperature gauge, a battery warning, an oil pressure warning and a low fuel state, and to know that a temperature or oil pressure warning means stop, not continue to the destination.

Restraint systems. Belts, pretensioners and airbags as a single system: an airbag is a supplemental restraint that assumes a belted occupant.

Warning indicators students must recognise

Indicator Meaning Correct response

Red brake warning Parking brake engaged, low fluid, or hydraulic fault Confirm the parking brake is off; if it stays lit, stop safely and do not drive

  • Red oil pressure Loss of oil pressure Stop immediately and shut down - continuing destroys the engine
  • Red temperature Overheating Stop, shut down, do not open the cooling system while hot
  • Battery or charging Charging system fault Reduce electrical load and drive directly to service
  • ABS Anti-lock function disabled Normal brakes remain; increase following distance, service soon
  • Airbag Restraint system fault Service promptly; the airbag may not deploy

Tyre pressure monitoring One or more tyres significantly underinflated Check pressures at the next safe opportunity

Check engine, steady Emissions or engine management fault Service soon

Check engine, flashing Active misfire capable of damaging the catalyst Reduce load and stop driving as soon as safe

The red-versus-amber distinction is the teachable principle: red generally means stop now; amber generally means arrange service.

The daily pre-drive inspection

Instructor Standard 2.2.2 requires the instructor to "inspect the vehicle for safety before behind-the-wheel lessons " and 2.2.3 to "identify potential safety concerns related to the instructional vehicle and conduct vehicle safety checks regularly ." A two-minute routine covers it:

Walk the vehicle.

All four tyres - visible inflation, tread, no sidewall damage or embedded objects.

Lights - headlamps, tail lamps, brake lamps, both turn signals, hazards. Use a wall or a helper.

Glass and mirrors - no obstructing damage; mirrors intact.

Student driver signage displayed and legible, as RCW 46.82.360(2)(c) requires at all times when instruction is being given.

No fluid pooling under the vehicle.

Inside. 6. Dual brake - full travel, firm, and the brake lamps illuminate when depressed. On a manual, the dual clutch as well.

7. Instructor's rear view mirror adjusted to your seated eye position.

8. Warning lamps illuminate at key-on and extinguish after start.

9. Fuel and washer fluid adequate for the lesson.

10. Emergency equipment present : twenty-piece first aid kit, secured and fully charged fire extinguisher, and the strobe, triangle or two eighteen-inch cones - WAC 308-108-110(1)(a).

Items 4, 6, 7 and 10 are compliance items as well as safety items. Items 1 to 3 and 8 are what you should be teaching the student to do on their own vehicle for the rest of their life.

Maintenance intervals and the training fleet

WAC 308-108-110(1)(b) requires an annual vehicle inspection form meeting DOL's minimum equipment and safety criteria, "conducted by or for the school owner." WAC 308-108-140(1)(d) requires that report to be on file at the main school location for all vehicles in use, not less than annually. WAC 308-108-110(2) requires the original insurance policy, current registrations and the annual inspection report to be kept at the primary place of business, and RCW 46.82.360(8)(c) requires vehicle records to be retained five years .

Beyond the compliance minimum, a training vehicle accumulates unusual wear: constant low-speed manoeuvring, frequent hard-ish braking during interventions, and a clutch operated by learners. Sensible practice is to inspect brakes and tyres far more often than annually, to track dual-control linkage wear specifically, and to log every check so the annual report is a summary rather than a scramble.

WAC 308-108-140(1)(e) requires reporting to DOL within 10 days any vehicle added to or removed from instructional service, and WAC 308-108-140(1)(b) bars a collision-involved vehicle from returning to service until an inspection report has been forwarded to the department.

Teaching maintenance to a novice

Anchor it to consequences, not to schedules. "Check your tyres monthly" is forgettable. "Underinflated tyres lengthen your stopping distance and are the main cause of blowouts" is not.

Make the owner's manual a required object. Have students find, in their own vehicle's manual: the recommended tyre pressure, the oil change interval, and the meaning of two warning lamps.

Use the placard, not the sidewall. The number moulded into the tyre sidewall is the maximum pressure, not the recommended pressure. The recommended figure is on the driver's door jamb.

Teach the coin test, then improve on it. A tread depth gauge is better, but a coin gives students something they can do today.

Rehearse "what would you do" for each red lamp. Ten minutes of scenario work now is worth more than an hour of component naming.

  • Warning
  • Exam traps in this section

Vehicle components and vehicle maintenance and malfunctions are two separate required standards.

The annual inspection is conducted by or for the school owner , on a form meeting DOL criteria - no specific technician certification is required by rule.

Vehicle records are kept five years , unlike the three-year student record period.

Recommended tyre pressure comes from the door jamb placard , not the sidewall.

Red warning lamps mean stop; amber means arrange service.